Reserve enough room for USB skb, so we don not need to check
the room every time we send frame.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Run mt76x0_register_device routine in mt76x0e_register_device
in order to register the device to the mac80211 layer.
Moreover init mt76_driver_ops data structure and register
interrupt line
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Disable ldpc coding for mt76x0 devices. Morover remove
mt76x02_mac_fill_txwi routine since it is used just in
mt76x02_mac_write_txwi
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing mac80211 callbacks in mt76x0e_ops data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Report via ethtool fw_ver and build_ver members of mt76x02_fw_header
data structure similarly to what is reported in the syslog
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_eeprom.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_txrx.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_mac.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_usb_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_util.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_phy.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_dev data structure as reference in mt76x02_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix typo in bank check in mt76x0_rf_csr_{wr,rr} routines.
This issue has never been hit since mt76x0_rf_csr_{wr,rr}
are actually used just by pci code

Fixes: 10de7a8b ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76_is_usb() to identify RF access method instead of
MT76_STATE_MCU_RUNNING flag and add warning since MCU has
to be initialized before we can access RF registers via MCU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

We have to use RF CSR method for PCIe.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add helpers to identify bus type.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

PCIe version don't use MCU for RF registers access. We need
to correct RF CSR method to support up to 127 RF registers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use dev_dbg to print BBP version.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.

This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")

Thanks to Joe Perches for spotting this when I submitted an earlier patch.

Fixes: 3c05bedb ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access.  This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659

Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Fourth set of iwlwifi patches intended for 4.20

* Support for a new scan type;
* Clean-up in the queue handling code;
* A few bug fixes;

Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2018-10-12

please apply one more patchset for net-next. This extends the TSO support
in qeth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Except for the new HW header id, this works just like TSO6 on L3 devices
and reuses all the existing data path support in qeth_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds TSO6 support for L3 qeth devices.
Just like for standard IPv6 traffic, TSO6 doesn't use IP offload and
thus runs over the normal qeth_xmit() path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TSO6 requires the full programming sequence, and not just a simple
START command. This implements the additional ENABLE command, and adds
some sanity checks that were missing for the START command.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for IPv6 TSO, turn the protocol version into a parameter
for the TSO control code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Fixes & small enhancements related to the promisc mode in HNS3

This patch-set presents some fixes and enhancements related to promiscuous
mode and MAC VLAN Table full condition in HNS3 Ethernet Driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resumes promisc mode and vlan filter status after
loopback test.

Fixes: 3b75c3df ("net: hns3: net: hns3: Add support for IFF_ALLMULTI flag")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already have BUILD_BUG_ON_ZERO() which I just hadn't found
before, so we should use it here instead of open-coding another
implementation thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Highlights:
 * merge net-next, so I can finish the hwsim workqueue removal
 * fix TXQ NULL pointer issue that was reported multiple times
 * minstrel cleanups from Felix
 * simplify lib80211 code by not using skcipher, note that this
   will conflict with the crypto tree (and this new code here
   should be used)
 * use new netlink policy validation in nl80211
 * fix up SAE (part of WPA3) in client-mode
 * FTM responder support in the stack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.

CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a stupid typo introduced in the refactoring.

Fixes: 0efe5523 ("fore200e: simplify fore200e_bus usage")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.

This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Another difference between IPv4 and IPv6 is the generation of RTM_DELROUTE
notifications when a device is taken down (admin down) or deleted. IPv4
does not generate a message for routes evicted by the down or delete;
IPv6 does. A NOS at scale really needs to avoid these messages and have
IPv4 and IPv6 behave similarly, relying on userspace to handle link
notifications and evict the routes.

At this point existing user behavior needs to be preserved. Since
notifications are a global action (not per app) the only way to preserve
existing behavior and allow the messages to be skipped is to add a new
sysctl (net/ipv6/route/skip_notify_on_dev_down) which can be set to
disable the notificatioons.

IPv6 route code already supports the option to skip the message (it is
used for multipath routes for example). Besides the new sysctl we need
to pass the skip_notify setting through the generic fib6_clean and
fib6_walk functions to fib6_clean_node and to set skip_notify on calls
to __ip_del_rt for the addrconf_ifdown path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two PNMI macros are never used
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
 variable 'ctx' set but not used [-Wunused-but-set-variable]
  struct cdc_ncm_ctx *ctx;

It not used any more after
commit fa83dbee ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arnd writes:
  "ARM: SoC fixes for 4.19

   Two last minute bugfixes, both for NXP platforms:

   * The Layerscape 'qbman' infrastructure suffers from probe ordering
     bugs in some configurations, a two-patch series adds a hotfix for
     this. 4.20 will have a longer set of patches to rework it.

   * The old imx53-qsb board regressed in 4.19 after the addition
     of cpufreq support, adding a set of explicit operating points
     fixes this."

* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  soc: fsl: qman_portals: defer probe after qman's probe
  soc: fsl: qbman: add APIs to retrieve the probing status
  ARM: dts: imx53-qsb: disable 1.2GHz OPP