Add a self-test for the IPv6 dsfield munge that iproute2 will support.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the pedit_dsfield forwarding selftest with coverage of "pedit ex
munge ip6 dsfield set".
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
add TJA1102 support

changes v5:
- rename __of_mdiobus_register_phy() to of_mdiobus_phy_device_register()

changes v4:
- remove unused phy_id variable

changes v3:
- export part of of_mdiobus_register_phy() and reuse it in tja11xx
  driver
- coding style fixes

changes v2:
- use .match_phy_device
- add irq support
- add add delayed registration for PHY1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.

We can solve it by defining PHY1 as child of PHY0:
	tja1102_phy0: ethernet-phy@4 {
		reg = <0x4>;

		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;

		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
		reset-assert-us = <20>;
		reset-deassert-us = <2000>;

		tja1102_phy1: ethernet-phy@5 {
			reg = <0x5>;

			interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
		};
	};

The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function will be needed in tja11xx driver for secondary PHY
support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the NXP TJA11xx PHY bindings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO()
to simplify code, avoid redundant paramenter definitions
and judgements.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.

This PHY has an internal RX delay of 1.2ns and no delay for TX.

The pad skew registers allow to set the total TX delay to max 1.38ns and
the total RX delay to max of 2.58ns (configurable 1.38ns + build in
1.2ns) and a minimal delay of 0ns.

According to the RGMII v1.3 specification the delay provided by PCB traces
should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
delay by MAC or PHY. So, we configure this PHY to the best values we can
get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
1.80ns (best calculated delay)

The phy-modes can still be fine tuned/overwritten by *-skew-ps
device tree properties described in:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:

net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing
should either under RCU in fast path or the protection of rtnl_mutex.

In the case of holding RTNL, we should add the corresponding lockdep
expression to silence the following false-positive warning:

=============================
WARNING: suspicious RCU usage
5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted
-----------------------------
drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!!
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests for vrf and xfrms with a second round after adding a
qdisc. There are a few known problems documented with the test
cases that fail. The fix is non-trivial; will come back to it
when time allows.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).

It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.

The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.

So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tracepoint support for QRTR with NS as the first candidate. Later on
this can be extended to core QRTR and transport drivers.

The trace_printk() used in NS has been replaced by tracepoints.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the act_ct SW offload in flowtable, The counter of the conntrack
entry will never update. So update the nf_conn_acct conuter in act_ct
flowtable software offload.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add device-managed devm_mdiobus_register

If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.

First user of the new functionality is r8169 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.

This also adds support for tunables to set and get downshift and
energy detect auto power-down.

The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
dt-bindings: net: mdio.yaml fixes

This patch series documents some common MDIO devices properties such as
resets (and delays) and broken-turn-around. The second patch also
rephrases some descriptions to be more general towards MDIO devices and
not specific towards Ethernet PHYs.

Changes in v3:

- corrected wording of 'broken-turn-around' in ethernet-phy.yaml and
  mdio.yaml, add Andrew's R-b tag to patch #3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of descriptions assume a PHY device, but since this binding
describes a MDIO bus which can have different kinds of MDIO devices
attached to it, rephrase some descriptions to be more general in that
regard.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the properties pertaining to the broken turn around or resets
were only documented in ethernet-phy.yaml while they are applicable
across all MDIO devices and not Ethernet PHYs specifically which are a
superset.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The turn around bytes (2) are placed between the control phase of the
MDIO transaction and the data phase, correct the wording to be more
exact.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Ocelot MAC_ETYPE tc-flower key improvements

As discussed in the comments surrounding this patch:
https://patchwork.ozlabs.org/project/netdev/patch/20200417190308.32598-1-olteanv@gmail.com/

the restrictions imposed on non-MAC_ETYPE rules were harsher than they
needed to be. IP, IPv6, ARP rules can still be added concurrently with
src_mac and dst_mac rules, as long as those MAC address rules do not ask
for an offending EtherType.

For that to actually be supported, we need to parse the EtherType from
the flower classification rule first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An attempt was made in commit fe3490e6 ("net: mscc: ocelot: Hardware
ofload for tc flower filter") to avoid clashes between MAC_ETYPE rules
and IP rules. Because the protocol blacklist should have included
ETH_P_ALL too, it created some confusion, but now the situation should
be dealt with a bit better by the patch immediately previous to this one
("net: mscc: ocelot: refine the ocelot_ace_is_problematic_mac_etype
function").

So now we can remove that check. MAC_ETYPE rules with a protocol of
ETH_P_IP, ETH_P_IPV6, ETH_P_ARP and ETH_P_ALL _are_ supported, with some
restrictions regarding per-port exclusivity which are enforced now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit mentioned below was a bit too harsh, and while it restricted
the invalid key combinations which are known to not work, such as:

tc filter add dev swp0 ingress proto ip \
      flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto all \
      flower src_mac 00:11:22:33:44:55 action drop

it also restricted some which still should work, such as:

tc filter add dev swp0 ingress proto ip \
      flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto 0x22f0 \
      flower src_mac 00:11:22:33:44:55 action drop

What actually does not match "sanely" is a MAC_ETYPE rule on frames
having an EtherType of ARP, IPv4, IPv6, in addition to SNAP and OAM
frames (which the ocelot tc-flower implementation does not parse yet, so
the function might need to be revisited again in the future).

So just make the function recognize the problematic MAC_ETYPE rules by
EtherType - thus the VCAP IS2 can be forced to match even on those
packets.

This patch makes it possible for IP rules to live on a port together
with MAC_ETYPE rules that are non-all, non-arp, non-ip and non-ipv6.

Fixes: d4d0cb741d7b ("net: mscc: ocelot: deal with problematic MAC_ETYPE VCAP IS2 rules")
Reported-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the filter's protocol is ignored except for a few special
cases (IPv4 and IPv6).

The EtherType can be matched inside VCAP IS2 by using a MAC_ETYPE key.
So there are 2 cases in which EtherType matches are supported:

  - As part of a larger MAC_ETYPE rule, such as:

    tc filter add dev swp0 ingress protocol ip \
            flower skip_sw src_mac 42:be:24:9b:76:20 action drop

  - Standalone (matching on protocol only):

    tc filter add dev swp0 ingress protocol arp \
            flower skip_sw action drop

As before, if the protocol is not specified, is it implicitly "all" and
the EtherType mask in the MAC_ETYPE half key is set to zero.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yangbo Lu says:

====================
Support programmable pins for Ocelot PTP driver

The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.

This patch-set is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c driver, and to implement 4
programmable pins with only PTP_PF_PEROUT function for now.
The PTP_PF_EXTTS function will be supported in the future, and it should
be implemented separately for Felix and Ocelot, because of different
hardware interrupt implementation in them.

Changes for v2:
	- Put PTP driver under drivers/net/ethernet/mscc/.
	- Dropped MAINTAINERS patch. Kept original maintaining.
	- Initialized PTP separately in ocelot/felix platforms.
	- Supported PPS case in programmable pin.
	- Supported disabling pin function since deadlock is fixed by Richard.
	- Returned -EBUSY if not finding pin available.
Changes for v3:
	- Re-sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable PTP programmable pin.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable PTP programmable pin.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.

Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The timestamp info should be only software timestamp capabilities
if ptp clock does not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.

This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Remove vermagic header from global include folder

Changelog:
v2:
 * Changed the implementation of patch #4 to be like Masahiro wants.
I personally don't like this implementation and changing it just to move forward
this this patchset.
v1:
https://lore.kernel.org/lkml/20200415133648.1306956-1-leon@kernel.org
 * Added tags
 * Updated patch #4 with test results
 * Changed scripts/mod/modpost.c to create inclusion of vermagic.h
   from kernel folder and not from general include/linux. This is
   needed to generate *.mod.c files, while building modules.
v0:
https://lore.kernel.org/lkml/20200414155732.1236944-1-leon@kernel.org

This is followup to the failure reported by Borislav [1] and suggested
fix later on [2].

The series removes all includes of linux/vermagic.h, updates hns and
nfp to use same kernel versioning scheme (exactly like we did for
other drivers in previous cycle) and removes vermagic.h from global
include folder.

[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic
[2] https://lore.kernel.org/lkml/20200413080452.GA3772@zn.tnic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>