AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.

To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.

To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.

Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.

Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Eric Dumazet says:

====================
net: provide common RSS key infrastructure

RSS (Receive Side Scaling) uses a 40 bytes key to provide hash for incoming
packets to select appropriate incoming queue on NIC.

Hash algo (Toeplitz) is also well known and documented by Microsoft
(search for "Verifying the RSS Hash Calculation")

Problem is that some drivers use a well known key.
It makes very easy for attackers to target one particular RX queue,
knowing that number of RX queues is a power of two, or at least some
small number.

Other drivers use a random value per port, making difficult
tuning on bonding setups.

Lets add a common infrastructure, so that host gets an unique
RSS key, and drivers do not have to worry about this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.

Also provide ethtool -x support to fetch RSS key
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Rename rss_hkey local variable to rss_key to have consistent name among
drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lendacky, Thomas <Thomas.Lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.

Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.

This patch provides infrastructure to help drivers doing the right thing.

netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.

A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.

Tested:

myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Add temperature reading and registers dump to mv88e6171

These patches centralize the temperature sensor reading code, and then
make use of it with the mv88e6171 which has a compatible
sensor. Additionally, support is added for reading the mv88e6171 via
ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6171 driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

kcalloc manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

kmalloc_array manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to limit the amount of possible links to a
neighboring node to 2. If we have more then two bearers we can also
establish more links.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Reviewed-By: Jon Maloy <jon.maloy@ericsson.com>
cc: Ying Xue <ying.xue@windriver.com>
cc: Erik Hugne <erik.hugne@ericsson.com>
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit e5a2c899.

	Commit e5a2c899 introduced an alternative_call, arch_fast_hash2,
that selects between __jhash2 and __intel_crc4_2_hash based on the
X86_FEATURE_XMM4_2.

	Unfortunately, the alternative_call system does not appear to be
suitable for use with C functions, as register usage is not handled
properly for the called functions.  The __jhash2 function in particular
clobbers registers that are not preserved when called via
alternative_call, resulting in a panic for direct callers of
arch_fast_hash2 on older CPUs lacking sse4_2.  It is possible that
__intel_crc4_2_hash works merely by chance because it uses fewer
registers.

	This commit was suggested as the source of the problem by Jesse
Gross <jesse@nicira.com>.
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dependency on INET to fix following build error. I have also
fixed MPLS dependency.

ERROR: "ip_route_output_flow" [net/openvswitch/openvswitch.ko]
undefined!
make[1]: *** [__modpost] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/chelsio/cxgb4vf/sge.c
	drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c

sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.

ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull virtio bugfix from Michael S Tsirkin:
 "This fixes a crash in virtio console multi-channel mode that got
  introduced in -rc1"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_console: move early VQ enablement

Pull networking fixes from David Miller:

 1) sunhme driver lacks DMA mapping error checks, based upon a report by
    Meelis Roos.

 2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.

 3) DMA memory allocation sizes are wrong in systemport ethernet driver,
    fix from Florian Fainelli.

 4) Fix use after free in mac80211 defragmentation code, from Johannes
    Berg.

 5) Some networking uapi headers missing from Kbuild file, from Stephen
    Hemminger.

 6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
    and macvtap has a similar bug, from Herbert Xu.

 7) Adjust several tunneling drivers to set dev->iflink after registry,
    because registry sets that to -1 overwriting whatever we did.  From
    Steffen Klassert.

 8) Geneve forgets to set inner tunneling type, causing GSO segmentation
    to fail on some NICs.  From Jesse Gross.

 9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
    Giuseppe CAVALLARO.

10) Fix spurious timeouts with NewReno on low traffic connections, from
    Marcelo Leitner.

11) Fix descriptor updates in enic driver, from Govindarajulu
    Varadarajan.

12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
    Fix from Takashi Iwai.

13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
    Borkmann.

14) psock_fanout selftest accesses past the end of the mmap ring, fix
    from Shuah Khan.

15) Fix PTP timestamping for VLAN packets, from Richard Cochran.

16) netlink_unbind() calls in netlink pass wrong initial argument, from
    Hiroaki SHIMODA.

17) vxlan socket reuse accidently reuses a socket when the address
    family is different, so we have to explicitly check this, from
    Marcelo Lietner.

18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
    and other architectures, from Guenter Roeck.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  vxlan: Do not reuse sockets for a different address family
  smsc911x: power-up phydev before doing a software reset.
  lib: rhashtable - Remove weird non-ASCII characters from comments
  net/smsc911x: Fix delays in the PHY enable/disable routines
  net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
  netlink: Properly unbind in error conditions.
  net: ptp: fix time stamp matching logic for VLAN packets.
  cxgb4 : dcb open-lldp interop fixes
  selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
  net: bcmgenet: apply MII configuration in bcmgenet_open()
  net: bcmgenet: connect and disconnect from the PHY state machine
  net: qualcomm: Fix dependency
  ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
  net: phy: Correctly handle MII ioctl which changes autonegotiation.
  ipv6: fix IPV6_PKTINFO with v4 mapped
  net: sctp: fix memory leak in auth key management
  net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
  net: ppp: Don't call bpf_prog_create() in ppp_lock
  net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
  cxgb4 : Fix bug in DCB app deletion
  ...

Merge misc fixes from Andrew Morton:
 "15 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  MAINTAINERS: add IIO include files
  kernel/panic.c: update comments for print_tainted
  mem-hotplug: reset node present pages when hot-adding a new pgdat
  mem-hotplug: reset node managed pages when hot-adding a new pgdat
  mm/debug-pagealloc: correct freepage accounting and order resetting
  fanotify: fix notification of groups with inode & mount marks
  mm, compaction: prevent infinite loop in compact_zone
  mm: alloc_contig_range: demote pages busy message from warn to info
  mm/slab: fix unalignment problem on Malta with EVA due to slab merge
  mm/page_alloc: restrict max order of merging on isolated pageblock
  mm/page_alloc: move freepage counting logic to __free_one_page()
  mm/page_alloc: add freepage on isolate pageblock to correct buddy list
  mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype
  mm/compaction: skip the range until proper target pageblock is met
  zram: avoid kunmap_atomic() of a NULL pointer

Pull Ceph fixes from Sage Weil:
 "There is an overflow bug fix for cephfs from Zheng, a fix for handling
  large authentication ticket buffers in libceph from Ilya, and a few
  fixes for the request handling code from Ilya that affect RBD volumes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: change from BUG to WARN for __remove_osd() asserts
  libceph: clear r_req_lru_item in __unregister_linger_request()
  libceph: unlink from o_linger_requests when clearing r_osd
  libceph: do not crash on large auth tickets
  ceph: fix flush tid comparision

Pull HID fixes from Jiri Kosina:

 - fix for an oops in HID core upon repeated subdriver insertion/removal
   under certain circumstances, by Benjamin Tissoires

 - quirk for another Elan Touchscreen device, by Adel Gadllah

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: core: cleanup .claimed field on disconnect
  HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103