Capture struct vcpu_vmx in a local variable to improve the readability
of vmx_{g,s}et_rflags().

No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Skip the VMWRITE to update GUEST_CR3 if CR3 is not available, i.e. has
not been read from the VMCS since the last VM-Enter.  If vcpu->arch.cr3
is stale, kvm_read_cr3(vcpu) will refresh vcpu->arch.cr3 from the VMCS,
meaning KVM will do a VMREAD and then VMWRITE the value it just pulled
from the VMCS.

Note, this is a purely theoretical change, no instances of skipping
the VMREAD+VMWRITE have been observed with this change.
Tested-by: Reto Buerki <reet@codelabs.ch>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Performing a WBINVD and DF_FLUSH are expensive operations. Currently, a
WBINVD/DF_FLUSH is performed every time an SEV guest terminates. However,
the WBINVD/DF_FLUSH is only required when an ASID is being re-allocated
to a new SEV guest. Also, a single WBINVD/DF_FLUSH can enable all ASIDs
that have been disassociated from guests through DEACTIVATE.

To reduce the number of WBINVD/DF_FLUSH invocations, introduce a new ASID
bitmap to track ASIDs that need to be reclaimed. When an SEV guest is
terminated, add its ASID to the reclaim bitmap instead of clearing the
bitmap in the existing SEV ASID bitmap. This delays the need to perform a
WBINVD/DF_FLUSH invocation when an SEV guest terminates until all of the
available SEV ASIDs have been used. At that point, the WBINVD/DF_FLUSH
invocation can be performed and all ASIDs in the reclaim bitmap moved to
the available ASIDs bitmap.

The semaphore around DEACTIVATE can be changed to a read semaphore with
the semaphore taken in write mode before performing the WBINVD/DF_FLUSH.
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Performing a WBINVD and DF_FLUSH are expensive operations. The SEV support
currently performs this WBINVD/DF_FLUSH combination when an SEV guest is
terminated, so there is no need for it to be done before LAUNCH.

However, when the SEV firmware transitions the platform from UNINIT state
to INIT state, all ASIDs will be marked invalid across all threads.
Therefore, as part of transitioning the platform to INIT state, perform a
WBINVD/DF_FLUSH after a successful INIT in the PSP/SEV device driver.
Since the PSP/SEV device driver is x86 only, it can reference and use the
WBINVD related functions directly.

Cc: Gary Hook <gary.hook@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Write the desired L2 CR3 into vmcs02.GUEST_CR3 during nested VM-Enter
instead of deferring the VMWRITE until vmx_set_cr3().  If the VMWRITE
is deferred, then KVM can consume a stale vmcs02.GUEST_CR3 when it
refreshes vmcs12->guest_cr3 during nested_vmx_vmexit() if the emulated
VM-Exit occurs without actually entering L2, e.g. if the nested run
is squashed because nested VM-Enter (from L1) is putting L2 into HLT.

Note, the above scenario can occur regardless of whether L1 is
intercepting HLT, e.g. L1 can intercept HLT and then re-enter L2 with
vmcs.GUEST_ACTIVITY_STATE=HALTED.  But practically speaking, a VMM will
likely put a guest into HALTED if and only if it's not intercepting HLT.

In an ideal world where EPT *requires* unrestricted guest (and vice
versa), VMX could handle CR3 similar to how it handles RSP and RIP,
e.g. mark CR3 dirty and conditionally load it at vmx_vcpu_run().  But
the unrestricted guest silliness complicates the dirty tracking logic
to the point that explicitly handling vmcs02.GUEST_CR3 during nested
VM-Enter is a simpler overall implementation.

Cc: stable@vger.kernel.org
Reported-and-tested-by: Reto Buerki <reet@codelabs.ch>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The SEV firmware DEACTIVATE command disassociates an SEV guest from an
ASID, clears the WBINVD indicator on all threads and indicates that the
SEV firmware DF_FLUSH command must be issued before the ASID can be
re-used. The SEV firmware DF_FLUSH command will return an error if a
WBINVD has not been performed on every thread before it has been invoked.
A window exists between the WBINVD and the invocation of the DF_FLUSH
command where an SEV firmware DEACTIVATE command could be invoked on
another thread, clearing the WBINVD indicator. This will cause the
subsequent SEV firmware DF_FLUSH command to fail which, in turn, results
in the SEV firmware ACTIVATE command failing for the reclaimed ASID.
This results in the SEV guest failing to start.

Use a mutex to close the WBINVD/DF_FLUSH window by obtaining the mutex
before the DEACTIVATE and releasing it after the DF_FLUSH. This ensures
that any DEACTIVATE cannot run before a DF_FLUSH has completed.

Fixes: 59414c98 ("KVM: SVM: Add support for KVM_SEV_LAUNCH_START command")
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The SEV ASID bitmap currently is not protected against parallel SEV guest
startups. This can result in an SEV guest failing to start because another
SEV guest could have been assigned the same ASID value. Use a mutex to
serialize access to the SEV ASID bitmap.

Fixes: 1654efcb ("KVM: SVM: Add KVM_SEV_INIT command")
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Merge tag 'kvm-ppc-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD

PPC KVM fix for 5.4

- Fix a bug in the XIVE code which can cause a host crash.

Merge tag 'kvmarm-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm fixes for 5.4, take #2

Special PMU edition:

- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow

After resetting the vCPU, the kvmclock MSR keeps the previous value but it is
not enabled.  This can be confusing, so fix it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Use BUG_ON instead of a if condition followed by BUG.

Generated by: scripts/coccinelle/misc/bugon.cocci

Fixes: 4b526de5 ("KVM: x86: Check kvm_rebooting in kvm_spurious_fault()")
CC: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Commit bf653b78 ("KVM: vmx: Introduce handle_unexpected_vmexit
and handle WAITPKG vmexit") introduced specialized handling of
specific exit-reasons that should not be raised by CPU because
KVM configures VMCS such that they should never be raised.

However, since commit 7396d337 ("KVM: x86: Return to userspace
with internal error on unexpected exit reason"), VMX & SVM
exit handlers were modified to generically handle all unexpected
exit-reasons by returning to userspace with internal error.

Therefore, there is no need for specialized handling of specific
unexpected exit-reasons (This specialized handling also introduced
inconsistency for these exit-reasons to silently skip guest instruction
instead of return to userspace on internal-error).

Fixes: bf653b78 ("KVM: vmx: Introduce handle_unexpected_vmexit and handle WAITPKG vmexit")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Commit 204c91ef ("KVM: selftests: do not blindly clobber registers in
 guest asm") was intended to make test more gcc-proof, however, the result
is exactly the opposite: on newer gccs (e.g. 8.2.1) the test breaks with

==== Test Assertion Failure ====
  x86_64/sync_regs_test.c:168: run->s.regs.regs.rbx == 0xBAD1DEA + 1
  pid=14170 tid=14170 - Invalid argument
     1	0x00000000004015b3: main at sync_regs_test.c:166 (discriminator 6)
     2	0x00007f413fb66412: ?? ??:0
     3	0x000000000040191d: _start at ??:?
  rbx sync regs value incorrect 0x1.

Apparently, compile is still free to play games with registers even
when they have variables attached.

Re-write guest code with 'asm volatile' by embedding ucall there and
making sure rbx is preserved.

Fixes: 204c91ef ("KVM: selftests: do not blindly clobber registers in guest asm")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

vmx_dirty_log_test fails on AMD and this is no surprise as it is VMX
specific. Bail early when nested VMX is unsupported.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

vmx_* tests require VMX and three of them implement the same check. Move it
to vmx library.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

vmx_set_nested_state_test() checks if VMX is supported twice: in the very
beginning (and skips the whole test if it's not) and before doing
test_vmx_nested_state(). One should be enough.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Don't waste cycles to shrink/grow vCPU halt_poll_ns if host
side polling is disabled.
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Because "Untracked files:" are annoying.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

When the RDPID instruction is supported on the host, enumerate it in
KVM_GET_SUPPORTED_CPUID.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull pin control fixes from Linus Walleij:
 "Here is a bunch of pin control fixes. I was lagging behind on this
  one, some fixes should have come in earlier, sorry about that.

  Anyways here it is, pretty straight-forward fixes, the Strago fix
  stand out as something serious affecting a lot of machines.

  Summary:
   - Handle multiple instances of Intel chips without complaining.
   - Restore the Intel Strago DMI workaround
   - Make the Armada 37xx handle pins over 32
   - Fix the polarity of the LED group on Armada 37xx
   - Fix an off-by-one bug in the NS2 driver
   - Fix error path for iproc's platform_get_irq()
   - Fix error path on the STMFX driver
   - Fix a typo in the Berlin AS370 driver
   - Fix up misc errors in the Aspeed 2600 BMC support
   - Fix a stray SPDX tag"

* tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: aspeed-g6: Rename SD3 to EMMC and rework pin groups
  pinctrl: aspeed-g6: Fix UART13 group pinmux
  pinctrl: aspeed-g6: Make SIG_DESC_CLEAR() behave intuitively
  pinctrl: aspeed-g6: Fix I3C3/I3C4 pinmux configuration
  pinctrl: aspeed-g6: Fix I2C14 SDA description
  pinctrl: aspeed-g6: Sort pins for sanity
  dt-bindings: pinctrl: aspeed-g6: Rework SD3 function and groups
  pinctrl: berlin: as370: fix a typo s/spififib/spdifib
  pinctrl: armada-37xx: swap polarity on LED group
  pinctrl: stmfx: fix null pointer on remove
  pinctrl: iproc: allow for error from platform_get_irq()
  pinctrl: ns2: Fix off by one bugs in ns2_pinmux_enable()
  pinctrl: bcm-iproc: Use SPDX header
  pinctrl: armada-37xx: fix control of pins 32 and up
  pinctrl: cherryview: restore Strago DMI workaround for all versions
  pinctrl: intel: Allocate IRQ chip dynamic

Merge tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild fixes from Masahiro Yamada:

 - fix a bashism of setlocalversion

 - do not use the too new --sort option of tar

* tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kheaders: substituting --sort in archive creation
  scripts: setlocalversion: fix a bashism
  kbuild: update comment about KBUILD_ALLDIRS

Pull x86 fixes from Thomas Gleixner:
 "A small set of x86 fixes:

   - Prevent a NULL pointer dereference in the X2APIC code in case of a
     CPU hotplug failure.

   - Prevent boot failures on HP superdome machines by invalidating the
     level2 kernel pagetable entries outside of the kernel area as
     invalid so BIOS reserved space won't be touched unintentionally.

     Also ensure that memory holes are rounded up to the next PMD
     boundary correctly.

   - Enable X2APIC support on Hyper-V to prevent boot failures.

   - Set the paravirt name when running on Hyper-V for consistency

   - Move a function under the appropriate ifdef guard to prevent build
     warnings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/acpi: Move get_cmdline_acpi_rsdp() under #ifdef guard
  x86/hyperv: Set pv_info.name to "Hyper-V"
  x86/apic/x2apic: Fix a NULL pointer deref when handling a dying cpu
  x86/hyperv: Make vapic support x2apic mode
  x86/boot/64: Round memory hole size up to next PMD page
  x86/boot/64: Make level2_kernel_pgt pages invalid outside kernel area

Pull irq fixes from Thomas Gleixner:
 "A small set of irq chip driver fixes and updates:

   - Update the SIFIVE PLIC interrupt driver to use the fasteoi handler
     to address the shortcomings of the existing flow handling which was
     prone to lose interrupts

   - Use the proper limit for GIC interrupt line numbers

   - Add retrigger support for the recently merged Anapurna Labs Fabric
     interrupt controller to make it complete

   - Enable the ATMEL AIC5 interrupt controller driver on the new
     SAM9X60 SoC"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/sifive-plic: Switch to fasteoi flow
  irqchip/gic-v3: Fix GIC_LINE_NR accessor
  irqchip/atmel-aic5: Add support for sam9x60 irqchip
  irqchip/al-fic: Add support for irq retrigger

Pull hrtimer fixlet from Thomas Gleixner:
 "A single commit annotating the lockcless access to timer->base with
  READ_ONCE() and adding the WRITE_ONCE() counterparts for completeness"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hrtimer: Annotate lockless access to timer->base

Pull stop-machine fix from Thomas Gleixner:
 "A single fix, amending stop machine with WRITE/READ_ONCE() to address
  the fallout of KCSAN"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  stop_machine: Avoid potential race behaviour

The PMU emulation code uses the perf event sample period to trigger
the overflow detection. This works fine  for the *first* overflow
handling, but results in a huge number of interrupts on the host,
unrelated to the number of interrupts handled in the guest (a x20
factor is pretty common for the cycle counter). On a slow system
(such as a SW model), this can result in the guest only making
forward progress at a glacial pace.

It turns out that the clue is in the name. The sample period is
exactly that: a period. And once the an overflow has occured,
the following period should be the full width of the associated
counter, instead of whatever the guest had initially programed.

Reset the sample period to the architected value in the overflow
handler, which now results in a number of host interrupts that is
much closer to the number of interrupts in the guest.

Fixes: b02386eb ("arm64: KVM: Add PMU overflow interrupt routing")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

The current convention for KVM to request a chained event from the
host PMU is to set bit[0] in attr.config1 (PERF_ATTR_CFG1_KVM_PMU_CHAINED).

But as it turns out, this bit gets set *after* we create the kernel
event that backs our virtual counter, meaning that we never get
a 64bit counter.

Moving the setting to an earlier point solves the problem.

Fixes: 80f393a2 ("KVM: arm/arm64: Support chained PMU counters")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Of PMCR_EL0.LC, the ARMv8 ARM says:

	"In an AArch64 only implementation, this field is RES 1."

So be it.

Fixes: ab946834 ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

When a counter is disabled, its value is sampled before the event
is being disabled, and the value written back in the shadow register.

In that process, the value gets truncated to 32bit, which is adequate
for any counter but the cycle counter (defined as a 64bit counter).

This obviously results in a corrupted counter, and things like
"perf record -e cycles" not working at all when run in a guest...
A similar, but less critical bug exists in kvm_pmu_get_counter_value.

Make the truncation conditional on the counter not being the cycle
counter, which results in a minor code reorganisation.

Fixes: 80f393a2 ("KVM: arm/arm64: Support chained PMU counters")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reported-by: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>

Pull networking fixes from David Miller:
 "I was battling a cold after some recent trips, so quite a bit piled up
  meanwhile, sorry about that.

  Highlights:

   1) Fix fd leak in various bpf selftests, from Brian Vazquez.

   2) Fix crash in xsk when device doesn't support some methods, from
      Magnus Karlsson.

   3) Fix various leaks and use-after-free in rxrpc, from David Howells.

   4) Fix several SKB leaks due to confusion of who owns an SKB and who
      should release it in the llc code. From Eric Biggers.

   5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.

   6) Jumbo packets don't work after resume on r8169, as the BIOS resets
      the chip into non-jumbo mode during suspend. From Heiner Kallweit.

   7) Corrupt L2 header during MPLS push, from Davide Caratti.

   8) Prevent possible infinite loop in tc_ctl_action, from Eric
      Dumazet.

   9) Get register bits right in bcmgenet driver, based upon chip
      version. From Florian Fainelli.

  10) Fix mutex problems in microchip DSA driver, from Marek Vasut.

  11) Cure race between route lookup and invalidation in ipv4, from Wei
      Wang.

  12) Fix performance regression due to false sharing in 'net'
      structure, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
  net: reorder 'struct net' fields to avoid false sharing
  net: dsa: fix switch tree list
  net: ethernet: dwmac-sun8i: show message only when switching to promisc
  net: aquantia: add an error handling in aq_nic_set_multicast_list
  net: netem: correct the parent's backlog when corrupted packet was dropped
  net: netem: fix error path for corrupted GSO frames
  macb: propagate errors when getting optional clocks
  xen/netback: fix error path of xenvif_connect_data()
  net: hns3: fix mis-counting IRQ vector numbers issue
  net: usb: lan78xx: Connect PHY before registering MAC
  vsock/virtio: discard packets if credit is not respected
  vsock/virtio: send a credit update when buffer size is changed
  mlxsw: spectrum_trap: Push Ethernet header before reporting trap
  net: ensure correct skb->tstamp in various fragmenters
  net: bcmgenet: reset 40nm EPHY on energy detect
  net: bcmgenet: soft reset 40nm EPHYs before MAC init
  net: phy: bcm7xxx: define soft_reset for 40nm EPHY
  net: bcmgenet: don't set phydev->link from MAC
  net: Update address for MediaTek ethernet driver in MAINTAINERS
  ipv4: fix race condition between route lookup and invalidation
  ...

Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.

Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)

So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.

We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.

We move in the first cache line fields that can be
dirtied often.

We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.

Fixes: 355b9855 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.

Fixes: 83c0afae ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam.  Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: netem: fix further issues with packet corruption

This set is fixing two more issues with the netem packet corruption.

First patch (which was previously posted) avoids NULL pointer dereference
if the first frame gets freed due to allocation or checksum failure.
v2 improves the clarity of the code a little as requested by Cong.

Second patch ensures we don't return SUCCESS if the frame was in fact
dropped. Thanks to this commit message for patch 1 no longer needs the
"this will still break with a single-frame failure" disclaimer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.

Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To corrupt a GSO frame we first perform segmentation.  We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.

If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.

Commit 177b8007 ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.

Backlog corrections for parent qdiscs have to be adjusted.

Fixes: 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.

In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.

For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.

Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().

Remove the superfluous module_put().

Fixes: 279f438e ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>