- 13 Nov, 2015 30 commits
-
-
Daniel Vetter authored
commit 621bd0f6 upstream. With atomic drivers we need to make sure that (at least in general) property reads hold the right locks. But the legacy dpms property is special and can be read locklessly. Since userspace loves to just randomly look at that all the time (like with "status") do that. To make it clear that we play tricks use the READ_ONCE compiler barrier (and also for paranoia). Note that there's not really anything bad going on since even with the new atomic paths we eventually end up not chasing any pointers (and hence possibly freed memory and other fun stuff). The locking WARNING has been added in commit 88a48e29 Author: Rob Clark <robdclark@gmail.com> Date: Thu Dec 18 16:01:50 2014 -0500 drm: add atomic properties but since drivers are converting not everyone will have seen this from the start. Jens reported this and submitted a patch to just grab the mode_config.connection_mutex, but we can do a bit better. v2: Remove unused variables I failed to git add for real. Reference: http://mid.gmane.org/20150928194822.GA3930@kernel.dkReported-by:
Jens Axboe <axboe@fb.com> Tested-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Dave Kleikamp authored
commit a66d7f72 upstream. Some of the crypto algorithms write to the initialization vector, but no space has been allocated for it. This clobbers adjacent memory. Signed-off-by:
Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Christophe Lombard authored
commit 4108efb0 upstream. The scheduled process area is currently allocated before assigning the correct maximum processes to the AFU, which will mean we only ever allocate a fixed number of pages for the scheduled process area. This will limit us to 958 processes with 2 x 64K pages. If we try to use more processes than that we'd probably overrun the buffer and corrupt memory or crash. AFUs that require three or more interrupts per process will not be affected as they are already limited to less processes than that, but we could hit it on an AFU that requires 0, 1 or 2 interrupts per process, or when using 4K pages. This patch moves the initialisation of the num_procs to before the SPA allocation so that enough pages will be allocated for the number of processes that the AFU supports. Signed-off-by:
Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by:
Ian Munsie <imunsie@au1.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Alex Deucher authored
commit 51a4726b upstream. They were added relatively early in the driver init process which meant that in some cases the driver was not finished initializing before external tools tried to use them which could result in a crash depending on the timing. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Shaohua Li authored
commit 874bbfe6 upstream. My system keeps crashing with below message. vmstat_update() schedules a delayed work in current cpu and expects the work runs in the cpu. schedule_delayed_work() is expected to make delayed work run in local cpu. The problem is timer can be migrated with NO_HZ. __queue_work() queues work in timer handler, which could run in a different cpu other than where the delayed work is scheduled. The end result is the delayed work runs in different cpu. The patch makes __queue_delayed_work records local cpu earlier. Where the timer runs doesn't change where the work runs with the change. [ 28.010131] ------------[ cut here ]------------ [ 28.010609] kernel BUG at ../mm/vmstat.c:1392! [ 28.011099] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [ 28.011860] Modules linked in: [ 28.012245] CPU: 0 PID: 289 Comm: kworker/0:3 Tainted: G W4.3.0-rc3+ #634 [ 28.013065] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153802- 04/01/2014 [ 28.014160] Workqueue: events vmstat_update [ 28.014571] task: ffff880117682580 ti: ffff8800ba428000 task.ti: ffff8800ba428000 [ 28.015445] RIP: 0010:[<ffffffff8115f921>] [<ffffffff8115f921>]vmstat_update+0x31/0x80 [ 28.016282] RSP: 0018:ffff8800ba42fd80 EFLAGS: 00010297 [ 28.016812] RAX: 0000000000000000 RBX: ffff88011a858dc0 RCX:0000000000000000 [ 28.017585] RDX: ffff880117682580 RSI: ffffffff81f14d8c RDI:ffffffff81f4df8d [ 28.018366] RBP: ffff8800ba42fd90 R08: 0000000000000001 R09:0000000000000000 [ 28.019169] R10: 0000000000000000 R11: 0000000000000121 R12:ffff8800baa9f640 [ 28.019947] R13: ffff88011a81e340 R14: ffff88011a823700 R15:0000000000000000 [ 28.020071] FS: 0000000000000000(0000) GS:ffff88011a800000(0000)knlGS:0000000000000000 [ 28.020071] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 28.020071] CR2: 00007ff6144b01d0 CR3: 00000000b8e93000 CR4:00000000000006f0 [ 28.020071] Stack: [ 28.020071] ffff88011a858dc0 ffff8800baa9f640 ffff8800ba42fe00ffffffff8106bd88 [ 28.020071] ffffffff8106bd0b 0000000000000096 0000000000000000ffffffff82f9b1e8 [ 28.020071] ffffffff829f0b10 0000000000000000 ffffffff81f18460ffff88011a81e340 [ 28.020071] Call Trace: [ 28.020071] [<ffffffff8106bd88>] process_one_work+0x1c8/0x540 [ 28.020071] [<ffffffff8106bd0b>] ? process_one_work+0x14b/0x540 [ 28.020071] [<ffffffff8106c214>] worker_thread+0x114/0x460 [ 28.020071] [<ffffffff8106c100>] ? process_one_work+0x540/0x540 [ 28.020071] [<ffffffff81071bf8>] kthread+0xf8/0x110 [ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200 [ 28.020071] [<ffffffff81a6522f>] ret_from_fork+0x3f/0x70 [ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200 Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Christoph Hellwig authored
commit 15e3d5a2 upstream. 3w controller don't dma map small single SGL entry commands but instead bounce buffer them. Add a helper to identify these commands and don't call scsi_dma_unmap for them. Based on an earlier patch from James Bottomley. Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by:
Tóth Attila <atoth@atoth.sote.hu> Tested-by:
Christoph Hellwig <hch@lst.de> Acked-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Joe Thornber authored
commit 2bffa150 upstream. The cleaner policy doesn't make use of the per cache block hint space in the metadata (unlike the other policies). When switching from the cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block) was observed. The crash was caused by bugs in dm-cache-metadata.c when trying to skip creation of the hint btree. The minimal fix is to change hint size for the cleaner policy to 4 bytes (only hint size supported). Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
commit 95913d97 upstream. So the problem this patch is trying to address is as follows: CPU0 CPU1 context_switch(A, B) ttwu(A) LOCK A->pi_lock A->on_cpu == 0 finish_task_switch(A) prev_state = A->state <-. WMB | A->on_cpu = 0; | UNLOCK rq0->lock | | context_switch(C, A) `-- A->state = TASK_DEAD prev_state == TASK_DEAD put_task_struct(A) context_switch(A, C) finish_task_switch(A) A->state == TASK_DEAD put_task_struct(A) The argument being that the WMB will allow the load of A->state on CPU0 to cross over and observe CPU1's store of A->state, which will then result in a double-drop and use-after-free. Now the comment states (and this was true once upon a long time ago) that we need to observe A->state while holding rq->lock because that will order us against the wakeup; however the wakeup will not in fact acquire (that) rq->lock; it takes A->pi_lock these days. We can obviously fix this by upgrading the WMB to an MB, but that is expensive, so we'd rather avoid that. The alternative this patch takes is: smp_store_release(&A->on_cpu, 0), which avoids the MB on some archs, but not important ones like ARM. Reported-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: manfred@colorfullife.com Cc: will.deacon@arm.com Fixes: e4a52bcb ("sched: Remove rq->lock from the first half of ttwu()") Link: http://lkml.kernel.org/r/20150929124509.GG3816@twins.programming.kicks-ass.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Andreas Dannenberg authored
commit e2600460 upstream. The minimum volume level for the TAS2552 (control register value 0x00) is -7dB however the driver declares it as -0.07dB. Running amixer before the patch reports: dBscale-min=-0.07dB,step=1.00dB,mute=0 Running amixer with the patch applied reports: dBscale-min=-7.00dB,step=1.00dB,mute=0 Signed-off-by:
Andreas Dannenberg <dannenberg@ti.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Peter Ujfalusi authored
commit dd6ae3bc upstream. The last parameter for DECLARE_TLV_DB_SCALE() is to tell if the gain will be muted or not when it is set to raw 0. IN this case it is not muted. The PGA_GAIN is in 0-4 bits in the register. Fix the offset in the SOC_SINGLE_TLV() for this. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Mark Salyzyn authored
commit 569ba74a upstream. This is the arm64 portion of commit 45cac65b ("readahead: fault retry breaks mmap file read random detection"), which was absent from the initial port and has since gone unnoticed. The original commit says: > .fault now can retry. The retry can break state machine of .fault. In > filemap_fault, if page is miss, ra->mmap_miss is increased. In the second > try, since the page is in page cache now, ra->mmap_miss is decreased. And > these are done in one fault, so we can't detect random mmap file access. > > Add a new flag to indicate .fault is tried once. In the second try, skip > ra->mmap_miss decreasing. The filemap_fault state machine is ok with it. With this change, Mark reports that: > Random read improves by 250%, sequential read improves by 40%, and > random write by 400% to an eMMC device with dm crypto wrapped around it. Cc: Shaohua Li <shli@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
Mark Salyzyn <salyzyn@android.com> Signed-off-by:
Riley Andrews <riandrews@android.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Takashi Iwai authored
commit 225db576 upstream. When OSS emulation is loaded on ISA SB AWE32 chip, we get now kernel warnings like: WARNING: CPU: 0 PID: 2791 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x51/0x80() sysfs: cannot create duplicate filename '/devices/isa/sbawe.0/sound/card0/seq-oss-0-0' It's because both emux synth and opl3 drivers try to register their OSS device object with the same static index number 0. This hasn't been a big problem until the recent rewrite of device management code (that exposes sysfs at the same time), but it's been an obvious bug. This patch works around it just by using a different index number of emux synth object. There can be a more elegant way to fix, but it's enough for now, as this code won't be touched so often, in anyway. Reported-and-tested-by:
Michael Shell <list1@michaelshell.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
covici@ccs.covici.com authored
commit b1d562ac upstream. Here is a patch to make speakup-r work again. It broke in 3.6 due to commit 4369c64c "Input: Send events one packet at a time) The problem was that the fakekey.c routine to fake a down arrow no longer functioned properly and putting the input_sync fixed it. Fixes: 4369c64cAcked-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by:
John Covici <covici@ccs.covici.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Jann Horn authored
commit 0c556271 upstream. This is mostly a hardening fix, given that write-only access to other users' ttys is usually only given through setgid tty executables. Signed-off-by:
Jann Horn <jann@thejh.net> Signed-off-by:
-
Mans Rullgard authored
commit 3c5a0357 upstream. This adds an entry to the uart_config table for PORT_RT2880 enabling rx/tx FIFOs. The UART is actually a Palmchip BK-3103 which is found in several devices from Alchemy/RMI, Ralink, and Sigma Designs. Signed-off-by:
Mans Rullgard <mans@mansr.com> Signed-off-by:
-
Kosuke Tatsukawa authored
commit e81107d4 upstream. My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 #1 [ffff88303d107bd0] schedule at ffffffff815c513e #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 #5 [ffff88303d107dd0] tty_read at ffffffff81368013 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 #8 [ffff88303d107f00] sys_read at ffffffff811a4306 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by:
Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Signed-off-by:
-
Vincent Palatin authored
commit 72194739 upstream. Add a device quirk for the Logitech PTZ Pro Camera and its sibling the ConferenceCam CC3000e Camera. This fixes the failed camera enumeration on some boot, particularly on machines with fast CPU. Tested by connecting a Logitech PTZ Pro Camera to a machine with a Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles while recording the kernel logs and taking camera picture after each boot. Before the patch, more than 7% of the boots show some enumeration transfer failures and in a few of them, the kernel is giving up before actually enumerating the webcam. After the patch, the enumeration has been correct on every reboot. Signed-off-by:
Vincent Palatin <vpalatin@chromium.org> Signed-off-by:
-
Yao-Wen Mao authored
commit 8484bf29 upstream. These two headphones need a reset-resume quirk to properly resume to original volume level. Signed-off-by:
Yao-Wen Mao <yaowen@google.com> Signed-off-by:
-
John Flatness authored
commit e8ff581f upstream. The MacBookPro 12,1 has the same setup as the 11 for controlling the status of the optical audio light. Simply apply the existing workaround to the subsystem ID for the 12,1. [sorted the fixup entry by tiwai] Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105401Signed-off-by:
John Flatness <john@zerocrates.org> Signed-off-by:
-
Laura Abbott authored
commit d05ea7da upstream. Much like all the other Lenovo laptops, add a quirk to make sound work with docking. Reported-and-tested-by: lacknerflo@gmail.com Signed-off-by:
Laura Abbott <labbott@fedoraproject.org> Signed-off-by:
-
Mikulas Patocka authored
commit 042745ee upstream. Commit 3a0f9aae ("dm raid: round region_size to power of two") intended to make sure that the default region size is a power of two. However, the logic in that commit is incorrect and sets the variable region_size to 0 or 1, depending on whether min_region_size is a power of two. Fix this logic, using roundup_pow_of_two(), so that region_size is properly rounded up to the next power of two. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Fixes: 3a0f9aae ("dm raid: round region_size to power of two") Signed-off-by:
-
Yitian Bu authored
commit 4873867e upstream. from Designware I2S datasheet, tx/rx XRUN irq is cleared by reading register TOR/ROR, rather than by writing into them. Signed-off-by:
Yitian Bu <yitian.bu@tangramtek.com> Signed-off-by:
-
Ben Dooks authored
commit 19e79687 upstream. On the OMAP AM3517 platform the uart4_ick gets registered twice, causing any power management to /dev/ttyO3 to fail when trying to wake the device up. This solves the following oops: [] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008 [] PC is at serial_omap_pm+0x48/0x15c [] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c Fixes: aafd900c ("CLK: TI: add omap3 clock init file") Cc: mturquette@baylibre.com Cc: sboyd@codeaurora.org Cc: linux-clk@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-kernel@lists.codethink.co.uk Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by:
Tero Kristo <t-kristo@ti.com> Signed-off-by:
-
Steve French authored
commit 646200a0 upstream. The error paths in set_file_size for cifs and smb3 are incorrect. In the unlikely event that a server did not support set file info of the file size, the code incorrectly falls back to trying SMBWriteX (note that only the original core SMB Write, used for example by DOS, can set the file size this way - this actually does not work for the more recent SMBWriteX). The idea was since the old DOS SMB Write could set the file size if you write zero bytes at that offset then use that if server rejects the normal set file info call. Fortunately the SMBWriteX will never be sent on the wire (except when file size is zero) since the length and offset fields were reversed in the two places in this function that call SMBWriteX causing the fall back path to return an error. It is also important to never call an SMB request from an SMB2/sMB3 session (which theoretically would be possible, and can cause a brief session drop, although the client recovers) so this should be fixed. In practice this path does not happen with modern servers but the error fall back to SMBWriteX is clearly wrong. Removing the calls to SMBWriteX in the error paths in cifs_set_file_size Pointed out by PaX/grsecurity team Signed-off-by:
Steve French <steve.french@primarydata.com> Reported-by:
PaX Team <pageexec@freemail.hu> CC: Emese Revfy <re.emese@gmail.com> CC: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Junichi Nomura authored
commit 2a708cff upstream. __dm_destroy() takes io_barrier SRCU lock (dm_get_live_table) and suspend_lock in reverse order. Doing so can cause AB-BA deadlock: __dm_destroy dm_swap_table --------------------------------------------------- mutex_lock(suspend_lock) dm_get_live_table() srcu_read_lock(io_barrier) dm_sync_table() synchronize_srcu(io_barrier) .. waiting for dm_put_live_table() mutex_lock(suspend_lock) .. waiting for suspend_lock Fix this by taking the locks in proper order. Signed-off-by:
Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Fixes: ab7c7bb6 ("dm: hold suspend_lock while suspending device during device deletion") Acked-by:
-
Gianluca Renzi authored
commit e256da84 upstream. Signed-off-by:
Gianluca Renzi <gianlucarenzi@eurekelettronica.it> Signed-off-by:
-
Steve Wise authored
commit c91aed98 upstream. The server rdma_read_chunk_lcl() and rdma_read_chunk_frmr() functions were not taking into account the initial page_offset when determining the rdma read length. This resulted in a read who's starting address and length exceeded the base/bounds of the frmr. The server gets an async error from the rdma device and kills the connection, and the client then reconnects and resends. This repeats indefinitely, and the application hangs. Most work loads don't tickle this bug apparently, but one test hit it every time: building the linux kernel on a 16 core node with 'make -j 16 O=/mnt/0' where /mnt/0 is a ramdisk mounted via NFSRDMA. This bug seems to only be tripped with devices having small fastreg page list depths. I didn't see it with mlx4, for instance. Fixes: 0bf48289 ('svcrdma: refactor marshalling logic') Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Tested-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Christian Borntraeger authored
commit adc0b7fb upstream. my gcc 5.1 used an ldgr instruction with a register != 0,2,4,6 for spilling/filling into a floating point register in our decompressor. This will cause an AFP-register data exception as the decompressor did not setup the additional floating point registers via cr0. That causes a program check loop that looked like a hang with one "Uncompressing Linux... " message (directly booted via kvm) or a loop of "Uncompressing Linux... " messages (when booted via zipl boot loader). The offending code in my build was 48e400: e3 c0 af ff ff 71 lay %r12,-1(%r10) -->48e406: b3 c1 00 1c ldgr %f1,%r12 48e40a: ec 6c 01 22 02 7f clij %r6,2,12,0x48e64e but gcc could do spilling into an fpr at any function. We can simply disable floating point support at that early stage. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Acked-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Malcolm Crossley authored
commit 64c98e7f upstream. Sanitizing the e820 map may produce extra E820 entries which would result in the topmost E820 entries being removed. The removed entries would typically include the top E820 usable RAM region and thus result in the domain having signicantly less RAM available to it. Fix by allowing sanitize_e820_map to use the full size of the allocated E820 array. Signed-off-by:
Malcolm Crossley <malcolm.crossley@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> [ kamal: backport to 3.19-stable: context ] Signed-off-by:
-
Vitaly Kuznetsov authored
commit 0b34a166 upstream. Currently there is a number of issues preventing PVHVM Xen guests from doing successful kexec/kdump: - Bound event channels. - Registered vcpu_info. - PIRQ/emuirq mappings. - shared_info frame after XENMAPSPACE_shared_info operation. - Active grant mappings. Basically, newly booted kernel stumbles upon already set up Xen interfaces and there is no way to reestablish them. In Xen-4.7 a new feature called 'soft reset' is coming. A guest performing kexec/kdump operation is supposed to call SCHEDOP_shutdown hypercall with SHUTDOWN_soft_reset reason before jumping to new kernel. Hypervisor (with some help from toolstack) will do full domain cleanup (but keeping its memory and vCPU contexts intact) returning the guest to the state it had when it was first booted and thus allowing it to start over. Doing SHUTDOWN_soft_reset on Xen hypervisors which don't support it is probably OK as by default all unknown shutdown reasons cause domain destroy with a message in toolstack log: 'Unknown shutdown reason code 5. Destroying domain.' which gives a clue to what the problem is and eliminates false expectations. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
- 12 Nov, 2015 10 commits
-
-
Lars-Peter Clausen authored
commit e74679b3 upstream. Commit b4508d0f ("ASoC: db1200: Use static DAI format setup") switched the db1200 driver over to using static DAI format setup instead of a callback function. But the commit only added the dai_fmt field to one of the three DAI links in the driver. This breaks audio on db1300 and db1550. Add the two missing dai_fmt settings to fix the issue. Fixes: b4508d0f ("ASoC: db1200: Use static DAI format setup") Reported-by:
Manuel Lauss <manuel.lauss@gmail.com> Tested-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Felipe F. Tonello authored
commit 0af82211 upstream. This fixes a duplicated pin control causing this error: imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already requested by regulators:regulator@2; cannot claim for 2184000.usb imx6q-pinctrl 20e0000.iomuxc: pin-137 (2184000.usb) status -22 imx6q-pinctrl 20e0000.iomuxc: could not request pin 137 (MX6Q_PAD_GPIO_1) from group usbotggrp on device 20e0000.iomuxc imx_usb 2184000.usb: Error applying setting, reverse things back imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_EIM_D31 already requested by regulators:regulator@1; cannot claim for 2184200.usb imx6q-pinctrl 20e0000.iomuxc: pin-52 (2184200.usb) status -22 imx6q-pinctrl 20e0000.iomuxc: could not request pin 52 (MX6Q_PAD_EIM_D31) from group usbh1grp on device 20e0000.iomuxc imx_usb 2184200.usb: Error applying setting, reverse things back Signed-off-by:
Felipe F. Tonello <eu@felipetonello.com> Fixes: e2047e33 ("ARM: dts: add initial Rex Pro board support") Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Boris BREZILLON authored
commit 8e375ccd upstream. The sunxi_nand_chips_cleanup() function is missing a call to list_del() which generates a double free error. Reported-by:
Priit Laes <plaes@plaes.org> Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: 1fef62c1 ("mtd: nand: add sunxi NAND flash controller support") Tested-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Boris BREZILLON authored
commit 03a0e8a7 upstream. The USER_DATA register cannot be accessed using byte accessors on A13 SoCs, thus triggering a bug when using memcpy_toio on this register. Declare an helper macros to convert an OOB buffer into a suitable USER_DATA value and vice-versa. This patch also fixes an error in the oob_required logic (some OOB data are not written even if the user required it) by removing the oob_required condition, which is perfectly valid since the core already fill ->oob_poi with FFs when oob_required is false. Signed-off-by:
-
Mark Brown authored
commit 176fc2d5 upstream. The in kernel snprintf() will conveniently return the actual length of the printed string even if not given an output beffer at all so just do that rather than relying on the user to pass in a suitable buffer, ensuring that we don't need to worry if the buffer was truncated due to the size of the buffer passed in. Reported-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Mark Brown authored
commit b763ec17 upstream. If a read is attempted which is smaller than the line length then we may underflow the subtraction we're doing with the unsigned size_t type so move some of the calculation to be additions on the right hand side instead in order to avoid this. Reported-by:
-
Joonsoo Kim authored
commit 03a2d2a3 upstream. Commit description is copied from the original post of this bug: http://comments.gmane.org/gmane.linux.kernel.mm/135349 Kernels after v3.9 use kmalloc_size(INDEX_NODE + 1) to get the next larger cache size than the size index INDEX_NODE mapping. In kernels 3.9 and earlier we used malloc_sizes[INDEX_L3 + 1].cs_size. However, sometimes we can't get the right output we expected via kmalloc_size(INDEX_NODE + 1), causing a BUG(). The mapping table in the latest kernel is like: index = {0, 1, 2 , 3, 4, 5, 6, n} size = {0, 96, 192, 8, 16, 32, 64, 2^n} The mapping table before 3.10 is like this: index = {0 , 1 , 2, 3, 4 , 5 , 6, n} size = {32, 64, 96, 128, 192, 256, 512, 2^(n+3)} The problem on my mips64 machine is as follows: (1) When configured DEBUG_SLAB && DEBUG_PAGEALLOC && DEBUG_LOCK_ALLOC && DEBUG_SPINLOCK, the sizeof(struct kmem_cache_node) will be "150", and the macro INDEX_NODE turns out to be "2": #define INDEX_NODE kmalloc_index(sizeof(struct kmem_cache_node)) (2) Then the result of kmalloc_size(INDEX_NODE + 1) is 8. (3) Then "if(size >= kmalloc_size(INDEX_NODE + 1)" will lead to "size = PAGE_SIZE". (4) Then "if ((size >= (PAGE_SIZE >> 3))" test will be satisfied and "flags |= CFLGS_OFF_SLAB" will be covered. (5) if (flags & CFLGS_OFF_SLAB)" test will be satisfied and will go to "cachep->slabp_cache = kmalloc_slab(slab_size, 0u)", and the result here may be NULL while kernel bootup. (6) Finally,"BUG_ON(ZERO_OR_NULL_PTR(cachep->slabp_cache));" causes the BUG info as the following shows (may be only mips64 has this problem): This patch fixes the problem of kmalloc_size(INDEX_NODE + 1) and removes the BUG by adding 'size >= 256' check to guarantee that all necessary small sized slabs are initialized regardless sequence of slab size in mapping table. Fixes: e3366016 ("slab: Use common kmalloc_index/kmalloc_size...") Signed-off-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by:
Liuhailong <liu.hailong6@zte.com.cn> Acked-by:
Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Andy Shevchenko authored
commit 6bea0f6d upstream. In case we have less than maximum allowed channels (8) and autoconfiguration is enabled the DWC_PARAMS read is wrong because it uses different arithmetic to what is needed for channel priority setup. Re-do the caclulations properly. This now works on AVR32 board well. Fixes: fed2574b (dw_dmac: introduce software emulation of LLP transfers) Cc: yitian.bu@tangramtek.com Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
John Stultz authored
commit 67dfae0c upstream. This patch fixes one cases where abs() was being used with 64-bit nanosecond values, where the result may be capped at 32-bits. This potentially could cause watchdog false negatives on 32-bit systems, so this patch addresses the issue by using abs64(). Signed-off-by:
John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Li Bin authored
commit ee556d00 upstream. When function graph tracer is enabled, the following operation will trigger panic: mount -t debugfs nodev /sys/kernel echo next_tgid > /sys/kernel/tracing/set_ftrace_filter echo function_graph > /sys/kernel/tracing/current_tracer ls /proc/ ------------[ cut here ]------------ [ 198.501417] Unable to handle kernel paging request at virtual address cb88537fdc8ba316 [ 198.506126] pgd = ffffffc008f79000 [ 198.509363] [cb88537fdc8ba316] *pgd=00000000488c6003, *pud=00000000488c6003, *pmd=0000000000000000 [ 198.517726] Internal error: Oops: 94000005 [#1] SMP [ 198.518798] Modules linked in: [ 198.520582] CPU: 1 PID: 1388 Comm: ls Tainted: G [ 198.521800] Hardware name: linux,dummy-virt (DT) [ 198.522852] task: ffffffc0fa9e8000 ti: ffffffc0f9ab0000 task.ti: ffffffc0f9ab0000 [ 198.524306] PC is at next_tgid+0x30/0x100 [ 198.525205] LR is at return_to_handler+0x0/0x20 [ 198.526090] pc : [<ffffffc0002a1070>] lr : [<ffffffc0000907c0>] pstate: 60000145 [ 198.527392] sp : ffffffc0f9ab3d40 [ 198.528084] x29: ffffffc0f9ab3d40 x28: ffffffc0f9ab0000 [ 198.529406] x27: ffffffc000d6a000 x26: ffffffc000b786e8 [ 198.530659] x25: ffffffc0002a1900 x24: ffffffc0faf16c00 [ 198.531942] x23: ffffffc0f9ab3ea0 x22: 0000000000000002 [ 198.533202] x21: ffffffc000d85050 x20: 0000000000000002 [ 198.534446] x19: 0000000000000002 x18: 0000000000000000 [ 198.535719] x17: 000000000049fa08 x16: ffffffc000242efc [ 198.537030] x15: 0000007fa472b54c x14: ffffffffff000000 [ 198.538347] x13: ffffffc0fada84a0 x12: 0000000000000001 [ 198.539634] x11: ffffffc0f9ab3d70 x10: ffffffc0f9ab3d70 [ 198.540915] x9 : ffffffc0000907c0 x8 : ffffffc0f9ab3d40 [ 198.542215] x7 : 0000002e330f08f0 x6 : 0000000000000015 [ 198.543508] x5 : 0000000000000f08 x4 : ffffffc0f9835ec0 [ 198.544792] x3 : cb88537fdc8ba316 x2 : cb88537fdc8ba306 [ 198.546108] x1 : 0000000000000002 x0 : ffffffc000d85050 [ 198.547432] [ 198.547920] Process ls (pid: 1388, stack limit = 0xffffffc0f9ab0020) [ 198.549170] Stack: (0xffffffc0f9ab3d40 to 0xffffffc0f9ab4000) [ 198.582568] Call trace: [ 198.583313] [<ffffffc0002a1070>] next_tgid+0x30/0x100 [ 198.584359] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.585503] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.586574] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.587660] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.588896] Code: aa0003f5 2a0103f4 b4000102 91004043 (885f7c60) [ 198.591092] ---[ end trace 6a346f8f20949ac8 ]--- This is because when using function graph tracer, if the traced function return value is in multi regs ([x0-x7]), return_to_handler may corrupt them. So in return_to_handler, the parameter regs should be protected properly. Signed-off-by:
Li Bin <huawei.libin@huawei.com> Acked-by:
AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
