- 11 May, 2016 40 commits
-
-
K. Y. Srinivasan authored
commit 1db488d1 upstream. On the consumer side, we have interrupt driven flow management of the producer. It is sufficient to base the signaling decision on the amount of space that is available to write after the read is complete. The current code samples the previous available space and uses this in making the signaling decision. This state can be stale and is unnecessary. Since the state can be stale, we end up not signaling the host (when we should) and this can result in a hang. Fix this problem by removing the unnecessary check. I would like to thank Arseney Romanenko <arseneyr@microsoft.com> for pointing out this issue. Also, issue a full memory barrier before making the signaling descision to correctly deal with potential reordering of the write (read index) followed by the read of pending_sz. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stanislav Meduna authored
commit d1306eb6 upstream. This patch fixes the issue where the mxs_ocotp_read is reading the ocotp in reg_size steps but decrements the remaining size by 1. The number of iterations is thus four times higher, overwriting the area behind the output buffer. Fixes: c01e9a11 ("nvmem: add driver for ocotp in i.MX23 and i.MX28") Tested-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Stanislav Meduna <stano@meduna.org> Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
-
Johan Hovold authored
commit 9be427ef upstream. This reverts commit e3345db8, which broke system resume for a large class of devices. Devices that after having been reset during resume need to be rebound due to a missing reset_resume callback, are now left in a suspended state. This specifically broke resume of common USB-serial devices, which are now unusable after system suspend (until disconnected and reconnected) when USB persist is enabled. During resume, usb_resume_interface will set the needs_binding flag for such interfaces, but unlike system resume, run-time resume does not honour it. Signed-off-by:
Johan Hovold <johan@kernel.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Jasem Mutlaq authored
commit 613ac23a upstream. Adding VID:PID for Straizona Focusers to cp210x driver. Signed-off-by:
Jasem Mutlaq <mutlaqja@ikarustech.com> Signed-off-by:
-
Mike Manning authored
commit 1d377f4d upstream. The Link ECU is an aftermarket ECU computer for vehicles that provides full tuning abilities as well as datalogging and displaying capabilities via the USB to Serial adapter built into the device. Signed-off-by:
Mike Manning <michael@bsch.com.au> Signed-off-by:
-
Srinivas Kandagatla authored
commit 17dcc37e upstream. On some SOCs PORTS_IMPL register value is never programmed by the firmware and left at zero value. Which means that no sata ports are available for software. AHCI driver used to cope up with this by fabricating the port_map if the PORTS_IMPL register is read zero, but recent patch broke this workaround as zero value was valid for NVMe disks. This patch adds ports-implemented DT bindings as workaround for this issue in a way that DT can can override the PORTS_IMPL register in cases where the firmware did not program it already. Fixes: 566d1827 ("libata: disable forced PORTS_IMPL for >= AHCI 1.3") Signed-off-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Andy Gross <andy.gross@linaro.org> Signed-off-by:
-
Srinivas Kandagatla authored
commit 2fd0f46c upstream. In usecases where force_port_map is used saved_port_map is never set, resulting in not programming the PORTS_IMPL register as part of initial config. This patch fixes this by setting it to port_map even in case where force_port_map is used, making it more inline with other parts of the code. Fixes: 566d1827 ("libata: disable forced PORTS_IMPL for >= AHCI 1.3") Signed-off-by:
-
Anton Blanchard authored
commit b4c11211 upstream. In create_zero_mask() we have: addi %1,%2,-1 andc %1,%1,%2 popcntd %0,%1 using the "r" constraint for %2. r0 is a valid register in the "r" set, but addi X,r0,X turns it into an li: li r7,-1 andc r7,r7,r0 popcntd r4,r7 Fix this by using the "b" constraint, for which r0 is not a valid register. This was found with a kernel build using gcc trunk, narrowed down to when -frename-registers was enabled at -O2. It is just luck however that we aren't seeing this on older toolchains. Thanks to Segher for working with me to find this issue. Fixes: d0cebfa6 ("powerpc: word-at-a-time optimization for 64-bit Little Endian") Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Prarit Bhargava authored
commit 93d68841 upstream. ACPICA commit 7a3bd2d962f221809f25ddb826c9e551b916eb25 Set the mutex owner thread ID. Original patch from: Prarit Bhargava <prarit@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=115121 Link: https://github.com/acpica/acpica/commit/7a3bd2d9Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Tested-by: Andy Lutomirski <luto@kernel.org> # On a Dell XPS 13 9350 Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Srinivas Kandagatla authored
commit bb4add2c upstream. This patch adds new ports-implemented mask, which is required to get achi working on the mainline. Without this patch value read from PORTS_IMPL register which is zero would not enable any ports for software to use. Fixes: 566d1827 ("libata: disable forced PORTS_IMPL for >= AHCI 1.3") Signed-off-by:
-
Wang YanQing authored
commit c10fcb14 upstream. The code for checking whether a BAR address range is valid will break out of the loop when a start address of 0x0 is encountered. This behaviour is wrong since by breaking out of the loop we may miss the BAR that describes the EFI frame buffer in a later iteration. Because of this bug I can't use video=efifb: boot parameter to get efifb on my new ThinkPad E550 for my old linux system hard disk with 3.10 kernel. In 3.10, efifb is the only choice due to DRM/I915 not supporting the GPU. This patch also add a trivial optimization to break out after we find the frame buffer address range without testing later BARs. Signed-off-by:
Wang YanQing <udknight@gmail.com> [ Rewrote changelog. ] Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by:
Peter Jones <pjones@redhat.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1462454061-21561-2-git-send-email-matt@codeblueprint.co.ukSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Vineet Gupta authored
commit e5bc0478 upstream. While reviewing a different change to asm-generic/io.h Arnd spotted that ARC ioread32 and ioread32be both of which come from asm-generic versions are not symmetrical in terms of calling the io barriers. generic ioread32 -> ARC readl() [ has barriers] generic ioread32be -> __be32_to_cpu(__raw_readl()) [ lacks barriers] While generic ioread32be is being remediated to call readl(), that involves a swab32(), causing double swaps on ioread32be() on Big Endian systems. So provide our versions of big endian IO accessors to ensure io barrier calls while also keeping them optimal Suggested-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Sudeep Holla authored
commit 2482bc31 upstream. The sti-cpufreq does unconditional registration of the cpufreq-dt driver which causes issue on an multi-platform build. For example, on Vexpress TC2 platform, we get the following error on boot: cpu cpu0: OPP-v2 not supported cpu cpu0: Not doing voltage scaling cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19 cpu cpu0: dev_pm_opp_get_max_volt_latency: Invalid regulator (-6) ... arm_big_little: bL_cpufreq_register: Failed registering platform driver: vexpress-spc, err: -17 The actual driver fails to initialise as cpufreq-dt is probed successfully, which is incorrect. This issue can happen to any platform not using cpufreq-dt in a multi-platform build. This patch adds a check to do selective initialization of the driver. Fixes: ab0ea257 (cpufreq: st: Provide runtime initialised driver for ST's platforms) Signed-off-by:
Sudeep Holla <sudeep.holla@arm.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Dmitry V. Levin authored
commit f0b22d1b upstream. Do not load one entry beyond the end of the syscall table when the syscall number of a traced process equals to __NR_Linux_syscalls. Similar bug with regular processes was fixed by commit 3bb457af ("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls"). This bug was found by strace test suite. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
James Morse authored
commit 625fe4f8 upstream. arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't update 'ret' with this value, meaning we always signal success to cpuidle_enter_state(), causing it to update the usage counters as if we succeeded. Fixes: 191de17a ("ARM64: cpuidle: Replace cpu_suspend by the common ARM/ARM64 function") Signed-off-by:
James Morse <james.morse@arm.com> Acked-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Chen Yu authored
commit 886123fb upstream. Currently we read the tsc radio: ratio = (MSR_PLATFORM_INFO >> 8) & 0x1f; Thus we get bit 8-12 of MSR_PLATFORM_INFO, however according to the SDM (35.5), the ratio bits are bit 8-15. Ignoring the upper bits can result in an incorrect tsc ratio, which causes the TSC calibration and the Local APIC timer frequency to be incorrect. Fix this problem by masking 0xff instead. [ tglx: Massaged changelog ] Fixes: 7da7c156 "x86, tsc: Add static (MSR) TSC calibration on Intel Atom SoCs" Signed-off-by:
Chen Yu <yu.c.chen@intel.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Bin Gao <bin.gao@intel.com> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/1462505619-5516-1-git-send-email-yu.c.chen@intel.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Matt Fleming authored
commit e8dfe6d8 upstream. Mark reported that having asterisks on the end of directory names confuses get_maintainer.pl when it encounters subdirectories, and that my name does not appear when run on drivers/firmware/efi/libstub. Reported-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Howard Cochran authored
commit 74d36944 upstream. Commit 947e9762 ("writeback: update wb_over_bg_thresh() to use wb_domain aware operations") unintentionally changed this function's meaning from "are there more dirty pages than the background writeback threshold" to "are there more dirty pages than the writeback threshold". The background writeback threshold is typically half of the writeback threshold, so this had the effect of raising the number of dirty pages required to cause a writeback worker to perform background writeout. This can cause a very severe performance regression when a BDI uses BDI_CAP_STRICTLIMIT because balance_dirty_pages() and the writeback worker can now disagree on whether writeback should be initiated. For example, in a system having 1GB of RAM, a single spinning disk, and a "pass-through" FUSE filesystem mounted over the disk, application code mmapped a 128MB file on the disk and was randomly dirtying pages in that mapping. Because FUSE uses strictlimit and has a default max_ratio of only 1%, in balance_dirty_pages, thresh is ~200, bg_thresh is ~100, and the dirty_freerun_ceiling is the average of those, ~150. So, it pauses the dirtying processes when we have 151 dirty pages and wakes up a background writeback worker. But the worker tests the wrong threshold (200 instead of 100), so it does not initiate writeback and just returns. Thus, balance_dirty_pages keeps looping, sleeping and then waking up the worker who will do nothing. It remains stuck in this state until the few dirty pages that we have finally expire and we write them back for that reason. Then the whole process repeats, resulting in near-zero throughput through the FUSE BDI. The fix is to call the parameterized variant of wb_calc_thresh, so that the worker will do writeback if the bg_thresh is exceeded which was the behavior before the referenced commit. Fixes: 947e9762 ("writeback: update wb_over_bg_thresh() to use wb_domain aware operations") Signed-off-by:
Howard Cochran <hcochran@kernelspring.com> Acked-by:
Miklos Szeredi <mszeredi@redhat.com> Tested-by Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Dan Williams authored
commit 658922e5 upstream. When configuring a pfn-device instance to allocate the memmap array it needs to account for the fact that vmemmap_populate_hugepages() allocates struct page blocks in HPAGE_SIZE chunks. We need to align the reserved area size to 2MB otherwise arch_add_memory() runs out of memory while establishing the memmap: WARNING: CPU: 0 PID: 496 at arch/x86/mm/init_64.c:704 arch_add_memory+0xe7/0xf0 [..] Call Trace: [<ffffffff8148bdb3>] dump_stack+0x85/0xc2 [<ffffffff810a749b>] __warn+0xcb/0xf0 [<ffffffff810a75cd>] warn_slowpath_null+0x1d/0x20 [<ffffffff8106a497>] arch_add_memory+0xe7/0xf0 [<ffffffff811d2097>] devm_memremap_pages+0x287/0x450 [<ffffffff811d1ffa>] ? devm_memremap_pages+0x1ea/0x450 [<ffffffffa0000298>] __wrap_devm_memremap_pages+0x58/0x70 [nfit_test_iomap] [<ffffffffa0047a58>] pmem_attach_disk+0x318/0x420 [nd_pmem] [<ffffffffa0047bcf>] nd_pmem_probe+0x6f/0x90 [nd_pmem] [<ffffffffa0009469>] nvdimm_bus_probe+0x69/0x110 [libnvdimm] [..] ndbus0: nd_pmem.probe(pfn3.0) = -12 nd_pmem: probe of pfn3.0 failed with error -12 libndctl: ndctl_pfn_enable: pfn3.0: failed to enable Reported-by:
Namratha Kothapalli <namratha.n.kothapalli@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Sven Eckelmann authored
commit d1a65f17 upstream. _batadv_update_route rcu_derefences orig_ifinfo->router outside of a spinlock protected region to print some information messages to the debug log. But this pointer is not checked again when the new pointer is assigned in the spinlock protected region. Thus is can happen that the value of orig_ifinfo->router changed in the meantime and thus the reference counter of the wrong router gets reduced after the spinlock protected region. Just rcu_dereferencing the value of orig_ifinfo->router inside the spinlock protected region (which also set the new pointer) is enough to get the correct old router object. Fixes: e1a5382f ("batman-adv: Make orig_node->router an rcu protected pointer") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
-
Linus Lüssing authored
commit c4fdb6cf upstream. When removing a single interface while a broadcast or ogm packet is still pending then we will free the forward packet without releasing the queue slots again. This patch is supposed to fix this issue. Fixes: 6d5808d4 ("batman-adv: Add missing hardif_free_ref in forw_packet_free") Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> [sven@narfation.org: fix conflicts with current version] Signed-off-by:
-
Sven Eckelmann authored
commit c7829666 upstream. The encapsulated ethernet and VLAN header may be outside the received ethernet frame. Thus the skb buffer size has to be checked before it can be parsed to find out if it encapsulates another batman-adv packet. Fixes: 42019357 ("batman-adv: softif bridge loop avoidance") Signed-off-by:
-
Antonio Quartulli authored
commit 2871734e upstream. Now that DAT is VLAN aware, it must use the VID when computing the DHT address of the candidate nodes where an entry is going to be stored/retrieved. Fixes: be1db4f6 ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by:
-
Jason Baron authored
commit bc22af74 upstream. Khugepaged attempts to raise min_free_kbytes if its set too low. However, on boot khugepaged sets min_free_kbytes first from subsys_initcall(), and then the mm 'core' over-rides min_free_kbytes after from init_per_zone_wmark_min(), via a module_init() call. Khugepaged used to use a late_initcall() to set min_free_kbytes (such that it occurred after the core initialization), however this was removed when the initialization of min_free_kbytes was integrated into the starting of the khugepaged thread. The fix here is simply to invoke the core initialization using a core_initcall() instead of module_init(), such that the previous initialization ordering is restored. I didn't restore the late_initcall() since start_stop_khugepaged() already sets min_free_kbytes via set_recommended_min_free_kbytes(). This was noticed when we had a number of page allocation failures when moving a workload to a kernel with this new initialization ordering. On an 8GB system this restores min_free_kbytes back to 67584 from 11365 when CONFIG_TRANSPARENT_HUGEPAGE=y is set and either CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y or CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y. Fixes: 79553da2 ("thp: cleanup khugepaged startup") Signed-off-by:
Jason Baron <jbaron@akamai.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
David Rientjes <rientjes@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Mathias Krause authored
commit 8148a73c upstream. If /proc/<PID>/environ gets read before the envp[] array is fully set up in create_{aout,elf,elf_fdpic,flat}_tables(), we might end up trying to read more bytes than are actually written, as env_start will already be set but env_end will still be zero, making the range calculation underflow, allowing to read beyond the end of what has been written. Fix this as it is done for /proc/<PID>/cmdline by testing env_end for zero. It is, apparently, intentionally set last in create_*_tables(). This bug was found by the PaX size_overflow plugin that detected the arithmetic underflow of 'this_len = env_end - (env_start + src)' when env_end is still zero. The expected consequence is that userland trying to access /proc/<PID>/environ of a not yet fully set up process may get inconsistent data as we're in the middle of copying in the environment variables. Fixes: https://forums.grsecurity.net/viewtopic.php?f=3&t=4363 Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=116461Signed-off-by:
Mathias Krause <minipli@googlemail.com> Cc: Emese Revfy <re.emese@gmail.com> Cc: Pax Team <pageexec@freemail.hu> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Knut Wohlrab authored
commit 6984ab1a upstream. A wrong decoding of the touch coordinate message causes a wrong touch ID. Touch ID for dual touch must be 0 or 1. According to the actual Neonode nine byte touch coordinate coding, the state is transported in the lower nibble and the touch ID in the higher nibble of payload byte five. Signed-off-by:
Knut Wohlrab <Knut.Wohlrab@de.bosch.com> Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Nazar Mokrynskyi authored
commit 567a44ec upstream. Needed for v2 of the device firmware, otherwise kernel will stuck for few seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot. Signed-off-by:
Nazar Mokrynskyi <nazar@mokrynskyi.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Ping Cheng authored
commit e1123fe9 upstream. DTK-1651 is a display pen-only tablet Signed-off-by:
Ping Cheng <pingc@wacom.com> Signed-off-by:
-
Jan Beulich authored
commit 27e0e638 upstream. The copying of ring data was wrong for two cases: For a full ring nothing got copied at all (as in that case the canonicalized producer and consumer indexes are identical). And in case one or both of the canonicalized (after the resize) indexes would point into the second half of the buffer, the copied data ended up in the wrong (free) part of the new buffer. In both cases uninitialized data would get passed back to the caller. Fix this by simply copying the old ring contents twice: Once to the low half of the new buffer, and a second time to the high half. This addresses the inability to boot a HVM guest with 64 or more vCPUs. This regression was caused by 86200154 (xen/evtchn: dynamically grow pending event channel ring). Reported-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Ross Lagerwall authored
commit dfd74a1e upstream. Commit 55b3da98 (xen/balloon: find non-conflicting regions to place hotplugged memory) caused a regression in 4.4. When ballooning on an x86 32 bit PAE system with close to 64 GiB of memory, the address returned by allocate_resource may be above 64 GiB. When using CONFIG_SPARSEMEM, this setup is limited to using physical addresses < 64 GiB. When adding memory at this address, it runs off the end of the mem_section array and causes a crash. Instead, fail the ballooning request. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by:
-
Ross Lagerwall authored
commit 60901df3 upstream. Commit 1084b198 (xen: Add Xen specific page definition) caused a regression in 4.4. The xen functions to convert between pages and pfns fail due to an overflow on systems where a physical address may not fit in an unsigned long (e.g. x86 32 bit PAE systems). Rework the conversion to avoid overflow. This should also result in simpler object code. This bug manifested itself as disk corruption with Linux 4.4 when using blkfront in a Xen HVM x86 32 bit guest with more than 4 GiB of memory. Signed-off-by:
-
Sascha Hauer authored
commit 5616f367 upstream. The secondary CPU starts up in ARM mode. When the kernel is compiled in thumb2 mode we have to explicitly compile the secondary startup trampoline in ARM mode, otherwise the CPU will go to Nirvana. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reported-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Suggested-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Dinh Nguyen <dinguyen@opensource.altera.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit a0a966b8 upstream. We want to skip reparenting a clock on turning on power domain, if we do not have the parent yet. The parent is obtained when turning the domain off. However due to a typo, the loop is continued on IS_ERR() of clock being reparented, not on the IS_ERR() of the parent. Theoretically this could lead to OOPS on first turn on of a power domain, if there was no turn off before. Practically that should never happen because all power domains are turned on by default (reset value, bootloader does not turn off them usually) so the first action will be always turn off. Fixes: 29e5eea0 ("ARM: EXYNOS: Get current parent clock for power domain on/off") Reported-by:
Vladimir Zapolskiy <vz@mleia.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Philipp Zabel authored
commit acbef7b7 upstream. Since the wildcard at the end of OF module aliases is gone, autoloading of modules that don't match a device's last (most generic) compatible value fails. For example the CODA960 VPU on i.MX6Q has the SoC specific compatible "fsl,imx6q-vpu" and the generic compatible "cnm,coda960". Since the driver currently only works with knowledge about the SoC specific integration, it doesn't list "cnm,cod960" in the module device table. This results in the device compatible "of:NvpuT<NULL>Cfsl,imx6q-vpuCcnm,coda960" not matching the module alias "of:N*T*Cfsl,imx6q-vpu" anymore, whereas before commit 2f632369 ("modpost: don't add a trailing wildcard for OF module aliases") it matched the module alias "of:N*T*Cfsl,imx6q-vpu*". This patch adds two module aliases for each compatible, one without the wildcard and one with "C*" appended. $ modinfo coda | grep imx6q alias: of:N*T*Cfsl,imx6q-vpuC* alias: of:N*T*Cfsl,imx6q-vpu Fixes: 2f632369 ("modpost: don't add a trailing wildcard for OF module aliases") Link: http://lkml.kernel.org/r/1462203339-15340-1-git-send-email-p.zabel@pengutronix.deSigned-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Cc: Javier Martinez Canillas <javier@osg.samsung.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Eric W. Biederman authored
commit 5ec0811d upstream. When the first propgated copy was a slave the following oops would result: > BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 > IP: [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0 > PGD bacd4067 PUD bac66067 PMD 0 > Oops: 0000 [#1] SMP > Modules linked in: > CPU: 1 PID: 824 Comm: mount Not tainted 4.6.0-rc5userns+ #1523 > Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007 > task: ffff8800bb0a8000 ti: ffff8800bac3c000 task.ti: ffff8800bac3c000 > RIP: 0010:[<ffffffff811fba4e>] [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0 > RSP: 0018:ffff8800bac3fd38 EFLAGS: 00010283 > RAX: 0000000000000000 RBX: ffff8800bb77ec00 RCX: 0000000000000010 > RDX: 0000000000000000 RSI: ffff8800bb58c000 RDI: ffff8800bb58c480 > RBP: ffff8800bac3fd48 R08: 0000000000000001 R09: 0000000000000000 > R10: 0000000000001ca1 R11: 0000000000001c9d R12: 0000000000000000 > R13: ffff8800ba713800 R14: ffff8800bac3fda0 R15: ffff8800bb77ec00 > FS: 00007f3c0cd9b7e0(0000) GS:ffff8800bfb00000(0000) knlGS:0000000000000000 > CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > CR2: 0000000000000010 CR3: 00000000bb79d000 CR4: 00000000000006e0 > Stack: > ffff8800bb77ec00 0000000000000000 ffff8800bac3fd88 ffffffff811fbf85 > ffff8800bac3fd98 ffff8800bb77f080 ffff8800ba713800 ffff8800bb262b40 > 0000000000000000 0000000000000000 ffff8800bac3fdd8 ffffffff811f1da0 > Call Trace: > [<ffffffff811fbf85>] propagate_mnt+0x105/0x140 > [<ffffffff811f1da0>] attach_recursive_mnt+0x120/0x1e0 > [<ffffffff811f1ec3>] graft_tree+0x63/0x70 > [<ffffffff811f1f6b>] do_add_mount+0x9b/0x100 > [<ffffffff811f2c1a>] do_mount+0x2aa/0xdf0 > [<ffffffff8117efbe>] ? strndup_user+0x4e/0x70 > [<ffffffff811f3a45>] SyS_mount+0x75/0xc0 > [<ffffffff8100242b>] do_syscall_64+0x4b/0xa0 > [<ffffffff81988f3c>] entry_SYSCALL64_slow_path+0x25/0x25 > Code: 00 00 75 ec 48 89 0d 02 22 22 01 8b 89 10 01 00 00 48 89 05 fd 21 22 01 39 8e 10 01 00 00 0f 84 e0 00 00 00 48 8b 80 d8 00 00 00 <48> 8b 50 10 48 89 05 df 21 22 01 48 89 15 d0 21 22 01 8b 53 30 > RIP [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0 > RSP <ffff8800bac3fd38> > CR2: 0000000000000010 > ---[ end trace 2725ecd95164f217 ]--- This oops happens with the namespace_sem held and can be triggered by non-root users. An all around not pleasant experience. To avoid this scenario when finding the appropriate source mount to copy stop the walk up the mnt_master chain when the first source mount is encountered. Further rewrite the walk up the last_source mnt_master chain so that it is clear what is going on. The reason why the first source mount is special is that it it's mnt_parent is not a mount in the dest_mnt propagation tree, and as such termination conditions based up on the dest_mnt mount propgation tree do not make sense. To avoid other kinds of confusion last_dest is not changed when computing last_source. last_dest is only used once in propagate_one and that is above the point of the code being modified, so changing the global variable is meaningless and confusing. fixes: f2ebb3a9 ("smarter propagate_mnt()") Reported-by:
Tycho Andersen <tycho.andersen@canonical.com> Reviewed-by:
Seth Forshee <seth.forshee@canonical.com> Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Dan Streetman authored
commit 32a4e169 upstream. Instead of using "zswap" as the name for all zpools created, add an atomic counter and use "zswap%x" with the counter number for each zpool created, to provide a unique name for each new zpool. As zsmalloc, one of the zpool implementations, requires/expects a unique name for each pool created, zswap should provide a unique name. The zsmalloc pool creation does not fail if a new pool with a conflicting name is created, unless CONFIG_ZSMALLOC_STAT is enabled; in that case, zsmalloc pool creation fails with -ENOMEM. Then zswap will be unable to change its compressor parameter if its zpool is zsmalloc; it also will be unable to change its zpool parameter back to zsmalloc, if it has any existing old zpool using zsmalloc with page(s) in it. Attempts to change the parameters will result in failure to create the zpool. This changes zswap to provide a unique name for each zpool creation. Fixes: f1c54846 ("zswap: dynamic pool creation") Signed-off-by:
Dan Streetman <ddstreet@ieee.org> Reported-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by:
-
Hugh Dickins authored
commit 14af4a5e upstream. /proc/sys/vm/stat_refresh warns nr_isolated_anon and nr_isolated_file go increasingly negative under compaction: which would add delay when should be none, or no delay when should delay. The bug in compaction was due to a recent mmotm patch, but much older instance of the bug was also noticed in isolate_migratepages_range() which is used for CMA and gigantic hugepage allocations. The bug is caused by putback_movable_pages() in an error path decrementing the isolated counters without them being previously incremented by acct_isolated(). Fix isolate_migratepages_range() by removing the error-path putback, thus reaching acct_isolated() with migratepages still isolated, and leaving putback to caller like most other places do. Fixes: edc2ca61 ("mm, compaction: move pageblock checks up from isolate_migratepages_range()") [vbabka@suse.cz: expanded the changelog] Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
Vlastimil Babka <vbabka@suse.cz> Acked-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by:
-
Johannes Weiner authored
commit 4550c4e1 upstream. Cgroup2 currently doesn't have a per-cgroup swappiness setting. We might want to add one later - that's a different discussion - but until we do, the cgroups should always follow the system setting. Otherwise it will be unchangeably set to whatever the ancestor inherited from the system setting at the time of cgroup creation. Signed-off-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by:
-
Linus Torvalds authored
commit 689de1d6 upstream. This is a fairly minimal fixup to the horribly bad behavior of hash_64() with certain input patterns. In particular, because the multiplicative value used for the 64-bit hash was intentionally bit-sparse (so that the multiply could be done with shifts and adds on architectures without hardware multipliers), some bits did not get spread out very much. In particular, certain fairly common bit ranges in the input (roughly bits 12-20: commonly with the most information in them when you hash things like byte offsets in files or memory that have block factors that mean that the low bits are often zero) would not necessarily show up much in the result. There's a bigger patch-series brewing to fix up things more completely, but this is the fairly minimal fix for the 64-bit hashing problem. It simply picks a much better constant multiplier, spreading the bits out a lot better. NOTE! For 32-bit architectures, the bad old hash_64() remains the same for now, since 64-bit multiplies are expensive. The bigger hashing cleanup will replace the 32-bit case with something better. The new constants were picked by George Spelvin who wrote that bigger cleanup series. I just picked out the constants and part of the comment from that series. Cc: George Spelvin <linux@horizon.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Shaohua Li authored
commit 9c573de3 upstream. blk_queue_split marks bio unmergeable, which makes sense for normal bio. But if dispatching the bio to underlayer disk, the blk_queue_split checks are invalid, hence it's possible the bio becomes mergeable. In the reported bug, this bug causes trim against raid0 performance slash https://bugzilla.kernel.org/show_bug.cgi?id=117051Reported-and-tested-by:
Park Ju Hyung <qkrwngud825@gmail.com> Fixes: 6ac45aeb(block: avoid to merge splitted bio) Cc: Ming Lei <ming.lei@canonical.com> Cc: Neil Brown <neilb@suse.de> Reviewed-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
