On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.

On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.

This fixes a regression introduced in 3.0-rc1 by 08ee80cc
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

SCSI defines discard alignment as the offset to the first
optimal discard.  In the case of SD/MMC, that is always zero
which is the default.

SCSI defines discard granularity as a hint of a optimal
discard size.  That is much better expressed by the MMC
"preferred erase size" (pref_erase) field.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

For example, an eMMC with 2 boot partitions will have 3 threads.
The names change from:

   40 ?        00:00:00 mmcqd/0
   41 ?        00:00:00 mmcqd/0
   42 ?        00:00:00 mmcqd/0

to:

   40 ?        00:00:00 mmcqd/0
   41 ?        00:00:00 mmcqd/0boot0
   42 ?        00:00:00 mmcqd/0boot1
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The erase timeout calculation may depend on clock rate
which is zero if the clock is gated, so use
mmc_host_clk_rate() which allows for that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The MMC block driver and other drivers (e.g. mmc-test) will expect
the card to be switched to the User Data Area eMMC partition when
they start.  Hence the MMC block driver should ensure it is that
way when it is removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

mmc_sdio_power_restore() skips some steps that are performed in other
power-related codepaths which are necessary to fully reset the card.
Without this, runtime PM fails for SD8686 SDIO wifi on OLPC XO-1.5.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

HAVE_EFFICIENT_UNALIGNED_ACCESS is a config option, therefore it needs
the CONFIG_ before it when used by the preprocessor.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>

Don't try to allocate DMA resources if the platform didn't specify
positive DMA slave IDs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Commit b6147490 ("mmc: tmio: split core functionality, DMA and
MFD glue") broke handling of the TMIO_MMC_WRPROTECT_DISABLE flag by
the tmio-mmc driver. This patch restores the original behaviour.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Don't use the returned sg_len from dma_map_sg() as inparameter
to dma_unmap_sg(). Use the original sg_len for both dma_map_sg
and dma_unmap_sg according to the documentation in DMA-API.txt.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The OMAP HSMMC driver uses an ocr_mask to determine the list of voltages
supported by the card. It populates this mask based on the list of
voltages supported by the regulator that supplies the voltage.

Commit 64be9782 (omap4 hsmmc: Update ocr mask for MMC2 for regulator
to use) passed a fixed ocr_mask from the OMAP4 SDP board file to limit
the voltage to 2.9-3.0 Volts, and updated the driver to use this mask
if provided, instead of using the regulator's supported voltages.

However the commit is buggy - the ocr_mask is overridden by the
regulator's capabilities anyway. Fix this.

(The bug shows up when a system-wide suspend is attempted on the OMAP4
SDP/Blaze platforms. The eMMC card comes up at 3V, but drops to 1.65V
after the system resumes).
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

After commit e1866b33 "PM / Runtime: Rework runtime PM handling
during driver removal" was introduced, the driver core stopped
incrementing the runtime PM usage counter of the device during
the invocation of the ->remove() callback.

This indirectly broke SDIO's runtime PM path during driver removal,
because no one calls _put_sync() anymore after ->remove() completes.

This means that the power of runtime-PM-managed SDIO cards is kept
high after their driver is removed (even if it was powered down
beforehand).

Fix that by directly calling _put_sync() when the last usage
counter is downref'ed by the SDIO bus.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

MMC host drivers must be able to process interrupts during
mmc_remove_host().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Provide a dummy value of NO_IRQ for architectures that don't support
it (such as MIPS).  Fixes the build error for MIPS.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

In isofs_fill_super(), when an iso_primary_descriptor is found, it is
kept in pri_bh.  The error cases don't properly release it.  Fix it.
Reported-and-tested-by: 김원석 <stanley.will.kim@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Fix gen6 (SNB) missed BLT ring interrupts.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] powernow-k8: Don't try to transition if the pstate is incorrect
  [CPUFREQ] powernow-k8: Don't notify of successful transition if we failed (vid case).
  [CPUFREQ] Don't set stat->last_index to -1 if the pol->cur has incorrect value.

* anon_vma-locking:
  mm: avoid anon_vma_chain allocation under anon_vma lock
  mm: avoid repeated anon_vma lock/unlock sequences in unlink_anon_vmas()
  mm: avoid repeated anon_vma lock/unlock sequences in anon_vma_clone()

Hugh Dickins points out that lockdep (correctly) spots a potential
deadlock on the anon_vma lock, because we now do a GFP_KERNEL allocation
of anon_vma_chain while doing anon_vma_clone().  The problem is that
page reclaim will want to take the anon_vma lock of any anonymous pages
that it will try to reclaim.

So re-organize the code in anon_vma_clone() slightly: first do just a
GFP_NOWAIT allocation, which will usually work fine.  But if that fails,
let's just drop the lock and re-do the allocation, now with GFP_KERNEL.

End result: not only do we avoid the locking problem, this also ends up
getting better concurrency in case the allocation does need to block.
Tim Chen reports that with all these anon_vma locking tweaks, we're now
almost back up to the spinlock performance.
Reported-and-tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This matches the anon_vma_clone() case, and uses the same lock helper
functions.  Because of the need to potentially release the anon_vma's,
it's a bit more complex, though.

We traverse the 'vma->anon_vma_chain' in two phases: the first loop gets
the anon_vma lock (with the helper function that only takes the lock
once for the whole loop), and removes any entries that don't need any
more processing.

The second phase just traverses the remaining list entries (without
holding the anon_vma lock), and does any actual freeing of the
anon_vma's that is required.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In anon_vma_clone() we traverse the vma->anon_vma_chain of the source
vma, locking the anon_vma for each entry.

But they are all going to have the same root entry, which means that
we're locking and unlocking the same lock over and over again.  Which is
expensive in locked operations, but can get _really_ expensive when that
root entry sees any kind of lock contention.

In fact, Tim Chen reports a big performance regression due to this: when
we switched to use a mutex instead of a spinlock, the contention case
gets much worse.

So to alleviate this all, this commit creates a small helper function
(lock_anon_vma_root()) that can be used to take the lock just once
rather than taking and releasing it over and over again.

We still have the same "take the lock and release" it behavior in the
exit path (in unlink_anon_vmas()), but that one is a bit harder to fix
since we're actually freeing the anon_vma entries as we go, and that
will touch the lock too.
Reported-and-tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The failure appeared in dmesg as:

[drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt
ring idle [waiting on 35064155, at 35064155], missed IRQ?

This works around that problem on by making the blitter command
streamer write interrupt state to the Hardware Status Page when a
MI_USER_INTERRUPT command is decoded, which appears to force the seqno
out to memory before the interrupt happens.

v1->v2: Moved to prior interrupt handler installation and RMW flags as
per feedback.
v2->v3: Removed RMW of flags (by anholt)

Cc: stable@kernel.org
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> [v1]
Tested-by: Eric Anholt <eric@anholt.net> [v1,v3]
	   (incidence of the bug with a testcase went from avg 2/1000 to
	   0/12651 in the latest test run (plus more for v1))
Tested-by: Kenneth Graunke <kenneth@whitecape.org> [v1]
Tested-by: Robert Hooker <robert.hooker@canonical.com> [v1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33394Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix no NID error with VIA codecs
  ALSA: isight: adjust for new queueing API
  ALSA: 6fire - Fix signedness bug
  ALSA: lola - Fix section mismatch
  ALSA: hda - Fix missing static inline to beep dummy function
  ALSA: 6fire: Fix double-free bug in usb6fire_fw_ezusb_upload()
  ALSA: hda - Fix beep_device compilation warnings
  ALSA: hda - Fix wrong auto-mute type for Acer Aspire-one
  ALSA: emu10k1: Add details for E-mu 0404 PCIe version
  ALSA: hdspm - Add firmware revision ID for RME MADI PCI version
  ALSA: hdspm - Fix jumping external wordclock frequency in AutoSync mode
  ALSA: hdspm - Fix locking in snd_hdspm_midi_input_read

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: make log devices with write back caches work
  xfs: fix ->mknod() return value on xfs_get_acl() failure

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  Revert "HID: magicmouse: ignore 'ivalid report id' while switching modes"
  HID: hid-multitouch: fix broken eGalax
  HID: MAINTAINERS: Update USB HID/HIDBP DRIVERS pattern
  HID: hid-multitouch: add support for Chunghwa multi-touch panel
  HID: hiddev: fix use after free in hiddev_release
  HID: add quirk for HyperPen 10000U
  HID: hiddev: fix potential use-after-free

* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
  gpio: add GPIOF_ values regardless on kconfig settings
  gpio: include linux/gpio.h where needed
  gpio/omap4: Fix missing interrupts during device wakeup due to IOPAD.

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi/bfin_spi: fix handling of default bits per word setting

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP1: PM: register notifiers with generic clock ops even when !PM_RUNTIME
  omap: pandora: fix NAND support
  OMAP: PM: omap_device: fix device power domain callbacks
  OMAP: PM debug: fix section mismatch warnings

____call_usermodehelper() now erases any credentials set by the
subprocess_inf::init() function.  The problem is that commit
17f60a7d ("capabilites: allow the application of capability limits
to usermode helpers") creates and commits new credentials with
prepare_kernel_cred() after the call to the init() function.  This wipes
all keyrings after umh_keys_init() is called.

The best way to deal with this is to put the init() call just prior to
the commit_creds() call, and pass the cred pointer to init().  That
means that umh_keys_init() and suchlike can modify the credentials
_before_ they are published and potentially in use by the rest of the
system.

This prevents request_key() from working as it is prevented from passing
the session keyring it set up with the authorisation token to
/sbin/request-key, and so the latter can't assume the authority to
instantiate the key.  This causes the in-kernel DNS resolver to fail
with ENOKEY unconditionally.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default bits per word setting should be 8 bits, but since most of our
devices have been explicitly setting this up, we didn't notice when the
default stopped working.

At the moment, any default transfers without an explicit bit size setting
error out with:
bfin-spi bfin-spi.0: transfer: unsupported bits_per_word

So in the transfer logic, have a bits_per_word setting of 0 fall into the
8 bit transfer logic.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The via driver spews warnigs like
	hda-codec: no NID for mapping control Independent HP:0:0
with some codecs because snd_hda_add_nid() is called with nid=0.
This patch fixes it by skipping the call when no corresponding widget
is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since commit 13882a82 (optimize iso queueing by setting
wake only after the last packet), drivers are required to call
fw_iso_context_queue_flush() after queueing a batch of packets.
The missing call would have an effect only if the controller
queue underruns, but then the DMA would stop completely.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: use helper functions for fence read/write
  drm/radeon/kms: set DP link config properly for DP bridges
  drm/radeon/kms/atom: AdjustPixelClock fixes for DP bridges
  drm/radeon/kms: fix handling of DP to LVDS bridges
  drm/radeon/kms: issue blank/unblank commands for ext encoders
  drm/radeon/kms: fix support for DDC on dp bridges
  drm/radeon/kms: add support for load detection on dp bridges
  drm/radeon/kms: add missing external encoder action
  drm/radeon/kms: rework atombios_get_encoder_mode()
  drm/radeon/kms: fix num crtcs for Cedar and Caicos
  Revert "drm/i915: Enable GMBUS for post-gen2 chipsets"
  drivers/gpu/drm: use printk_ratelimited instead of printk_ratelimit
  drm/radeon: workaround a hw bug on some radeon chipsets with all-0 EDIDs.
  drm: make debug levels match in edid failure code.
  drm/radeon/kms: clear wb memory by default
  drm/radeon/kms: be more pedantic about the g5 quirk (v2)
  drm/radeon/kms: signed fix for evergreen thermal
  drm: populate irq_by_busid-member for pci

The existing code assumed scratch registers in a number
of places while in most cases we are be using writeback
and events rather than scratch registers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

DP clock and lanes were not set properly for DP bridges.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

They need to be treated like eDP rather than DP.

May fix:
https://bugzilla.kernel.org/show_bug.cgi?id=34822Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Required for DPMS on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>