Timur Tabi says:

====================
net: qcom/emac:

Although not related, these patches affect the same files, so they should
be applied in order.

The first patch cleans up logging of when the the phy driver is attached.

The second patch always configures the SGMII to use autonegotiation mode.

The third patch removes a redundant call to emac_mac_start().

The fourth patch removes some extraneous non-functioning WOL code.

The fifth patch adds an error handler for the SGMII block.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SGMII (internal PHY) can report decode errors via an interrupt.  It
can also report autonegotiation status changes, but we don't need to track
those.  The SGMII can recover automatically from most decode errors, so
we only reset the interface if we get multiple consecutive errors.

It's possible for bogus decode errors to be reported while the link is
being brought up.  The interrupt is registered when the interface is
opened, and it's enabled after the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The EMAC driver does not support wake-on-lan, but there is still
code left-over that partially enables it.  Remove that code and a few
macros that support it.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

emac_mac_start() uses information from the external PHY to program
the MAC, so it makes no sense to call it before the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY driver is attached only when the driver calls
phy_connect_direct().  Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up.  This is the correct time
to display information about the attached driver.

Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

do_execute_actions() implements a worthwhile optimization: in case
an output action is the last action in an action list, skb_clone()
can be avoided by outputing the current skb. However, the
implementation is more complicated than necessary.  This patch
simplify this logic.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: preparatory patches for multi-chip

In order to introduce support for multi-chip configuration, we need to
do a few enhancements. This patchset makes the number of ports in a
switch dynamic (instead of capping to DSA_MAX_PORTS), stores the switch
and index of a port in the dsa_port structure, uses it in the slave
private structure, and exposes the bridge device a port belongs to.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.

Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.

Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the bridge_dev pointer from dsa_slave_priv to dsa_port so that DSA
drivers can access this information and remove the need to cache it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Store a pointer to the dsa_port structure in the dsa_slave_priv
structure, instead of the switch/port index.

This will allow to store more information such as the bridge device,
needed in DSA drivers for multi-chip configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.

That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.

This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
ravb: Support 1Gbps on R-Car H3 ES1.1+ and R-Car M3-W

this series adds support for gigabit communication to the Renesas
EthernetAVB controller when used in conjunction with R-Car Gen3 H3
ES1.1+ and M3-W SoCs.  Gigabit is already supported with R-Car Gen 2
SoCs.

The patch from Geert was previously posted for inclusion in v4.10 and
acked by Dave for that purpose. It was, however, not accepted by the
ARM SoC maintainers.

The path from Mizuguchi-san is to address timing problems observed
with gigabit transfers. I would like it considered although my own
testing on M3-W did not show any timing problems.

Changes since v1:
* Address various feedback for "APSR" patch as noted in its changelog
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables tx and rx clock internal delay modes (TDM and RDM).

This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.

With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:

phy mode   | ASPR delay mode
-----------+----------------
rgmii-id   | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andreas Schultz says:

====================
gtp: simple gtp improvements

This is the part of the previous "simple gtp improvements" series
that Pablo indicated should go into net-next.

The rcu_lock removal is small correctness changes. Passing invalid
to user space allows for more standards compliant handling of invalid
tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

enable userspace to send error replies for invalid tunnels
Acked-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rcu read lock is hold by default in the ip input path. There
is no need to hold it twice in the socket recv decapsulate code path.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two trivial overlapping changes conflicts in MPLS and mlx5.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) GTP fixes from Andreas Schultz (missing genl module alias, clear IP
    DF on transmit).

 2) Netfilter needs to reflect the fwmark when sending resets, from Pau
    Espin Pedrol.

 3) nftable dump OOPS fix from Liping Zhang.

 4) Fix erroneous setting of VIRTIO_NET_HDR_F_DATA_VALID on transmit,
    from Rolf Neugebauer.

 5) Fix build error of ipt_CLUSTERIP when procfs is disabled, from Arnd
    Bergmann.

 6) Fix regression in handling of NETIF_F_SG in harmonize_features(),
    from Eric Dumazet.

 7) Fix RTNL deadlock wrt. lwtunnel module loading, from David Ahern.

 8) tcp_fastopen_create_child() needs to setup tp->max_window, from
    Alexey Kodanev.

 9) Missing kmemdup() failure check in ipv6 segment routing code, from
    Eric Dumazet.

10) Don't execute unix_bind() under the bindlock, otherwise we deadlock
    with splice. From WANG Cong.

11) ip6_tnl_parse_tlv_enc_lim() potentially reallocates the skb buffer,
    therefore callers must reload cached header pointers into that skb.
    Fix from Eric Dumazet.

12) Fix various bugs in legacy IRQ fallback handling in alx driver, from
    Tobias Regnery.

13) Do not allow lwtunnel drivers to be unloaded while they are
    referenced by active instances, from Robert Shearman.

14) Fix truncated PHY LED trigger names, from Geert Uytterhoeven.

15) Fix a few regressions from virtio_net XDP support, from John
    Fastabend and Jakub Kicinski.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (102 commits)
  ISDN: eicon: silence misleading array-bounds warning
  net: phy: micrel: add support for KSZ8795
  gtp: fix cross netns recv on gtp socket
  gtp: clear DF bit on GTP packet tx
  gtp: add genl family modules alias
  tcp: don't annotate mark on control socket from tcp_v6_send_response()
  ravb: unmap descriptors when freeing rings
  virtio_net: reject XDP programs using header adjustment
  virtio_net: use dev_kfree_skb for small buffer XDP receive
  r8152: check rx after napi is enabled
  r8152: re-schedule napi for tx
  r8152: avoid start_xmit to schedule napi when napi is disabled
  r8152: avoid start_xmit to call napi_schedule during autosuspend
  net: dsa: Bring back device detaching in dsa_slave_suspend()
  net: phy: leds: Fix truncated LED trigger names
  net: phy: leds: Break dependency of phy.h on phy_led_triggers.h
  net: phy: leds: Clear phy_num_led_triggers on failure to avoid crash
  net-next: ethernet: mediatek: change the compatible string
  Documentation: devicetree: change the mediatek ethernet compatible string
  bnxt_en: Fix RTNL lock usage on bnxt_get_port_module_status().
  ...

Pull xfs uodates from Darrick Wong:
 "I have some more fixes this week: better input validation, corruption
  avoidance, build fixes, memory leak fixes, and a couple from Christoph
  to avoid an ENOSPC failure.

  Summary:
   - Fix race conditions in the CoW code
   - Fix some incorrect input validation checks
   - Avoid crashing fs by running out of space when freeing inodes
   - Fix toctou race wrt whether or not an inode has an attr
   - Fix build error on arm
   - Fix page refcount corruption when readahead fails
   - Don't corrupt userspace in the bmap ioctl"

* tag 'xfs-for-linus-4.10-rc6-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: prevent quotacheck from overloading inode lru
  xfs: fix bmv_count confusion w/ shared extents
  xfs: clear _XBF_PAGES from buffers when readahead page
  xfs: extsize hints are not unlikely in xfs_bmap_btalloc
  xfs: remove racy hasattr check from attr ops
  xfs: use per-AG reservations for the finobt
  xfs: only update mount/resv fields on success in __xfs_ag_resv_init
  xfs: verify dirblocklog correctly
  xfs: fix COW writeback race

Pull btrfs updates from Chris Mason:
 "Some fixes that we've collected from the list.

  We still have one more pending to nail down a regression in lzo
  compression, but I wanted to get this batch out the door"

* 'for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: remove ->{get, set}_acl() from btrfs_dir_ro_inode_operations
  Btrfs: disable xattr operations on subvolume directories
  Btrfs: remove old tree_root case in btrfs_read_locked_inode()
  Btrfs: fix truncate down when no_holes feature is enabled
  Btrfs: Fix deadlock between direct IO and fast fsync
  btrfs: fix false enospc error when truncating heavily reflinked file

Pull block fixes from Jens Axboe:
 "A set of fixes for this series. This contains:

   - Set of fixes for the nvme target code

   - A revert of patch from this merge window, causing a regression with
     WRITE_SAME on iSCSI targets at least.

   - A fix for a use-after-free in the new O_DIRECT bdev code.

   - Two fixes for the xen-blkfront driver"

* 'for-linus' of git://git.kernel.dk/linux-block:
  Revert "sd: remove __data_len hack for WRITE SAME"
  nvme-fc: use blk_rq_nr_phys_segments
  nvmet-rdma: Fix missing dma sync to nvme data structures
  nvmet: Call fatal_error from keep-alive timout expiration
  nvmet: cancel fatal error and flush async work before free controller
  nvmet: delete controllers deletion upon subsystem release
  nvmet_fc: correct logic in disconnect queue LS handling
  block: fix use after free in __blkdev_direct_IO
  xen-blkfront: correct maximum segment accounting
  xen-blkfront: feature flags handling adjustments

Pull rdma fixes from Doug Ledford:
 "Second round of -rc fixes for 4.10.

  This -rc cycle has been slow for the rdma subsystem. I had already
  sent you the first batch before the Holiday break. After that, we kept
  only getting a few here or there. Up until this week, when I got a
  drop of 13 to one driver (qedr). So, here's the -rc patches I have. I
  currently have none held in reserve, so unless something new comes in,
  this is it until the next merge window opens.

  Summary:

   - series of iw_cxgb4 fixes to make it work with the drain cq API

   - one or two patches each to: srp, iser, cxgb3, vmw_pvrdma, umem,
     rxe, and ipoib

   - one big series (13 patches) for the new qedr driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
  RDMA/cma: Fix unknown symbol when CONFIG_IPV6 is not enabled
  IB/rxe: Prevent from completer to operate on non valid QP
  IB/rxe: Fix rxe dev insertion to rxe_dev_list
  IB/umem: Release pid in error and ODP flow
  RDMA/qedr: Dispatch port active event from qedr_add
  RDMA/qedr: Fix and simplify memory leak in PD alloc
  RDMA/qedr: Fix RDMA CM loopback
  RDMA/qedr: Fix formatting
  RDMA/qedr: Mark three functions as static
  RDMA/qedr: Don't reset QP when queues aren't flushed
  RDMA/qedr: Don't spam dmesg if QP is in error state
  RDMA/qedr: Remove CQ spinlock from CM completion handlers
  RDMA/qedr: Return max inline data in QP query result
  RDMA/qedr: Return success when not changing QP state
  RDMA/qedr: Add uapi header qedr-abi.h
  RDMA/qedr: Fix MTU returned from QP query
  RDMA/core: Add the function ib_mtu_int_to_enum
  IB/vmw_pvrdma: Fix incorrect cleanup on pvrdma_pci_probe error path
  IB/vmw_pvrdma: Don't leak info from alloc_ucontext
  IB/cxgb3: fix misspelling in header guard
  ...

Pull s390 fixes from Martin Schwidefsky:
 "Another two bug fixes:

   - ptrace partial write information leak

   - a guest page hinting regression introduced with v4.6"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: Fix cmma unused transfer from pgste into pte
  s390/ptrace: Preserve previous registers for short regset write

Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb fix from Konrad Rzeszutek Wilk:
 "An ARM fix in the Xen SWIOTLB - mainly the translation of physical to
  bus addresses was done just a tad too late"

* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb-xen: update dev_addr after swapping pages

Pull VFIO fix from Alex Williamson:
 "mdev IOMMU groups are not yet compatible with the powerpc SPAPR IOMMU
  backend, detect and fail group attach (Greg Kurz)"

* tag 'vfio-v4.10-rc6' of git://github.com/awilliam/linux-vfio:
  vfio/spapr: fail tce_iommu_attach_group() when iommu_data is null

If IPV6 has not been enabled in the underlying kernel, we must avoid
calling IPV6 procedures in rdma_cm.ko.

This requires using "IS_ENABLED(CONFIG_IPV6)" in "if" statements
surrounding any code which calls external IPV6 procedures.

In the instance fixed here, procedure cma_bind_addr() called
ipv6_addr_type() -- which resulted in calling external procedure
__ipv6_addr_type().

Fixes: 6c26a771 ("RDMA/cma: fix IPv6 address resolution")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Merge branch 'stable/for-jens-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus

Konrad writes:

Please pull in your 'for-linus' branch two little fixes for Xen
block front:

One fix is for handling the XEN_PAGE_SIZE != PAGE_SIZE (4KB vs 64KB
on ARM for example) mishandling while the other is fixing
the accounting for the configuration changes.

Pull media fixes from Mauro Carvalho Chehab:

 - fix a regression on tvp5150 causing failures at input selection and
   image glitches

 - CEC was moved out of staging for v4.10. Fix some bugs on it while not
   too late

 - fix a regression on pctv452e caused by VM stack changes

 - fix suspend issued with smiapp

 - fix a regression on cobalt driver

 - fix some warnings and Kconfig issues with some random configs.

* tag 'media/v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] s5k4ecgx: select CRC32 helper
  [media] dvb: avoid warning in dvb_net
  [media] v4l: tvp5150: Don't override output pinmuxing at stream on/off time
  [media] v4l: tvp5150: Fix comment regarding output pin muxing
  [media] v4l: tvp5150: Reset device at probe time, not in get/set format handlers
  [media] pctv452e: move buffer to heap, no mutex
  [media] media/cobalt: use pci_irq_allocate_vectors
  [media] cec: fix race between configuring and unconfiguring
  [media] cec: move cec_report_phys_addr into cec_config_thread_func
  [media] cec: replace cec_report_features by cec_fill_msg_report_features
  [media] cec: update log_addr[] before finishing configuration
  [media] cec: CEC_MSG_GIVE_FEATURES should abort for CEC version < 2
  [media] cec: when canceling a message, don't overwrite old status info
  [media] cec: fix report_current_latency
  [media] smiapp: Make suspend and resume functions __maybe_unused
  [media] smiapp: Implement power-on and power-off sequences without runtime PM

Pull MMC fix from Ulf Hansson:
 "MMC host: fix runtime PM resume path in dw_mmc"

* tag 'mmc-v4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: dw_mmc: force setup bus if active slots exist

Pull thermal management fix from Zhang Rui:
 "A single revert from a recently introduced problem.

  Specifics:

  Commit 7611fb68 ("thermal: thermal_hwmon: Convert to
  hwmon_device_register_with_info()"), which was introduced in 4.10-rc5,
  uses new hwmon API. But this breaks some soc thermal driver because
  the new hwmon API has a strict rule for the hwmon device name. Revert
  the offending commit as a quick solution for 4.10"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Revert "thermal: thermal_hwmon: Convert to hwmon_device_register_with_info()"