struct imx274_frmfmt is instantiated only in the imx274_formats[]
array, where imx274_formats[N].mode always equals N (via enum
imx274_mode).  So .mode carries no information, and unsurprisingly it
is never used.

mbus_code is never used because the 12 bit modes are not implemented.

The colorspace member is also never used, which is normal since the
imx274 sensor can output only one colorspace.

Let's get rid of all of them.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

imx274_s_frame_interval() already has a direct pointer to the v4l2
exposure control, so reuse it to simplify code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

interal->interval
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Document the unit to avoid having to look through the code to compute it.
Also clarify that these are min and max values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.

Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.

Detected by CoverityScan, CID#1324008 ("Logically dead code")

Fixes: ccfc97bd ("[media] smiapp: Add driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The ov7251 sensor is a 1/7.5-Inch B&W VGA (640x480) CMOS Digital Image
Sensor from Omnivision.

The driver supports the following modes:
- 640x480 30fps
- 640x480 60fps
- 640x480 90fps

Output format is 10bit B&W RAW - MEDIA_BUS_FMT_Y10_1X10.

The driver supports configuration via user controls for:
- exposure and gain;
- horizontal and vertical flip;
- test pattern.

[Sakari Ailus: Wrap a line over 80 characters, fix trivial sparse warning]
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add the document for ov7251 device tree binding.

CC: Rob Herring <robh@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The active frame size is set in the initialization arrays, but the value
itself is also available in the struct ov5640_mode_info.

Let's move these values out of the big bytes arrays, and program it with
the value of the mode that we are given.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

All the initialization arrays are changing the horizontal and vertical
totals for some value.

In order to clean up the driver, and since we're going to need that value
later on, let's introduce in the ov5640_mode_info structure the horizontal
and vertical total sizes, and move these out of the bytes array.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The current width and height parameters in the struct ov5640_mode_info are
actually the active horizontal and vertical resolutions.

Since we're going to add a few other parameters, let's pick a better, more
precise name for these values.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The SCLK and SCLK2X dividers are fixed in stone in the initialization
array. Let's make explicit what we're doing and move that away from the
huge array to the initialization code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The sensor needs to have the auto exposure stopped while changing mode.
However, when the new mode is set, the driver will force the auto exposure
on, disregarding whether the control has been changed or not.

Bypass the controls code entirely to do that, and only use the control
value cached when restoring the auto exposure mode.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add the light frequency control to be able to set the frequency
to manual (50Hz or 60Hz) or auto.

[Sakari Ailus: Rename "ctl" as "ctrl" as agreed.]
[mchehab+samsung@kernel.org: fixed two coding style warnings]
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The s_ctrl() operation can be called when the device is placed into
power down mode.  Then, applying controls to H/W should be postponed at
this time.  Instead the controls will be restored when the streaming is
started.

Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The set_fmt() subdev pad operation for this driver currently does not
only do the driver internal format selection but also do the actual
register setup.

This doesn't work if the device power control via GPIO lines is enabled.
Because the set_fmt() can be called when the device is placed into power
down mode.

First of all, this fix adds flag to keep track of whether the device starts
streaming or not.  Then, the set_fmt() postpones applying the actual
register setup at this time.  Instead the setup will be applied when the
streaming is started.

Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

I2C transfer functions return number of successful operations (on success).

Do not return the received positive return code but instead return 0 on
success. The users of write_reg function already use this logic.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Use dev_fwnode() on the device instead of getting an fwnode handle of the
device's OF node. The result is the same on OF-based systems and looks
better, too.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Implement CRC computation configuration and reporting through the DRM
debugfs-based CRC API. The CRC source can be configured to any input
plane or the pipeline output.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The DISCOM is used to compute CRCs on display frames. Integrate it in
the display pipeline at the output of the blending unit to process
output frames.

Computing CRCs on input frames is possible by positioning the DISCOM at
a different point in the pipeline. This use case isn't supported at the
moment and could be implemented by extending the API between the VSP1
and DU drivers if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The DISCOM calculates a CRC on a configurable window of the frame. It
interfaces to the VSP through the UIF glue, hence the name used in the
code.

The module supports configuration of the CRC window through the crop
rectangle on the sink pad of the corresponding entity. However, unlike
the traditional V4L2 subdevice model, the crop rectangle does not
influence the format on the source pad.

Modeling the DISCOM as a sink-only entity would allow adhering to the
V4L2 subdevice model at the expense of more complex code in the driver,
as at the hardware level the UIF is handled as a sink+source entity. As
the DISCOM is only present in R-Car Gen3 VSP-D and VSP-DL instances it
is not exposed to userspace through V4L2 but controlled through the DU
driver. We can thus change this model later if needed without fear of
affecting userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add a parameter (in the form of a structure to ease future API
extensions) to the VSP atomic flush handler to pass CRC source
configuration, and pass the CRC value to the completion callback.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The structure is used in the API that the VSP1 driver exposes to the DU
driver. Documenting it is thus important.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

To make vsp1_subdev_set_pad_format() usable by entities that support
selection rectangles, we need to reset the crop and compose rectangles
when setting the format on the sink pad. Do so and replace the custom
set_fmt implementation of the histogram code by a call to
vsp1_subdev_set_pad_format().

Resetting the crop and compose rectangles for entities that don't
support crop and compose has no adverse effect as the rectangles are
ignored anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The implementation of the set_fmt pad operation is identical in the
three modules. Move it to a generic helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management. All files in the driver are licensed under the GPLv2+ except
for the vsp1_regs.h file which is licensed under the GPLv2. This is
likely an oversight, but fixing this requires contacting the copyright
owners and is out of scope for this patch.

While at it fix the file descriptions to match file names where copy and
paste error occurred.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
as a bridge between pixel interfaces and a CSI-2 bus.

It supports operating with an internal or external D-PHY, with up to 4
lanes, or without any D-PHY. The current code only supports the latter
case.

While the virtual channel input on the pixel interface can be directly
mapped to CSI2, the datatype input is actually a selection signal (3-bits)
mapping to a table of up to 8 preconfigured datatypes/formats (programmed
at start-up)

The block supports up to 8 input datatypes.
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The clocks enabled by csi2rx_start function are intended to be disabled in
an error path but there are two issues:

1) the loop condition is always true and

2) the first clock disabled is the the one enabling of which failed.

Fix these two bugs by changing the loop condition as well as only disabling
the clocks that were actually enabled.
Reported-by: Mauro Chehab <mchehab@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The Cadence MIPI-CSI2 TX controller is a CSI2 bridge that supports up to 4
video streams and can output on up to 4 CSI-2 lanes, depending on the
hardware implementation.

It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.
Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The Cadence CSI-2 RX Controller is an hardware block meant to be used as a
bridge between a CSI-2 bus and pixel grabbers.

It supports operating with internal or external D-PHY, with up to 4 lanes,
or without any D-PHY. The current code only supports the latter case.

It also support dynamic mapping of the CSI-2 virtual channels to the
associated pixel grabbers, but that isn't allowed at the moment either.
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The Cadence MIPI-CSI2 RX controller is a CSI2RX bridge that supports up to
4 CSI-2 lanes, and can route the frames to up to 4 streams, depending on
the hardware implementation.

It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The atomisp driver has a long list of todo items and little has been done
to address these lately while more has been added. The driver is also not
functional. In other words, the driver would not be getting out of staging
in the foreseeable future. At the same time it consumes developer
resources in order to maintain the flaky code base. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

There are lots of data structs defined there but aren't used
anywhere.

Comment them out. Gets rid of those warnings:

drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1808:45: warning: 'mt9m114_entity_ops' defined but not used [-Wunused-const-variable=]
 static const struct media_entity_operations mt9m114_entity_ops = {
                                             ^~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:35:0:
drivers/staging/media/atomisp/i2c/mt9m114.h:805:34: warning: 'mt9m114_iq' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_iq[] = {
                                  ^~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:797:34: warning: 'mt9m114_antiflicker_60hz' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_antiflicker_60hz[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:789:34: warning: 'mt9m114_antiflicker_50hz' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_antiflicker_50hz[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:682:34: warning: 'mt9m114_720_480P_init' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_720_480P_init[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:533:34: warning: 'mt9m114_960P_init' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_960P_init[] = {
                                  ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:518:34: warning: 'mt9m114_wakeup_reg' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_wakeup_reg[] = {
                                  ^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:504:34: warning: 'mt9m114_streaming' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_streaming[] = {
                                  ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:497:34: warning: 'mt9m114_suspend' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_suspend[] = {
                                  ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:393:34: warning: 'mt9m114_exitstandby' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_exitstandby[] = {
                                  ^~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

It seems that, originally, the logic would allow selecting between
fine and coarse integration. However, only coarse seems to be
implemented.

Get rid of this warning:

  drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c: In function 'mt9m114_s_exposure':
  drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1003:6: warning: variable 'exposure_local' set but not used [-Wunused-but-set-variable]
    u16 exposure_local[3];
        ^~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

If something wrong gets there, return the error.

Get rid of this warning:

  drivers/staging/media/atomisp/i2c/atomisp-gc0310.c: In function 'gc0310_init':
  drivers/staging/media/atomisp/i2c/atomisp-gc0310.c:713:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
    int ret;
        ^~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘__ov2680_set_exposure’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:400:10: warning: variable ‘hts’ set but not used [-Wunused-but-set-variable]
  u16 vts,hts;
          ^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘ov2680_detect’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:1164:5: warning: variable ‘revision’ set but not used [-Wunused-but-set-variable]
  u8 revision;
     ^~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The register settings for several resolutions aren't used
currently. So, comment them out.

Fix those warnings:

In file included from drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:35:0:
drivers/staging/media/atomisp/i2c/gc2235.h:340:32: warning: 'gc2235_960_640_30fps' defined but not used [-Wunused-const-variable=]
 static struct gc2235_reg const gc2235_960_640_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/gc2235.h:287:32: warning: 'gc2235_1296_736_30fps' defined but not used [-Wunused-const-variable=]
 static struct gc2235_reg const gc2235_1296_736_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2722.c:35:0:
drivers/staging/media/atomisp/i2c/ov2722.h:999:32: warning: 'ov2722_720p_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_720p_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:787:32: warning: 'ov2722_1M3_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_1M3_30fps[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:476:32: warning: 'ov2722_VGA_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_VGA_30fps[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:367:32: warning: 'ov2722_480P_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_480P_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:257:32: warning: 'ov2722_QVGA_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_QVGA_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function '__ov2680_set_exposure':
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:35:0:
At top level:
drivers/staging/media/atomisp/i2c/ov2680.h:736:33: warning: 'ov2680_1616x1082_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1616x1082_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:649:33: warning: 'ov2680_1456x1096_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1456x1096_30fps[]= {
                                 ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:606:33: warning: 'ov2680_1296x976_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1296x976_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:563:33: warning: 'ov2680_720p_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_720p_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:520:33: warning: 'ov2680_800x600_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_800x600_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:475:33: warning: 'ov2680_720x592_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_720x592_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:433:33: warning: 'ov2680_656x496_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_656x496_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:389:33: warning: 'ov2680_QVGA_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_QVGA_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:346:33: warning: 'ov2680_CIF_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_CIF_30fps[] = {
                                 ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:301:33: warning: 'ov2680_QCIF_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_QCIF_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/ov5693/atomisp-ov5693.c:36:0:
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:988:32: warning: 'ov5693_1424x1168_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1424x1168_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:954:32: warning: 'ov5693_2592x1944_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_2592x1944_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:889:32: warning: 'ov5693_2592x1456_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_2592x1456_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:862:32: warning: 'ov5693_1940x1096' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1940x1096[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:796:32: warning: 'ov5693_1636p_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1636p_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:758:32: warning: 'ov5693_1296x736' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1296x736[] = {
                                ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:730:32: warning: 'ov5693_976x556' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_976x556[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:672:32: warning: 'ov5693_736x496' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_736x496[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:643:32: warning: 'ov5693_192x160' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_192x160[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:616:32: warning: 'ov5693_368x304' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_368x304[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:587:32: warning: 'ov5693_336x256' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_336x256[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:540:32: warning: 'ov5693_1296x976' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1296x976[] = {
                                ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:509:32: warning: 'ov5693_654x496' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_654x496[] = {
                                ^~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The code with uses the dummy var is commented out. So,
coment out its definition/initialization.

Fix this warning:

  drivers/staging/media/atomisp/i2c/atomisp-gc2235.c: In function 'gc2235_get_intg_factor':
  drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:249:26: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
    u16 reg_val, reg_val_h, dummy;
                            ^~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The identation for several tables there are broken.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

When atomisp got merged, there were so many warnings with W=1
that we simply disabled the ones that were causing troubles.

Since then, several changes got applied to atomisp, and the
number of warnings are a way smaller than it used to be.

So, let's reenable warnings there and fix the issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

There's no sense for a Kernel driver to have __KERNEL macros
on it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>