Saeed Mahameed says:

====================
mlx5-updates-2018-12-19

This series adds some misc updates and the support for tunnels over VLAN
tc offloads.

From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock

From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128

From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.

Patch 4 avoids crash for TC flow with egress upper devices

Patch 5 refactors tunnel routing devs into a helper function

Patch 6 avoids crash for TC encap flows with vlan on underlay

Patches 7-8 refactor encap tunnel header preparing code.

Patch 9 adds support for building VLAN tagged ETH header.

Patch 10 adds support for tunnel routing to VLAN device.

From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Two usability improvements

This patchset contains two small improvements in the mlxsw driver. The
first one, in patches #1-#2, relieves the user from the need to
configure a VLAN interface and only later the corresponding VXLAN
tunnel. The issue is explained in detail in the first patch.

The second improvement is described below and allows the user to make
use of VID 1 by having the driver use the reserved 4095 VID for untagged
traffic.

VLAN entries on a given port can be associated with either a bridge or a
router. For example, if swp1.10 is assigned an IP address and swp1.20 is
enslaved to a VLAN-unaware bridge, then both {Port 1, VID 10} and {Port
1, VID 20} would be associated with a filtering identifier (FID) of the
correct type.

In case swp1 itself is assigned an IP address or enslaved to a
VLAN-unaware bridge, then a FID would be associated with {Port 1, VID
1}. Using VID 1 for this purpose means that VLAN devices with VID 1
cannot be created over mlxsw ports, as this VID is (ab)used as the
default VLAN.

Instead of using VID 1 for this purpose, we can use VID 4095 which is
reserved for internal use and cannot be configured by either the 8021q
or the bridge driver.

Patches #3-#7 perform small and non-functional changes that finally
allow us to switch to VID 4095 as the default VID in patch #8.

Patch #9 removes the limitation about creation of VLAN devices with VID
1 over mlxsw ports.

Patches #10-#11 add test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.

Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.

The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.

Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.

The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.

Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.

Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.

Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).

Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch added the ability to offload a VXLAN tunnel used for L3
VNI when it is present in the VLAN-aware bridge before the corresponding
VLAN interface is configured. This patch adds a test case to verify
that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.

In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.

The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.

Instead, call into the bridge code which will check if NVE should be
enabled on the FID.

This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-12-20

This series contains updates to e100, igb, ixgbe, i40e and ice drivers.

I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics.  This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.

Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.

Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.

YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.

Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.

Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.

Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.

Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in.  This was due to the
driver not setting PME during runtime suspend.

Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the mii_bus callbacks to address the entire clause 22/45 address
space.  Enables userspace to poke switch registers instead of a single
PHY address.

The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock.  This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.

While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.

Since commit 42eca230 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.

To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.

Fixes: 42eca230 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.

See commit 13a8cd19 ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Out of bound read reported by KASan.

i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as

  tbl->entry_size + dev->neigh_priv_len

where "dev" is a net_device.

But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
 e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.

Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some pointers to the definition of the CBS algorithm, and some
notes about the limits of its implementation in the i210 family of
controllers.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.

The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.

The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
 on CPU0.

In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.

CC: Bernhard Kaindl  <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Michael Chan says:

====================
bnxt_en: Update for net-next.

Three main changes in this series, besides the usual firmware spec
update:

1. Add support for a new firmware communication channel direct to the
firmware processor that handles flow offloads.  This speeds up
flow offload operations.

2. Use 64-bit internal flow handles to increase the number of flows
that can be offloaded.

3. Add level-2 context memory paging so that we can configure more
context memory for RDMA on the 57500 chips.  Allocate more context
memory if RDMA is enabled on the 57500 chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For a little better performance on faster machines and faster link
speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.

This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls()
to allocate and free pages for context memory.  The new functions
will handle the different levels of paging support and allocate/free
the pages accordingly using the existing functions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To support level 2 context page memory structures, enhance the
bnxt_ring_mem_info structure with a "depth" field to specify the page
level and add a flag to specify using full pages for L1 and L2 page
tables.  This is needed to support RDMA functionality on 57500 chips
since RDMA requires more context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed
by KONG processor were sent to the CHIMP processor from the host. This
approach was taken as there was no direct message channel to KONG.
CHIMP in turn used to send them to KONG. Newer firmware supports a new
message channel which the host can send messages directly to the KONG
processor.

This patch adds support for required changes needed in the driver
to support direct KONG message channel.  This speeds up flow related
messages sent to the firmware for CLS_FLOWER offload.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These routines will be enhanced in the subsequent patch to
return the 2nd firmware comm. channel's hwrm response address &
sequence id respectively.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for adding a 2nd communication channel to firmware.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set hwrm_intr_seq_id value to its inverted value instead of
HWRM_SEQ_INVALID, when an hwrm completion of type
CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use
the complete 16-bit sequence ID space.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The major changes are in the flow offload firmware APIs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2018-12-20

Two last patches for this release cycle:

1) Remove an unused variable in xfrm_policy_lookup_bytype().
   From YueHaibing.

2) Fix possible infinite loop in __xfrm6_tunnel_alloc_spi().
   Also from YueHaibing.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull m68k fix from Geert Uytterhoeven:
 "Fix memblock-related crashes"

* tag 'm68k-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Fix memblock-related crashes

Merge tag 'kbuild-fixes-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fix from Masahiro Yamada:
 "Fix false positive warning/error about missing library for objtool"

* tag 'kbuild-fixes-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: fix false positive warning/error about missing libelf