Pin data for I2C controllers 0, 3 and 5 is properly defined already.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Replace "F_(0,0)" by "F_(0, 0)".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the sel_ndfc MOD_SEL register bit is renamed to sel_ndf.

Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car E3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of Dec
22, 2017, and the Errata for Rev 1.50 of Dec 25, 2018, MOD_SEL0 register
bits 3, 4, 17, and 18 are renamed from SEL_ADG_{A,B,C} to
SEL_ADG{A,B,C}.  Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Jun 4, 2018, the CC5_OSCOUT pin is removed.  Update the pin control
drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car V3M, V3H]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

The HDMI CEC function is not supported by the R-Car Gen3 Hardware Manual
Rev 1.00. Therefore, delete the corresponding pin groups and functions,
and rename the HDMI[01]_CEC definitions to match their GPIO
functionality.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed several commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

  - The IPSR field is meant for documentation only,
  - The function name refers to the pin function, not to the IPSR
    field.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

rza1_get_bit() is just a single register read.  Hence there's no need to
synchronize it with other register writes to the same bank.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>

Add a run-time check to the PINMUX_CFG_REG_VAR() macro, to ensure the
number of provided enum IDs is correct.  This cannot be done at build
time, as the number of values depends on the variable-width fields in
the config register.

This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add build-time checks to the PINMUX_CFG_REG() and PINMUX_DATA_REG()
macros, to ensure the number of provided enum IDs is correct.

This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Currently the PINMUX_DATA_REG() macro must be followed by initialization
data, specifying all enum IDs.  Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.

Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using the GROUP()
macro.

No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs.  Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.

Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.

No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs.  Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.

Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().

No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable compile-testing of all Renesas SuperH and ARM pin control
drivers, in a similar way as was done before for clock and SoC drivers
in commits 371dd373 ("clk: renesas: Allow compile-testing of all
(sub)drivers") and 8be381a1 ("soc: renesas: Rework Kconfig and
Makefile logic").

The SuperH pin control drivers need specific include files, hence make
sure they are always found when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

When compile-testing on arm:

    arch/sh/include/cpu-sh4/cpu/sh7786.h: In function ‘sh7786_mm_sel’:
    arch/sh/include/cpu-sh4/cpu/sh7786.h:135:21: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [-Wint-conversion]
      return __raw_readl(0xFC400020) & 0x7;
			 ^~~~~~~~~~
    In file included from include/linux/io.h:25:0,
		     from arch/sh/include/cpu-sh4/cpu/sh7786.h:14,
		     from drivers/pinctrl/sh-pfc/pfc-sh7786.c:15:
    arch/arm/include/asm/io.h:113:21: note: expected ‘const volatile void *’ but argument is of type ‘unsigned int’
     #define __raw_readl __raw_readl
			 ^
    arch/arm/include/asm/io.h:114:19: note: in expansion of macro ‘__raw_readl’
     static inline u32 __raw_readl(const volatile void __iomem *addr)
		       ^~~~~~~~~~~

__raw_readl() on SuperH is a macro that casts the passed I/O address to
the correct type, while the implementations on most other architectures
expect to be passed the correct pointer type.

Add an explicit cast to fix this.

Note that this also gets rid of a sparse warning on SuperH:

    arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: warning: incorrect type in argument 1 (different base types)
    arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16:    expected void const volatile [noderef] <asn:2>*<noident>
    arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16:    got unsigned int
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

Source files using -Exxx error codes should include <linux/errno.h>.
On ARM, this header file is included indirectly; on SuperH, it is not,
leading to "error: ‘EINVAL’ undeclared" failures when enabling
compile-testing later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

Pinctrl drivers for SuperH platforms use legacy function GPIOs.
Currently this support is compiled in based on the SUPERH platform
dependency, which hinders the introduction of compile-testing support
for the affected pinctrl drivers.

Introduce a new Kconfig symbol PINCTRL_SH_FUNC_GPIO, which is
auto-selected when needed.  This symbol in turn selects
PINCTRL_SH_PFC_GPIO, to reduce the number of per-driver selects.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

Perform some basic sanity checks on all built-in pinmux tables when
DEBUG is defined, to help catching bugs early.

For now the following checks are included:
  - Check register and field widths in descriptors for config registers
    with variable-width fields,
  - Check relations between pin groups and functions:
      - All pin functions must refer to existing pin groups,
      - All pin groups must be referred to by a pin function,
      - Warn if a pin group is referred to by multiple pin functions
	(which is OK for backwards-compatibility aliases),
  - Provide suggestions for reducing table sizes: reserved fields of
    more than 3 bits can better be split in smaller subfields, as the
    storage need is proportional to the square of the width of the
    (sub)field,

Note that a dummy non-matching entry is added to the DT match table for
checking r8a7795es1_pinmux_info, as R-Car H3 ES1.0 is matched using
soc_device_match() in r8a7795_pinmux_init(), instead of by the DT match
table.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>

The TDSELCTRL register is responsible for configuring the SDHI/MMC clock
return path delay and may be adjusted by the bootloader. Retain the value
across suspend/resume to prevent hardware instability after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

CANFD is found also on the R8A774C0, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

CANFD is found also on the R8A774A1, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Adds HSCIF0 and HSCIF1 pins, groups and functions for R8A7779.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car E3, to reflect better their actual purposes, and matching other
SoCs.

Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>

The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3H, to reflect better their actual purposes, and matching other
SoCs.

Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>

The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3M, to reflect better their actual purposes, and matching other
SoCs.

Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06

When this .gitignore was added, lxdialog was an independent hostprogs-y.

Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.

um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The generic-y is redundant under the following condition:

 - arch has its own implementation

 - the same header is added to generated-y

 - the same header is added to mandatory-y

If a redundant generic-y is found, the warning like follows is displayed:

  scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h

I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This reverts commit caf6fe91.

The commit was fine but is no longer needed as of commit 3a2429e1
("kbuild: change if_changed_rule for multi-line recipe").  Let's go
back to using ";" to be consistent.

For some discussion, see:

https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.comSigned-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>