Most SoC GPIO implementations, including the Aspeed one, have
synchronizers on the GPIO inputs. This means that the value
read from a GPIO is a couple of clocks old, from whatever clock
source feeds those synchronizers.

In practice, this means that in no-delay mode, we are using a
value that can potentially be a bit too old and too close to
the clock edge establishing the data on the other side of the link.

The voltage converters we use on some systems make this worse
and sensitive to things like voltage fluctuations etc... This is,
we believe, the cause of occasional CRC errors encountered during
heavy activity on the LPC bus.

This is fixed by introducing a dummy GPIO read before the actual
data read. It slows down SBEFIFO by about 15% (less than any delay
primitive) and the end result is so far solid.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>

FSI_GPIO_DPOLL_CLOCKS is the number of clocks before sending
a DPOLL command after receiving a BUSY status. It should be
at least tSendDelay (16 clocks).

According to comments in the code, it needs to also be at least
21 clocks due to HW issues.

It's currently 100 clocks which impacts performances negatively
in some cases. Reduces it in half to 50 clocks which seems to
still be solid.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>

FSI_GPIO_PRIME_SLAVE_CLOCKS is the number of clocks if the
"idle" phase between the end of a response and the beginning
of the next one. It corresponds to tSendDelay in the FSI
specification.

The default value in the slave is 16 clocks. 100 is way overkill
and significantly reduces the driver performance.

This changes it to 20 (which gives the HW a bit of margin still
just in case).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>

This adds support for an optional device-tree property that
makes the driver skip all the delays around clocking the
GPIOs and set it in the device-tree of common POWER9 based
OpenPower platforms.

This useful on chips like the AST2500 where the GPIO block is
running at a fairly low clock frequency (25Mhz typically). In
this case, the delays are unnecessary and due to the low
precision of the timers, actually quite harmful in terms of
performance.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>

We currently sample the input data right after we toggle the
clock low, then high. The slave establishes the data on the
rising edge, so this is not ideal. We should sample it on
the low phase instead.

This currently works because we have an extra delay, but subsequent
patches will remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>

Reduce time spent with interrupts disabled by limiting the critical
sections to bitbanging FSI symbols. We only need to ensure exclusive use
of the bus for an entire transfer, not that the transfer be performed in
atomic context.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>

An observation from trace output of the existing FSI tracepoints was
that the remote device was sometimes reporting as busy. Add a new
tracepoint reporting the busy count in order to get a better grip on how
often this is the case.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Joel Stanley <joel@jms.id.au>

Pull ARM SoC late updates from Olof Johansson:
 "This is a branch with a few merge requests that either came in late,
  or took a while longer for us to review and merge than usual and thus
  cut it a bit close to the merge window. We stage them in a separate
  branch and if things look good, we still send them up -- and that's
  the case here.

  This is mostly DT additions for Renesas platforms, adding IP block
  descriptions for existing and new SoCs.

  There are also some driver updates for Qualcomm platforms for SMEM/QMI
  and GENI, which is their generalized serial protocol interface"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
  soc: qcom: smem: introduce qcom_smem_virt_to_phys()
  soc: qcom: qmi: fix a buffer sizing bug
  MAINTAINERS: Update pattern for qcom_scm
  soc: Unconditionally include qcom Makefile
  soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
  soc: qcom: smem: fix qcom_smem_set_global_partition()
  soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
  soc: qcom: smem: byte swap values properly
  soc: qcom: smem: return proper type for cached entry functions
  soc: qcom: smem: fix first cache entry calculation
  soc: qcom: cmd-db: Make endian-agnostic
  drivers: qcom: add command DB driver
  arm64: dts: renesas: salvator-common: Add ADV7482 support
  ARM: dts: r8a7740: Add CEU1
  ARM: dts: r8a7740: Add CEU0
  arm64: dts: renesas: salvator-common: enable VIN
  arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7795-es1: add CSI-2 node
  ...

Pull ARM SoC driver updates from Olof Johansson:
 "This contains platform-related driver updates for ARM and ARM64.

  Highlights:

   - ARM SCMI (System Control & Management Interface) driver cleanups

   - Hisilicon support for LPC bus w/ ACPI

   - Reset driver updates for several platforms: Uniphier,

   - Rockchip power domain bindings and hardware descriptions for
     several SoCs.

   - Tegra memory controller reset improvements"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
  ARM: tegra: fix compile-testing PCI host driver
  soc: rockchip: power-domain: add power domain support for px30
  dt-bindings: power: add binding for px30 power domains
  dt-bindings: power: add PX30 SoCs header for power-domain
  soc: rockchip: power-domain: add power domain support for rk3228
  dt-bindings: power: add binding for rk3228 power domains
  dt-bindings: power: add RK3228 SoCs header for power-domain
  soc: rockchip: power-domain: add power domain support for rk3128
  dt-bindings: power: add binding for rk3128 power domains
  dt-bindings: power: add RK3128 SoCs header for power-domain
  soc: rockchip: power-domain: add power domain support for rk3036
  dt-bindings: power: add binding for rk3036 power domains
  dt-bindings: power: add RK3036 SoCs header for power-domain
  dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
  memory: tegra: Remove Tegra114 SATA and AFI reset definitions
  memory: tegra: Register SMMU after MC driver became ready
  soc: mediatek: remove unneeded semicolon
  soc: mediatek: add a fixed wait for SRAM stable
  soc: mediatek: introduce a CAPS flag for scp_domain_data
  soc: mediatek: reuse regmap_read_poll_timeout helpers
  ...

Pull ARM SoC device tree updates from Olof Johansson:
 "As always, a large number of DT updates. Too many to enumerate them
  all, but at a glance:

  New SoCs introduced in this release:

   - Amlogic:
      + Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
        set top boxes and other products.

   - Mediatek:
      + MT7623A, which is a flavor of the MT7623 family with other
        on-chip ethernet options.

   - Qualcomm:
      + SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
        (Cortex-A75/A55 derivative) SoC that's one of the current
        high-end mobile SoCs.

        It's great to see mainline support for it. So far, you can't do
        much with it, since a lot of peripherals are not yet in the DTs
        but driver support for USB, GPU and other pieces are starting to
        trickle in. This might end up being a well-supported SoC
        upstream if the momentum keeps up.

   - Renesas:
      + R8A77990, a.k.a R-Car E3, a new automotive
        entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
        enabled, we are eagerly awaiting more. So far, basic drivers
        such as serial, gpios, PMU and ethernet are enabled.
      + R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
        GPU. Same here, basic set of drivers such as serial, gpios and
        ethernet enabled, and SMP support is also forthcoming.

   - STMicroelectronics:
      + STM32F469, very similar tih STM32F429 but with display support

  Enhancements to SoCs/platforms (DTS contents, some driver portions
  might not be in yet):
   - Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
   - Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
   - Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
   - Marvell Berlin2CD: SMP support, thermal sensors
   - Mediatek MT7623: Highspeed DMA, audio support
   - Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
   - Renesas: Watchdog and PMU support across many platforms
   - Rockchip RK3399: USB3 OTG support
   - Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
   - STMicro STM32: Lots of peripherals added to STM32MP175C
   - Uniphier: Ethernet support

  New boards:
   - Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
   - Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
   - Allwinner A33: Nintendo NES/SuperNES Classic Edition
   - Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
   - Berlin2CD: Valve Steam Link
   - Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
   - Broadcom: Raspberry Pi 3 B+
   - Mediatek MT7623N and MT7623A: reference boards
   - Meson 8M2: Tronsmart MXIII Plus
   - NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
   - Qualcomm MSM8974: Sony Xperia Z1 Compact support
   - Qualcomm SDM845: MTP development board
   - Renesas: Ebisu R8A77990 board
   - Renesas RZ/G1C: iwg23s: iWave G235-SDB
   - TI am335x: Pocketbeagle support"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
  ARM: dts: aspeed: Fix hwrng register address
  arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
  arm64: dts: sprd: Add GPIO and GPIO keys device nodes
  arm64: dts: sprd: fix typo in 'remote-endpoint'
  arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
  arm64: dts: fix regulator property name for wlan pcie endpoint
  arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
  ARM: dts: pxa3xx: fix MMC clocks
  ARM: pxa: dts: add pin definitions for extended GPIOs
  ARM: pxa: dts: add gpio-ranges to gpio controller
  ARM: dts: ipq8074: Enable few peripherals for hk01 board
  ARM: dts: ipq8074: Add pcie nodes
  ARM: dts: ipq8074: Add peripheral nodes
  ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
  ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
  ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
  ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
  ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
  ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
  ARM: dts: ipq4019: Change the max opp frequency
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Here are the main updates for SoC support (besides DT additions) for
  ARM 32- and 64-bit platforms. The branch also contains defconfig
  updates to turn on drivers and options as needed on the various
  platforms.

  The largest parts of the delta are from cleanups moving platform data
  and board file setup of TI platforms to ti-sysc bus drivers. There are
  also some sweeping changes of eeprom and nand setup on Davinci, i.MX
  and other platforms.

  Samsung is removing support for Exynos5440, which was an oddball SoC
  that hasn't been seen much use in designs.

  Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).

  Linus Walleij is also removing support for ux500 (Sony Ericsson)
  U8540/9540 SoCs that never made it to significant mass production and
  products"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
  MAINTAINERS: add NXP linux team maillist as i.MX reviewer
  ARM: stm32: Don't select DMA unconditionally on STM32MP157C
  arm64: defconfig: Enable PCIe on msm8996 and db820c
  ARM: pxa3xx: enable external wakeup pins
  ARM: pxa: stargate2: use device properties for at24 eeprom
  arm64: defconfig: Enable HISILICON_LPC
  arm64: defconfig: enable drivers for Poplar support
  arm64: defconfig: Enable UFS on msm8996
  ARM: berlin: switch to SPDX license identifier
  arm: berlin: remove non-necessary flush_cache_all()
  ARM: berlin: extend BG2CD Kconfig entry
  OMAP: CLK: CLKSRC: Add suspend resume hooks
  ARM: AM43XX: Add functions to save/restore am43xx control registers
  ASoC: ams_delta: use GPIO lookup table
  ARM: OMAP1: ams-delta: add GPIO lookup tables
  bus: ti-sysc: Fix optional clocks array access
  ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
  ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
  ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
  ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
  ...

Merging in defconfig updates. It's useful to keep them separate during
development but little point in merging them upstream on their own.

* next/defconfig: (40 commits)
  arm64: defconfig: Enable PCIe on msm8996 and db820c
  arm64: defconfig: Enable HISILICON_LPC
  arm64: defconfig: enable drivers for Poplar support
  arm64: defconfig: Enable UFS on msm8996
  arm64: defconfig: enable the Armada thermal driver
  ARM: multi_v7_defconfig: Enable RENESAS_WDT
  ARM: shmobile: defconfig: Enable RENESAS_WDT_GEN
  arm64: defconfig: enable R8A77990 SoC
  ARM: multi_v7_defconfig: Add STM32F7 I2C & STM32 USBPHYC support
  arm64: defconfig: Increase CMA size for VC4
  arm64: defconfig: enable rockchip efuse
  ARM: imx_v6_v7_defconfig: Select CONFIG_GPIO_MAX732X by default
  ARM: imx_v6_v7_defconfig: enable imx6sll by default
  arm64: defconfig: Enable CONFIG_SND_AUDIO_GRAPH_CARD
  arm64: defconfig: makes SND_SIMPLE_CARD to module
  ARM: multi_v7_defconfig: enable the Meson PWM controller
  arm: multi_v7_defconfig: enable the Amlogic Meson I2C driver
  arm64: defconfig: enable CONFIG_SPI_ARMADA_3700
  arm64: defconfig: Enable CONFIG_PINCTRL_MT7622 by default
  arm64: defconfig: Enable bluetooth USB support
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull watchdog updates from Wim Van Sebroeck:
 "Core:
   - simplify getting .drvdata

  renesas_wdt:
   - add support for the R8A77965 WDT and R-Car Gen2
   - remove R-Car M2-W ES2.x from blacklist

  sp805:
   - add restart handler

  hpwdt:
   - claim NMIs generated by iLO5

  mena21_wdt:
   - drop unnecessary mutex lock

  da9062 & da9063:
   - fixes and general cleanups"

* tag 'linux-watchdog-4.18-rc1' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9063: remove duplicated timeout_to_sel calls
  watchdog: da9063: rename helper function to avoid misunderstandings
  watchdog: da9062: remove unused code
  watchdog: da9063: Fix timeout handling during probe
  watchdog: da9063: Fix updating timeout value
  watchdog: da9063: Fix setting/changing timeout
  dt-bindings: watchdog: renesas-wdt: Add R-Car Gen2 support
  watchdog: mena21_wdt: Drop unnecessary mutex lock
  watchdog: renesas-wdt: Add support for the R8A77965 WDT
  watchdog: hpwdt: Claim NMIs generated by iLO5
  watchdog: sp805: add restart handler
  watchdog: renesas-wdt: Remove R-Car M2-W ES2.x from blacklist
  watchdog: simplify getting .drvdata

This reverts commit b468620f.

It turns out that this broke drm on AMD platforms. Quoting Gabriel C:
 "I can confirm reverting b468620f fixes
  that issue for me.

  The GPU is working fine with SME enabled.

  Now with working GPU :) I can also confirm performance is back to
  normal without doing any other workarounds"

Christan König analyzed it partially:
 "As far as I analyzed it we now get an -ENOMEM from dma_alloc_attrs()
  in drivers/gpu/drm/ttm/ttm_page_alloc_dma.c when IOMMU is enabled"

and Christoph Hellwig responded:
 "I think the prime issue is that dma_direct_alloc respects the dma
  mask. Which we don't need if actually using the iommu. This would be
  mostly harmless exept for the the SEV bit high in the address that
  makes the checks fail.

  For now I'd say revert this commit for 4.17/4.18-rc and I'll look into
  addressing these issues properly"
Reported-and-bisected-by: Gabriel C <nix.or.die@gmail.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org		# v4.17
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull rpmsg updates from Bjorn Andersson:
 "This migrates rpmsg to use SPDX license headers and fixes a
  use-after-free in SMD"

* tag 'rpmsg-v4.18' of git://github.com/andersson/remoteproc:
  rpmsg: smd: do not use mananged resources for endpoints and channels
  rpmsg: char: Switch to SPDX license identifier
  rpmsg: glink: Switch to SPDX license identifier
  rpmsg: smd: Switch to SPDX license identifier
  rpmsg: virtio_rpmsg_bus: Switch to SPDX license identifier
  rpmsg: Switch to SPDX license identifier
  rpmsg: qcom_smd: Access APCS through mailbox framework
  rpmsg: Add driver_override device attribute for rpmsg_device

Pull remoteproc updates from Bjorn Andersson:
 "This brings a few minor fixes to the Davinci driver, drops a orphan
  include file from the StE cleanup done ealier and introduces support
  for booting the modem on Qualcomm's SDM845 platform"

* tag 'rproc-v4.18' of git://github.com/andersson/remoteproc:
  remoteproc: q6v5: Allow defining GLINK edge for mss remoteproc
  remoteproc: q6v5: Add support for mss remoteproc on SDM845
  remoteproc: q6v5: Introduce reset assert/deassert helper functions
  dt-bindings: remoteproc: Add Q6v5 Modem PIL binding for SDM845
  remoteproc: q6v5: Move proxy unvote to handover irq handler
  remoteproc: q6v5: Return irq from q6v5_request_irq()
  remoteproc/ste: remove abandoned include file
  remoteproc/davinci: use octal permissions for module_param()
  remoteproc/davinci: prepare and unprepare the clock where needed
  remoteproc/davinci: add the missing retval check for clk_enable()
  remoteproc: Remove depends on HAS_DMA in case of platform dependency
  remoteproc: Prevent incorrect rproc state on xfer mem ownership failure

Pull hwspinlock updates from Bjorn Andersson:
 "In addition to migrating the files to use SPDX license headers this
  introduces the ability for clients to operate a hwlock without the
  framework taking any additional locks"

* tag 'hwlock-v4.18' of git://github.com/andersson/remoteproc:
  hwspinlock/u8500: Switch to SPDX license identifier
  hwspinlock: sprd: Switch to SPDX license identifier
  hwspinlock/sirf: Switch to SPDX license identifier
  hwspinlock: qcom: Switch to SPDX license identifier
  hwspinlock/omap: Switch to SPDX license identifier
  hwspinlock/core: Switch to SPDX license identifier
  hwspinlock: Introduce one new mode for hwspinlock
  hwspinlock: Convert to use 'switch' statement

Al noted that the semantics of the ia64 perfmon mmap() is really wrong,
and can cause serious VM problems.  Before we look at whether it needs
to be fixed, let's see if anybody even uses it, and mark it broken.  It
may be that we can just remove the code entirely.
Reported-by: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Stephane Eranian <eranian@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull f2fs updates from Jaegeuk Kim:
 "In this round, we've mainly focused on discard, aka unmap, control
  along with fstrim for Android-specific usage model. In addition, we've
  fixed writepage flow which returned EAGAIN previously resulting in EIO
  of fsync(2) due to mapping's error state. In order to avoid old MM bug
  [1], we decided not to use __GFP_ZERO for the mapping for node and
  meta page caches. As always, we've cleaned up many places for future
  fsverity and symbol conflicts.

  Enhancements:
   - do discard/fstrim in lower priority considering fs utilization
   - split large discard commands into smaller ones for better responsiveness
   - add more sanity checks to address syzbot reports
   - add a mount option, fsync_mode=nobarrier, which can reduce # of cache flushes
   - clean up symbol namespace with modified function names
   - be strict on block allocation and IO control in corner cases

  Bug fixes:
   - don't use __GFP_ZERO for mappings
   - fix error reports in writepage to avoid fsync() failure
   - avoid selinux denial on CAP_RESOURCE on resgid/resuid
   - fix some subtle race conditions in GC/atomic writes/shutdown
   - fix overflow bugs in sanity_check_raw_super
   - fix missing bits on get_flags

  Clean-ups:
   - prepare the generic flow for future fsverity integration
   - fix some broken coding standard"

[1] https://lkml.org/lkml/2018/4/8/661

* tag 'f2fs-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (79 commits)
  f2fs: fix to clear FI_VOLATILE_FILE correctly
  f2fs: let sync node IO interrupt async one
  f2fs: don't change wbc->sync_mode
  f2fs: fix to update mtime correctly
  fs: f2fs: insert space around that ':' and ', '
  fs: f2fs: add missing blank lines after declarations
  fs: f2fs: changed variable type of offset "unsigned" to "loff_t"
  f2fs: clean up symbol namespace
  f2fs: make set_de_type() static
  f2fs: make __f2fs_write_data_pages() static
  f2fs: fix to avoid accessing cross the boundary
  f2fs: fix to let caller retry allocating block address
  disable loading f2fs module on PAGE_SIZE > 4KB
  f2fs: fix error path of move_data_page
  f2fs: don't drop dentry pages after fs shutdown
  f2fs: fix to avoid race during access gc_thread pointer
  f2fs: clean up with clear_radix_tree_dirty_tag
  f2fs: fix to don't trigger writeback during recovery
  f2fs: clear discard_wake earlier
  f2fs: let discard thread wait a little longer if dev is busy
  ...

There's no need to retain the fs/autofs4 directory for backward
compatibility.

Adding an AUTOFS4_FS fragment to the autofs Kconfig and a module alias
for autofs4 is sufficient for almost all cases. Not keeping fs/autofs4
remnants will prevent "insmod <path>/autofs4/autofs4.ko" from working
but this shouldn't be used in automation scripts rather than
modprobe(8).

There were some comments about things to look out for with the module
rename in the fs/autofs4/Kconfig that is removed by this patch, see the
commit patch if you are interested.

One potential problem with this change is that when the
fs/autofs/Kconfig fragment for AUTOFS4_FS is removed any AUTOFS4_FS
entries will be removed from the kernel config, resulting in no autofs
file system being built if there is no AUTOFS_FS entry also.

This would have also happened if the fs/autofs4 remnants had remained
and is most likely to be a problem with automated builds.

Please check your build configurations before the removal which will
occur after the next couple of kernel releases.
Acked-by: Ian Kent <raven@themaw.net>
[ With edits and commit message from Ian Kent ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull backlight updates from Lee Jones:
 "Core Frameworks
   - Provide helpers to enable/disable backlight
   - Provide standard and devres versions OF find helpers

  New Drivers:
   - Add support for the Zodiac Inflight Innovations RAVE Supervisory
     Processor

  New Functionality:
   - Allow pwm-on/pwm-off delay to be specified via DT

  Bug Fixes:
   - Fix ordering of the power {en,dis}able and PWM {en,dis}able
     signals
   - Fix Device Tree node look-up"

* tag 'backlight-next-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: as3711_bl: Fix Device Tree node leaks
  backlight: tps65217_bl: Fix Device Tree node lookup
  backlight: max8925_bl: Fix Device Tree node lookup
  backlight: as3711_bl: Fix Device Tree node lookup
  MAINTAINERS: Add dri-devel for backlight subsystem patches
  backlight: Nuke BL_CORE_DRIVER1
  staging: fbtft: Stop using BL_CORE_DRIVER1
  backlight: pandora: Stop using BL_CORE_DRIVER1
  backlight: generic-bl: Remove DRIVER1 state
  backlight: Nuke unused backlight.props.state states
  backlight: otm3225a: Add support for ORISE OTM3225A LCD SoC
  backlight: pwm_bl: Don't use GPIOF_* with gpiod_get_direction
  pwm-backlight: Add support for PWM delays proprieties.
  dt-bindings: pwm-backlight: Add PWM delay proprieties.
  pwm-backlight: Enable/disable the PWM before/after LCD enable toggle.
  dt-bindings: backlight: Add binding for RAVE SP backlight driver
  backlight: Add RAVE SP backlight driver

Pull MFD updates from Lee Jones:
 "New Device Support:
   - Add support for AXP813 ADC to AXP20x
   - Add support for PM8005, PM8998 and PMI8998

  New Functionality:
   - Add support for Battery Power Supply to AXP813
   - Add support for SYSCON to SPARD SC27XX SPI
   - Add support for RTC to ChromeOS Embedded-Controller

  Fix-ups:
   - Remove unused code; exynos{4,5}-pmu, cros_ec, cros_ec_acpi_gpe
   - Remove duplicate error messages (-ENOMEM, etc); htc-i2cpld,
        janz-cmodio, max8997, rc5t583, sm501, smsc-ece1099, abx500-core,
        si476x-i2c, ti_am335x_tscadc, tps65090, tps6586x, tps65910,
        tps80031, twl6030-irq, viperboard
   - Succinctly use ptr to struct in sizeof(); rc5t583, abx500-core,
        sm501, smsc-ece1099
   - Simplify syntax for NULL ptr checking; abx500-core, sm501
   - No not unnecessarily initialise variables; tps65910, tps65910
   - Reorganise and simplify driver data; omap-usb-tll
   - Move to SPDX license statement; tps68470
   - Probe ADCs via DT; axp20x
   - Use new GPIOD API; arizona-core
   - Constify things; axp20x
   - Reduce code-size (use MACROS, etc); axp20x, omap-usb-host
   - Add DT support/docs; motorola-cpcap
   - Remove VLAs; rave-sp
   - Use devm_* managed resources; cros_ec
   - Interrogate HW for firmware version; rave-sp
   - Provide ACPI support for ChromeOS Embedded-Controller

  Bug Fixes:
   - Reorder ordered (enum) device list; tps65218
   - Only accept valid data from the offset; rave-sp
   - Refrain from copying junk from failed SPI read; cros_ec_dev
   - Fix potential memory leaks; pcf50633-core
   - Fix clock initialisation; twl-core
   - Fix build-issue; tps65911
   - Fix off-by-one error; tps65911
   - Fix code ordering issues; intel-lpss
   - Fix COMPILE_TEST related issues; pwm-stm32
   - Fix broken MMC card detection; asic3
   - Fix clocking related issues; intel-lpss-pci"

* tag 'mfd-next-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
  mfd: cros_ec: Remove unused __remove function
  mfd: wm97xx-core: Platform data can be NULL
  mfd: cros_ec_dev: Don't advertise junk features on failure
  mfd: cros_ec: Use devm_kzalloc for private data
  mfd: intel-lpss: Fix Intel Cannon Lake LPSS I2C input clock
  mfd: asic3: Fix broken MMC card detection
  mfd: timberdale: Fix spelling mistake "Uknown" -> "Unknown"
  mfd: omap-usb-host: Use match_string() helper
  mfd: stm32-timers: Fix pwm-stm32 linker issue with COMPILE_TEST
  pwm: stm32: Initialize raw local variables
  mfd: arizona: Update DT doc to support more standard Reset binding
  dt-bindings: mfd: Add bindings for DA9063L
  mfd: intel-lpss: Correct names of RESETS register bits
  mfd: qcom-spmi-pmic: Add support for pm8005, pm8998 and pmi8998
  mfd: intel-lpss: Program REMAP register in PIO mode
  mfd: cros_ec_i2c: Moving the system sleep pm ops to late
  mfd: cros_ec_i2c: Add ACPI module device table
  mfd: cros_ec_dev: Register shutdown function for debugfs
  mfd: cros_ec_dev: Register cros-ec-rtc driver as a subdevice
  mfd: cros_ec: Don't try to grab log when suspended
  ...

Pull drm msm updates and misc fixes from Dave Airlie:
 "I looked at Rob's msm tree, he kept it small due to being late, and it
  was in -next for a while before he was ill, so I think it should be
  fine.

  Otherwise this contains a set of i915 fixes and a v3d build fix, and
  vc4 leak fix"

* tag 'drm-next-2018-06-11' of git://anongit.freedesktop.org/drm/drm: (31 commits)
  drm/i915/icl: Don't update enabled dbuf slices struct until updated in hw
  drm/i915/icl: fix icl_unmap/map_plls_to_ports
  drm/i915: Remove bogus NV12 PLANE_COLOR_CTL setup
  drm/msm: Fix NULL deref on bind/probe deferral
  drm/msm: Switch to atomic_helper_commit()
  drm/msm: Remove msm_commit/worker, use atomic helper commit
  drm/msm: Issue queued events when disabling crtc
  drm/msm: Move implicit sync handling to prepare_fb
  drm/msm: Refactor complete_commit() to look more the helpers
  drm/msm: Don't subclass drm_atomic_state anymore
  drm/msm/mdp5: Use the new private_obj state
  drm/msm/mdp5: Add global state as a private atomic object
  drm/msm: use correct aspace pointer in msm_gem_put_iova()
  drm/msm: remove unbalanced mutex unlock
  drm/msm: don't deref error pointer in the msm_fbdev_create error path
  drm/msm/dsi: use correct enum in dsi_get_cmd_fmt
  drm/msm: Fix possible null dereference on failure of get_pages()
  drm/msm: Add modifier to mdp_get_format arguments
  drm/msm: Mark the crtc->state->event consumed
  drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY
  ...

Two framebuffer device-node names were looked up during probe, but were
only used as flags to indicate the presence of two framebuffer device.

Drop the unused framebuffer name along with a likewise unused device
pointer from the driver data, and update the platform data to pass in
booleans instead of the framebuffer strings. This allows us do drop the
node references acquired during probe, which would otherwise leak.

Note that there are no other in-kernel users of the modified
platform-data fields.

Fixes: 59eb2b5e ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.

This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.

Cc: stable <stable@vger.kernel.org>     # 3.7
Fixes: eebfdc17 ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.

To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.

Cc: stable <stable@vger.kernel.org>     # 3.9
Fixes: 47ec340c ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.

To make things worse, the parent mfd node was also prematurely freed.

Cc: stable <stable@vger.kernel.org>     # 3.10
Fixes: 59eb2b5e ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This function is no longer called, so we get a harmless
warning until it is removed as well:

drivers/mfd/cros_ec_dev.c:265:13: error: '__remove' defined but not used [-Werror=unused-function]

Fixes: 3aa2177e ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is not mandatory that platform data is passed along the ac97
codec. Actually there are configuration without a battery connected to
the ADC of the codec.

This is for example the case for the PXA zylonite platform, so fix the
NULL dereferencing by adding a test.

Fixes: a5c6951c ("mfd: wm97xx-core: core support for wm97xx Codec")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull networking fixes from David Miller:

 1) Fix several bpfilter/UMH bugs, in particular make the UMH build not
    depend upon X86 specific Kconfig symbols. From Alexei Starovoitov.

 2) Fix handling of modified context pointer in bpf verifier, from
    Daniel Borkmann.

 3) Kill regression in ifdown/ifup sequences for hv_netvsc driver, from
    Dexuan Cui.

 4) When the bonding primary member name changes, we have to re-evaluate
    the bond->force_primary setting, from Xiangning Yu.

 5) Eliminate possible padding beyone end of SKB in cdc_ncm driver, from
    Bjørn Mork.

 6) RX queue length reported for UDP sockets in procfs and socket diag
    are inaccurate, from Paolo Abeni.

 7) Fix br_fdb_find_port() locking, from Petr Machata.

 8) Limit sk_rcvlowat values properly in TCP, from Soheil Hassas
    Yeganeh.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
  tcp: limit sk_rcvlowat by the maximum receive buffer
  net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
  socket: close race condition between sock_close() and sockfs_setattr()
  net: bridge: Fix locking in br_fdb_find_port()
  udp: fix rx queue len reported by diag and proc interface
  cdc_ncm: avoid padding beyond end of skb
  net/sched: act_simple: fix parsing of TCA_DEF_DATA
  net: fddi: fix a possible null-ptr-deref
  net: aquantia: fix unsigned numvecs comparison with less than zero
  net: stmmac: fix build failure due to missing COMMON_CLK dependency
  bpfilter: fix race in pipe access
  bpf, xdp: fix crash in xdp_umem_unaccount_pages
  xsk: Fix umem fill/completion queue mmap on 32-bit
  tools/bpf: fix selftest get_cgroup_id_user
  bpfilter: fix OUTPUT_FORMAT
  umh: fix race condition
  net: mscc: ocelot: Fix uninitialized error in ocelot_netdevice_event()
  bonding: re-evaluate force_primary when the primary slave name changes
  ip_tunnel: Fix name string concatenate in __ip_tunnel_create()
  hv_netvsc: Fix a network regression after ifdown/ifup
  ...

Pull RTC updates from Alexandre Belloni:
 "Setting the supported range from drivers for RTCs failing soon has
  started. A few fixes are developed along the way. Some drivers have
  been switched to SPDX by their maintainers.

  Subsystem:

   - rework of the rtc-test driver which allows to test the core more
     thoroughly

   - rtc_set_alarm() now fails early when alarms are not supported

  Drivers:

   - mktime() is now replaced by mktime64()

   - RTC range added for 88pm80x, ab-b5ze-s3, at91rm9200,
     brcmstb-waketimer, ds1685, ftrtc010, ls1x, mxc_v2, rx8581, sprd,
     st-lpc, tps6586x, tps65910 and vr41xx

   - fixed a possible race condition in probe functions

   - pxa: fix the probe function that is broken since v4.3

   - stm32: now supports stm32mp1"

* tag 'rtc-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (78 commits)
  rtc: pxa: fix probe function
  rtc: cros-ec: Switch to SPDX identifier.
  rtc: cros-ec: Make license text and module license match.
  rtc: ensure rtc_set_alarm fails when alarms are not supported
  rtc: test: remove alarm support from the first device
  rtc: test: convert to devm_rtc_allocate_device
  rtc: ftrtc010: let the core handle range
  rtc: ftrtc010: handle dates after 2106
  rtc: ftrtc010: switch to devm_rtc_allocate_device
  rtc: mrst: switch to devm functions
  rtc: sunxi: fix possible race condition
  rtc: test: remove irq sysfs file
  rtc: test: emulate alarms using timers
  rtc: test: store time as an offset to system time
  rtc: test: allow registering many devices
  rtc: test: remove useless proc info
  rtc: ds1685: Add range
  rtc: ds1685: fix possible race condition
  rtc: sprd: Add new RTC power down check method
  rtc: sun6i: Fix bit_idx value for clk_register_gate
  ...

Pull UBI and UBIFS updates from Richard Weinberger:

 - the UBI on-disk format header file is now dual licensed

 - new way to detect Fastmap problems during runtime

 - bugfix for Fastmap

 - minor updates for UBIFS (spelling, comments, vm_fault_t, ...)

* tag 'upstream-4.18-rc1' of git://git.infradead.org/linux-ubifs:
  mtd: ubi: Update ubi-media.h to dual license
  ubi: fastmap: Detect EBA mismatches on-the-fly
  ubi: fastmap: Check each mapping only once
  ubi: fastmap: Correctly handle interrupted erasures in EBA
  ubi: fastmap: Cancel work upon detach
  ubifs: lpt: Fix wrong pnode number range in comment
  ubifs: gc: Fix typo
  ubifs: log: Some spelling fixes
  ubifs: Spelling fix someting -> something
  ubifs: journal: Remove wrong comment
  ubifs: remove set but never used variable
  ubifs, xattr: remove misguided quota flags
  fs: ubifs: Adding new return type vm_fault_t

The user-provided value to setsockopt(SO_RCVLOWAT) can be
larger than the maximum possible receive buffer. Such values
mute POLLIN signals on the socket which can stall progress
on the socket.

Limit the user-provided value to half of the maximum receive
buffer, i.e., half of sk_rcvbuf when the receive buffer size
is set by the user, or otherwise half of sysctl_tcp_rmem[2].

Fixes: d1361840 ("tcp: fix SO_RCVLOWAT and RCVBUF autotuning")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull SCSI updates from James Bottomley:
 "This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
  xfcp, hisi_sas, cxlflash, qla2xxx.

  In the absence of Nic, we're also taking target updates which are
  mostly minor except for the tcmu refactor.

  The only real core change to worry about is the removal of high page
  bouncing (in sas, storvsc and iscsi). This has been well tested and no
  problems have shown up so far"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
  scsi: lpfc: update driver version to 12.0.0.4
  scsi: lpfc: Fix port initialization failure.
  scsi: lpfc: Fix 16gb hbas failing cq create.
  scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
  scsi: lpfc: correct oversubscription of nvme io requests for an adapter
  scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
  scsi: hisi_sas: Mark PHY as in reset for nexus reset
  scsi: hisi_sas: Fix return value when get_free_slot() failed
  scsi: hisi_sas: Terminate STP reject quickly for v2 hw
  scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
  scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
  scsi: hisi_sas: Try wait commands before before controller reset
  scsi: hisi_sas: Init disks after controller reset
  scsi: hisi_sas: Create a scsi_host_template per HW module
  scsi: hisi_sas: Reset disks when discovered
  scsi: hisi_sas: Add LED feature for v3 hw
  scsi: hisi_sas: Change common allocation mode of device id
  scsi: hisi_sas: change slot index allocation mode
  scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
  scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
  ...

DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.

The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.

Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.

[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fchownat() doesn't even hold refcnt of fd until it figures out
fd is really needed (otherwise is ignored) and releases it after
it resolves the path. This means sock_close() could race with
sockfs_setattr(), which leads to a NULL pointer dereference
since typically we set sock->sk to NULL in ->release().

As pointed out by Al, this is unique to sockfs. So we can fix this
in socket layer by acquiring inode_lock in sock_close() and
checking against NULL in sockfs_setattr().

sock_release() is called in many places, only the sock_close()
path matters here. And fortunately, this should not affect normal
sock_close() as it is only called when the last fd refcnt is gone.
It only affects sock_close() with a parallel sockfs_setattr() in
progress, which is not common.

Fixes: 86741ec2 ("net: core: Add a UID field to struct sock.")
Reported-by: shankarapailoor <shankarapailoor@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull cifs fixes from Steve French:

 - one smb3 (ACL related) fix for stable

 - one SMB3 security enhancement (when mounting -t smb3 forbid less
   secure dialects)

 - some RDMA and compounding fixes

* tag '4.18-fixes-smb3' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix a buffer leak in smb2_query_symlink
  smb3: do not allow insecure cifs mounts when using smb3
  CIFS: Fix NULL ptr deref
  CIFS: fix encryption in SMB3.1.1
  CIFS: Pass page offset for encrypting
  CIFS: Pass page offset for calculating signature
  CIFS: SMBD: Support page offset in memory registration
  CIFS: SMBD: Support page offset in RDMA recv
  CIFS: SMBD: Support page offset in RDMA send
  CIFS: When sending data on socket, pass the correct page offset
  CIFS: Introduce helper function to get page offset and length in smb_rqst
  CIFS: Calculate the correct request length based on page offset and tail size
  cifs: For SMB2 security informaion query, check for minimum sized security descriptor instead of sizeof FileAllInformation class
  CIFS: Fix signing for SMB2/3

Pull block flush handling fix from Jens Axboe:
 "Single fix that we should merge now, fixing a regression in queuing
  flush request, accessing request flags after calling the end_request
  handler"

* tag 'for-linus-20180610' of git://git.kernel.dk/linux-block:
  block: fix use-after-free in block flush handling

Pull restartable sequence support from Thomas Gleixner:
 "The restartable sequences syscall (finally):

  After a lot of back and forth discussion and massive delays caused by
  the speculative distraction of maintainers, the core set of
  restartable sequences has finally reached a consensus.

  It comes with the basic non disputed core implementation along with
  support for arm, powerpc and x86 and a full set of selftests

  It was exposed to linux-next earlier this week, so it does not fully
  comply with the merge window requirements, but there is really no
  point to drag it out for yet another cycle"

* 'core-rseq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rseq/selftests: Provide Makefile, scripts, gitignore
  rseq/selftests: Provide parametrized tests
  rseq/selftests: Provide basic percpu ops test
  rseq/selftests: Provide basic test
  rseq/selftests: Provide rseq library
  selftests/lib.mk: Introduce OVERRIDE_TARGETS
  powerpc: Wire up restartable sequences system call
  powerpc: Add syscall detection for restartable sequences
  powerpc: Add support for restartable sequences
  x86: Wire up restartable sequence system call
  x86: Add support for restartable sequences
  arm: Wire up restartable sequences system call
  arm: Add syscall detection for restartable sequences
  arm: Add restartable sequences support
  rseq: Introduce restartable sequences system call
  uapi/headers: Provide types_32_64.h