Skip to content

L
linux
Switch branch/tag
  1. 07 Jun, 2004 13 commits
    • David Brownell's avatar
      [PATCH] USB: rndis (1/4) update OID support · e9bcd70c
      David Brownell authored 
      NDIS devices have a generic attribute get/set API where the attributes
are identified by 32 bit "OIDs".  This fixes some problems with the OIDs
supported by the original RNDIS patch:

  - It included OIDs not found in the RNDIS spec.  These have been
    removed.  As a rule, these weren't exported in the "OIDs I support"
    list, and only a couple wouldn't fail those accesses, so this mostly
    changes what debug printk appears.

  - OIDs used for optional 802.3 statistics were partially supported.
    They're all in the OID list now, but the support is #ifdeffed out.
    (Those statistics were mostly just made up, anyway!)

  - "Required" OIDs for suspend, resume, and wakeup support weren't
    listed.  Their messages are now defined, but support is #ifdeffed
    out.  Seems the docs aren't entirely accurate, and Windows can
    behave reasonably without them.  (This area needs help from someone
    who knows MS-Windows power management.)

There are also a few minor cleanups, more reasonable default volume level
for debug messages (never at KERN_INFO, keepalives only if VERBOSE), and
dumping of all bytes of some undocumented messages Windows XP has been
seen emitting shortly before the host suspended itself.
Signed-off-by: default avatarDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      e9bcd70c
    • Alan Stern's avatar
      [PATCH] USB: unusual_devs.h update · 5d14ffeb
      Alan Stern authored 
      Given the problems that Dan Scholnik has reported, we should combine the
unusual_devs.h entries for the Casio QV cameras into one.  The new
NEED_OVERRIDE flag will prevent complaints about unnecessary overrides,
and Dan says the same subclass and protocol values should work for all the
cameras.  If they don't we'll hear about it soon enough!


On Tue, 1 Jun 2004, Dan Scholnik wrote:
> On Tue, 2004-06-01 at 14:14, Alan Stern wrote:
> > On Tue, 1 Jun 2004, Dan Scholnik wrote:
> >
> > > Up until the 2.6 kernels, there was one entry for all the QV cameras
> > > with both US_SC_8070 and US_PR_CB that I think seemed to work fine for
> > > everyone.  As far as I know the only problem was all the folks emailing
> > > the log entry stating that the Casio entry wasn't needed.  So, you could
> > > revert back to that, or revert back to the 2.6.3ish version (pre-as190)
> > > that had the overrides just for product IDs 1001-9009.  I'm not really
> > > an expert on Casio's cameras, I'm afraid, just the one model I own which
> > > is 4-5 years old now.
> > >
> > > I'll be happy to prepare a patch any way you choose to go.
> >
> > How does this work for you?
> >
> > Alan Stern
>
> Works fine for me; that's I think exactly how it was from the beginning
> until 2.6 and the later 2.4 kernels when all the changes were made.
> Just cross your fingers that it doesn't somehow break newer Casios, as
> it would seem every camera they ever made falls under that entry.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      5d14ffeb
    • Alan Stern's avatar
      [PATCH] USB: Fix resource leakage in the hub driver · 729f806b
      Alan Stern authored 
      The hub driver is very careless about returning resources when an error
occurs while installing a new device.  This patch attempts to put some
order back into the situation.  Details:

	Since usb_new_device() allocates neither the device structure
	nor the device address, it shouldn't release either one.

	Because usb_new_device() no longer releases the device structure,
	usb_register_root_hub() doesn't need to take an extra reference
	to it.

	Since the device address selection and TT setup code is used
	only for new devices, not ones being reset, move that code from
	hub_port_init() to hub_port_connect_change().  By the same token,
	hub_port_init() doesn't have to release the device address or
	the device structure.

	Just to make things look better, move the failure code in
	hub_port_init() to the end of the routine.  And when disabling
	endpoint 0, disable both the IN and OUT parts of the endpoint.

	In hub_port_connect_change(), make all the failure paths
	execute the same code so that resources are always released.
	These resources comprise: the pointer from the parent to the
	new child device, the HCD state for ep0, the device's address,
	and the device structure itself -- in short, everything that's
	set up before calling usb_new_device().
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      729f806b
    • Alan Stern's avatar
      [PATCH] USB: Check port reset return code · 70244527
      Alan Stern authored 
      This patch adds checking for the SET-FEATURE request that actually does a
port reset.  Without the check, the hub driver just assumes that the port
reset command actually was transferred okay.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      70244527
    • Duncan Sands's avatar
      [PATCH] USB devio.c: deadlock fix · 15903813
      Duncan Sands authored 
      proc_resetdevice is called with dev->serialize held.
usb_reset_device takes dev->serialize and then calls
__usb_reset_device.  To avoid deadlock, proc_resetdevice
should call __usb_reset_device directly.
Signed-off-by: default avatarDuncan Sands <baldrick@free.fr>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      15903813
    • Alan Stern's avatar
      [PATCH] USB: Fix logic in usb_get_descriptor() · 945fef15
      Alan Stern authored 
      This patch fixes a simple logic error in usb_get_descriptor().  It also
takes the opportunity to make the subroutine a little easier to read.
Please apply.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      945fef15
    • Kai Engert's avatar
      [PATCH] USB: enable pwc usb camera driver · 554b4fbd
      Kai Engert authored 
      The attached patch enables the pwc driver included with kernel 2.6.7-rc2

It also removes the warnings during compilation.
However, note that I blindly duplicated the release approach used by
other usb camera drivers, replacing the current no-op.

The driver works for me with a Logitech QuickCam Notebook Pro and
GnomeMeeting.
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      554b4fbd
    • Matthew Dharm's avatar
      [PATCH] USB Storage: GetMaxLUN tightening · adc625da
      Matthew Dharm authored 
      This patch started life from Alan Stern as as274, and has been heavily
modified.  It narrows the case where a clear_halt() is issued after a
failed GetMaxLUN command to only a STALL case.

Since the only legimate responses to a GetMaxLUN are STALL or data,
anything else is now considered a fatal error and we give up on the device.
Signed-off-by: default avatarMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      adc625da
    • Siegfried Hildebrand's avatar
      [PATCH] Re: Problems with cyberjack usb-serial-module since kernel 2.6.2 · bd504645
      Siegfried Hildebrand authored 
      > Send me a patch to back those changes out to fix your device and I'll
> apply it.  If the author is around to realize this, that should wake
> them up :)

Ok, here you are! :)
Attached is a patch for linux-2.6.7-rc2. (though the patch hasn't changed
since -rc1)

Again a short description:
(the patch removes most of the changes done in linux-2.6.2)
1. Removed the local buffer of cyberjack_write, because something goes wrong
upon a write-request bigger than the buffer. Without this, a write-request
stalls with error -3.
2. Removed some usb_clear_halt() lines. Without this, the device doesn't even
open and returns -7.

It works for my cyberjack pinpad USB card reader on
- nforce2 chipset
- VIA KM266 chipset
- AMD Irongate chipset
Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      bd504645
    • Greg Kroah-Hartman's avatar
      USB: make usb devices remove their sysfs files when disconnected. · a2870c79
      Greg Kroah-Hartman authored 
      Signed-off-by: default avatarGreg Kroah-Hartman <greg@kroah.com>
      a2870c79
    • Greg Kroah-Hartman's avatar
      Merge kroah.com:/home/greg/linux/BK/bleed-2.6 · fcc95bca
      Greg Kroah-Hartman authored 
      into kroah.com:/home/greg/linux/BK/usb-2.6
      fcc95bca
    • Vojtech Pavlik's avatar
      input: Exclude tasklet changes to i8042.c · 501a9693
      Vojtech Pavlik authored 
      Signed-off-by: default avatarVojtech Pavlik <vojtech@suse.cz>
      501a9693
    • Vojtech Pavlik's avatar
      Merge suse.cz:/home/vojtech/bk/linus · 1e12aaf0
      Vojtech Pavlik authored 
      into suse.cz:/home/vojtech/bk/for-linus
      1e12aaf0
  3. 06 Jun, 2004 18 commits
  5. 05 Jun, 2004 9 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7