We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In SiRF platform, there are different fifo size of uart and usp,
with the fifosize configuration changes in different chips, we
can not use port line to decide how to check FIFO full,empty and
level.

There is a direct mapping between FIFO HW register layout with
fifo size, so move to use fifosize as the input to check fifo
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In different platform of SiRF SoCs, there is no same uart and usp-uart
numbers, it is not convenient to use hard-coded ports array and port
lines.

here we drop the hard-coded ports table , and drop "cell-index". then
move to use alias id to get line.

for example:
	aliases {
		serial0 = &uart0;
		serial1 = &uart1;
		serial2 = &uart2;
		serial3 = &uart3;
		serial4 = &uart4;
		serial5 = &uart5;
		serial6 = &uart6;
		serial9 = &usp2;
	};

at the same, enlarge the max port number according to the chip with the most
UART.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add 8250 MTK UART driver to support earlycon device tree.
Earlycon take effect by
  add "earlycon" in kernel boot argument
  add "linux,sdtout-path" property in device tree file
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8250-like uart driver may call early_serial8250_setup to
reuse 8250_early.c character output function.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The mtk 8250 needs two clocks, one for providing the baudrate and
one that needs to be enabled for register accesses. The latter has
not been supported, this patch adds support for it. It is optional
for now since not all SoCs provide a bus clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The pm_runtime callbacks already enable and disable the device.
Use them in probe() and remove() instead of duplicating the
code. This allows us to concentrate more code for enabling/disabling
the UART in a single place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a struct device * is present clk_get should be used rather
than of_clk_get. Use the devm variant of this function to be able to
drop the clk_put in the error and remove pathes. While at it fix
a wrong error message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the driver has probed successfully the clk pointer is always valid,
so no need to test for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function meson_uart_release_port() inappropriately try to
iounmap() a resource managed by devm_ioremap_nocache().
The function meson_uart_release_port() maybe called by uart_ioctl()
that means meson_uart_release_port() is not called from within a
probe or remove function, for safety, I convert iounmap() to
devm_iounmap().
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The rx_running flag should show if DMA is currently active. However
there is a window between when the flag is set/cleared and when
the DMA is started/stopped. Because the flag is queried from both
hard and soft irq contexts, the driver can make incorrect
decisions and do things like start a DMA transfer using a buffer
that is already setup to be used for a DMA transfer.

This patch adds a spinlock to synchronize the rx_running flag and
close the above mentioned window.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8250_omap serial driver relies on dmaengine_pause() actually
pausing the DMA transfer. Before this patch dmaengine_pause() is
a NOP for non-cylic DMA transfers. This allowed the 8250_omap
driver to read DMA buffers while the DMA was still active,
resulting in lost serial data.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When stopping a DMA transfer with interrupts disabled it is possible
that the DMA transfer completes before the events are cleared. In
this case the completion interrupt will be pending, causing a
completion callback after the transfer was stopped.

By clearing the completion interrupt for the stopping channel it is
ensured that no completion event will be generated after the stop.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If NO_DMA=y:

    drivers/built-in.o: In function `ifx_spi_free_device':
    ifx6x60.c:(.text+0x96d9a): undefined reference to `dma_free_coherent'
    drivers/built-in.o: In function `ifx_spi_spi_probe':
    ifx6x60.c:(.text+0x978a2): undefined reference to `dma_alloc_coherent'

While DMA is optional in this driver, and is used only if
ifx_modem_platform_data.use_dma is set, there are currently no in-tree
users of ifx_modem_platform_data (and thus of this driver), so just make
it depend on HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There's no need to cast the last parameter of {request,free}_irq() to
"void *", as any pointer type is accepted.

Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting spi_driver pointers to "void *" when calling
spi_{,un}register_driver() bypasses all type checking.

Remove the superfluous casts to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 52bec4ed("serial: sirf: add a new uart type
support").
we misunderstood the clock dependency in atlas7. Actually involved
several clocks are in a tree structure. we still only need to take
the leaf clock node for BT uarts.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove CONFIG_SERIAL_DETECT_IRQ and CONFIG_SERIAL_MANY_PORTS, and
substitute all references to the proper 8250 Kconfig options.  Now, the
actual Kconfig dependencies are not hidden when reading the code and
static analyzers are less confused.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If CONFIG_SERIAL_CORE_CONSOLE=n, build warnings are generated by
uart_console() macro expansion:

drivers/tty/serial/of_serial.c: In function ‘of_serial_suspend_8250’:
drivers/tty/serial/of_serial.c:262:20: warning: unused variable ‘port’ [-Wunused-variable]
  struct uart_port *port = &port8250->port;
                    ^
drivers/tty/serial/of_serial.c: In function ‘of_serial_resume_8250’:
drivers/tty/serial/of_serial.c:272:20: warning: unused variable ‘port’ [-Wunused-variable]
  struct uart_port *port = &port8250->port;
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct reference in C-comment after #endif.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The CONFIG_ prefix is reserved for Kconfig options in Make and CPP
syntax; static analysis tools rely on this convention.  This patch
enforces this behavior for SERIAL_BFIN_{HARD_}CTSRTS.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix reference on PPC_MPC52xx in C comment after #endif.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This file local CPP identifier is not referenced anywhere else, so we
can safely remove it.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Handle the changed flag of IRQ status in interruption
instead of handling it in tasklet due to the tasklet
may be scheduled more than once in one interruption.
Otherwise, the changed status may be processed more
than once which will lead to unexpected result. And
seriously, kernel will crash.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'CONFIG_' prefix is reserved for Kconfig options in Make and CPP
syntax only.  Remove this prefix from the self-defined CPP identifier to
apply to this convention and make static analysis tools happy.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ETRAX_SERIAL_PROC_ENTRY is not defined in Kconfig.  The affected #ifdef
block has not been compiled for years, and the embedded macro, PROCSTAT,
ended up as a NOOP.  Hence, remove the block and all calls to PROCSTAT.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ETRAX_RS485_{ON_PORT_G, LTC1387} are not defined in Kconfig.  The
affected #ifdef block have not been compiled for years, so remove them
entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ETRAX_EXTERN_PB6CLK_ENABLED is not defined in Kconfig.  The affected
 #ifdef block has not been compiled for years, so remove it entirely.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct reference on CONFIG_SERIAL_ALTERA_{JTAG}UART_CONSOLE in
C-comment after #endif.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig option ARCH_SH7372 has been removed by commit 59b89af1
("ARM: shmobile: sh7372: Remove Legacy C SoC code").  This patch removes
the last reference on this Kconfig option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.

Mostly generated by the coccinelle script

@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
  <+...
- tty_name(tty, buf)
+ tty_name(tty)
  ...+>

allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All users of tty_name pass the return value (the provided buffer) to
some printf-like function. We can thus avoid the strcpy and, more
importantly, later remove the buf parameter completely, eliminating
the need for some 64 byte stack buffers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All users of tty_name pass the result directly to a printf-like
function. This means we can actually let tty_name return the literal
"NULL tty" or tty->name directly, avoiding the strcpy and a lot of
medium-sized stack buffers. In preparation for that, make the return
type const char*.

While at it, we can also constify the tty parameter.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The return value from imx_setup_ufcr() is always 0 and its value is never
checked, so better to remove the return value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Previously Soft Reset (clear of SRST bit in UCR2 register)
of UART in startup is not protected by lock, which may have race
with console_write, as console_write may occur at anytime even
when UART port is shutdown.

To avoid this race, protect Soft reset of UART port with spin_lock.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 734745ca serial/amba-pl011: Activate TX IRQ passively
adds some complexity and overhead in the form of a softirq
mechanism for transmitting in the absence of interrupts.

This patch simplifies the code flow to reduce the reliance on
subtle behaviour and avoid fragility under future maintenance.

To this end, the TX softirq mechanism is removed and instead
pl011_start_tx() will now simply stuff the FIFO until full
(guaranteeing future TX IRQs), or until there are no more chars
to write (in which case we don't care whether an IRQ happens).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f2ee6dfa.

Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.

Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.

Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>