This verifies that SECCOMP_RET_KILL_PROCESS is higher priority than
SECCOMP_RET_KILL_THREAD. (This also moves a bunch of defines up earlier
in the file to use them earlier.)
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>

Right now, SECCOMP_RET_KILL_THREAD (neé SECCOMP_RET_KILL) kills the
current thread. There have been a few requests for this to kill the entire
process (the thread group). This cannot be just changed (discovered when
adding coredump support since coredumping kills the entire process)
because there are userspace programs depending on the thread-kill
behavior.

Instead, implement SECCOMP_RET_KILL_PROCESS, which is 0x80000000, and can
be processed as "-1" by the kernel, below the existing RET_KILL that is
ABI-set to "0". For userspace, SECCOMP_RET_ACTION_FULL is added to expand
the mask to the signed bit. Old userspace using the SECCOMP_RET_ACTION
mask will see SECCOMP_RET_KILL_PROCESS as 0 still, but this would only
be visible when examining the siginfo in a core dump from a RET_KILL_*,
where it will think it was thread-killed instead of process-killed.

Attempts to introduce this behavior via other ways (filter flags,
seccomp struct flags, masked RET_DATA bits) all come with weird
side-effects and baggage. This change preserves the central behavioral
expectations of the seccomp filter engine without putting too great
a burden on changes needed in userspace to use the new action.

The new action is discoverable by userspace through either the new
actions_avail sysctl or through the SECCOMP_GET_ACTION_AVAIL seccomp
operation. If used without checking for availability, old kernels
will treat RET_KILL_PROCESS as RET_KILL_THREAD (since the old mask
will produce RET_KILL_THREAD).

Cc: Paul Moore <paul@paul-moore.com>
Cc: Fabricio Voznika <fvoznika@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

This introduces the BPF return value for SECCOMP_RET_KILL_PROCESS to kill
an entire process. This cannot yet be reached by seccomp, but it changes
the default-kill behavior (for unknown return values) from kill-thread to
kill-process.
Signed-off-by: Kees Cook <keescook@chromium.org>

In preparation for adding SECCOMP_RET_KILL_PROCESS, rename SECCOMP_RET_KILL
to the more accurate SECCOMP_RET_KILL_THREAD.

The existing selftest values are intentionally left as SECCOMP_RET_KILL
just to be sure we're exercising the alias.
Signed-off-by: Kees Cook <keescook@chromium.org>

Add a new action, SECCOMP_RET_LOG, that logs a syscall before allowing
the syscall. At the implementation level, this action is identical to
the existing SECCOMP_RET_ALLOW action. However, it can be very useful when
initially developing a seccomp filter for an application. The developer
can set the default action to be SECCOMP_RET_LOG, maybe mark any
obviously needed syscalls with SECCOMP_RET_ALLOW, and then put the
application through its paces. A list of syscalls that triggered the
default action (SECCOMP_RET_LOG) can be easily gleaned from the logs and
that list can be used to build the syscall whitelist. Finally, the
developer can change the default action to the desired value.

This provides a more friendly experience than seeing the application get
killed, then updating the filter and rebuilding the app, seeing the
application get killed due to a different syscall, then updating the
filter and rebuilding the app, etc.

The functionality is similar to what's supported by the various LSMs.
SELinux has permissive mode, AppArmor has complain mode, SMACK has
bring-up mode, etc.

SECCOMP_RET_LOG is given a lower value than SECCOMP_RET_ALLOW as allow
while logging is slightly more restrictive than quietly allowing.

Unfortunately, the tests added for SECCOMP_RET_LOG are not capable of
inspecting the audit log to verify that the syscall was logged.

With this patch, the logic for deciding if an action will be logged is:

if action == RET_ALLOW:
  do not log
else if action == RET_KILL && RET_KILL in actions_logged:
  log
else if action == RET_LOG && RET_LOG in actions_logged:
  log
else if filter-requests-logging && action in actions_logged:
  log
else if audit_enabled && process-is-being-audited:
  log
else:
  do not log
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Add a new filter flag, SECCOMP_FILTER_FLAG_LOG, that enables logging for
all actions except for SECCOMP_RET_ALLOW for the given filter.

SECCOMP_RET_KILL actions are always logged, when "kill" is in the
actions_logged sysctl, and SECCOMP_RET_ALLOW actions are never logged,
regardless of this flag.

This flag can be used to create noisy filters that result in all
non-allowed actions to be logged. A process may have one noisy filter,
which is loaded with this flag, as well as a quiet filter that's not
loaded with this flag. This allows for the actions in a set of filters
to be selectively conveyed to the admin.

Since a system could have a large number of allocated seccomp_filter
structs, struct packing was taken in consideration. On 64 bit x86, the
new log member takes up one byte of an existing four byte hole in the
struct. On 32 bit x86, the new log member creates a new four byte hole
(unavoidable) and consumes one of those bytes.

Unfortunately, the tests added for SECCOMP_FILTER_FLAG_LOG are not
capable of inspecting the audit log to verify that the actions taken in
the filter were logged.

With this patch, the logic for deciding if an action will be logged is:

if action == RET_ALLOW:
  do not log
else if action == RET_KILL && RET_KILL in actions_logged:
  log
else if filter-requests-logging && action in actions_logged:
  log
else if audit_enabled && process-is-being-audited:
  log
else:
  do not log
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Userspace needs to be able to reliably detect the support of a filter
flag. A good way of doing that is by attempting to enter filter mode,
with the flag bit(s) in question set, and a NULL pointer for the args
parameter of seccomp(2). EFAULT indicates that the flag is valid and
EINVAL indicates that the flag is invalid.

This patch adds a selftest that can be used to test this method of
detection in userspace.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Adminstrators can write to this sysctl to set the seccomp actions that
are allowed to be logged. Any actions not found in this sysctl will not
be logged.

For example, all SECCOMP_RET_KILL, SECCOMP_RET_TRAP, and
SECCOMP_RET_ERRNO actions would be loggable if "kill trap errno" were
written to the sysctl. SECCOMP_RET_TRACE actions would not be logged
since its string representation ("trace") wasn't present in the sysctl
value.

The path to the sysctl is:

 /proc/sys/kernel/seccomp/actions_logged

The actions_avail sysctl can be read to discover the valid action names
that can be written to the actions_logged sysctl with the exception of
"allow". SECCOMP_RET_ALLOW actions cannot be configured for logging.

The default setting for the sysctl is to allow all actions to be logged
except SECCOMP_RET_ALLOW. While only SECCOMP_RET_KILL actions are
currently logged, an upcoming patch will allow applications to request
additional actions to be logged.

There's one important exception to this sysctl. If a task is
specifically being audited, meaning that an audit context has been
allocated for the task, seccomp will log all actions other than
SECCOMP_RET_ALLOW despite the value of actions_logged. This exception
preserves the existing auditing behavior of tasks with an allocated
audit context.

With this patch, the logic for deciding if an action will be logged is:

if action == RET_ALLOW:
  do not log
else if action == RET_KILL && RET_KILL in actions_logged:
  log
else if audit_enabled && task-is-being-audited:
  log
else:
  do not log
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Userspace code that needs to check if the kernel supports a given action
may not be able to use the /proc/sys/kernel/seccomp/actions_avail
sysctl. The process may be running in a sandbox and, therefore,
sufficient filesystem access may not be available. This patch adds an
operation to the seccomp(2) syscall that allows userspace code to ask
the kernel if a given action is available.

If the action is supported by the kernel, 0 is returned. If the action
is not supported by the kernel, -1 is returned with errno set to
-EOPNOTSUPP. If this check is attempted on a kernel that doesn't support
this new operation, -1 is returned with errno set to -EINVAL meaning
that userspace code will have the ability to differentiate between the
two error cases.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Kees Cook <keescook@chromium.org>

This patch creates a read-only sysctl containing an ordered list of
seccomp actions that the kernel supports. The ordering, from left to
right, is the lowest action value (kill) to the highest action value
(allow). Currently, a read of the sysctl file would return "kill trap
errno trace allow". The contents of this sysctl file can be useful for
userspace code as well as the system administrator.

The path to the sysctl is:

  /proc/sys/kernel/seccomp/actions_avail

libseccomp and other userspace code can easily determine which actions
the current kernel supports. The set of actions supported by the current
kernel may be different than the set of action macros found in kernel
headers that were installed where the userspace code was built.

In addition, this sysctl will allow system administrators to know which
actions are supported by the kernel and make it easier to configure
exactly what seccomp logs through the audit subsystem. Support for this
level of logging configuration will come in a future patch.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Both the upcoming logging improvements and changes to RET_KILL will need
to know which filter a given seccomp return value originated from. In
order to delay logic processing of result until after the seccomp loop,
this adds a single pointer assignment on matches. This will allow both
log and RET_KILL logic to work off the filter rather than doing more
expensive tests inside the time-critical run_filters loop.

Running tight cycles of getpid() with filters attached shows no measurable
difference in speed.
Suggested-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>

This refactors the errno tests (since they all use the same pattern for
their filter) and adds a RET_DATA field ordering test.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>

This attempts to produce a comparison between native getpid() and a
RET_ALLOW-filtered getpid(), to measure the overhead cost of using
seccomp().
Signed-off-by: Kees Cook <keescook@chromium.org>

This adds tests for using only ptrace to perform syscall changes, just
to validate matching behavior between seccomp events and ptrace events.
Signed-off-by: Kees Cook <keescook@chromium.org>

This adds a perl script to actually parse the MAINTAINERS file, clean up
some whitespace in it, warn about errors in it, and then properly sort
the end result.

My perl-fu is atrocious, so the script has basically been created by
randomly putting various characters in a pile, mixing them around, and
then looking it the end result does anything interesting when used as a
perl script.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prepping for scripting the MAINTAINERS file cleanup (and possible split)
showed a couple of cases where the headers for a couple of entries were
bogus.

There's a few different kinds of bogosities:

 - the X-GENE SOC EDAC case was confused and split over two lines

 - there were four entries for "GREYBUS PROTOCOLS DRIVERS" that were all
   different things.

 - the NOKIA N900 CAMERA SUPPORT" was duplicated

all of which were more obvious when you started doing associative arrays
in perl to track these things by the header (so that we can alphabetize
this thing properly, and so that we might split it up by the data too).

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xen fixes from Juergen Gross:
 "Some fixes and cleanups for running under Xen"

* tag 'for-linus-4.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't online new memory initially
  xen/x86: fix cpu hotplug
  xen/grant-table: log the lack of grants
  xen/x86: Don't BUG on CPU0 offlining

When setting up the Xenstore watch for the memory target size the new
watch will fire at once. Don't try to reach the configured target size
by onlining new memory in this case, as the current memory size will
be smaller in almost all cases due to e.g. BIOS reserved pages.

Onlining new memory will lead to more problems e.g. undesired conflicts
with NVMe devices meant to be operated as block devices.

Instead remember the difference between target size and current size
when the watch fires for the first time and apply it to any further
size changes, too.

In order to avoid races between balloon.c and xen-balloon.c init calls
do the xen-balloon.c initialization from balloon.c.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

Commit dc6416f1 ("xen/x86: Call
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()")
introduced an error leading to a stack overflow of the idle task when
a cpu was brought offline/online many times: by calling
cpu_startup_entry() instead of returning at the end of xen_play_dead()
do_idle() would be entered again and again.

Don't use cpu_startup_entry(), but cpuhp_online_idle() instead allowing
to return from xen_play_dead().

Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

log a message when we enter this situation:
1) we already allocated the max number of available grants from hypervisor
and
2) we still need more (but the request fails because of 1)).

Sometimes the lack of grants causes IO hangs in xen_blkfront devices.
Adding this log would help debuging.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

CONFIG_BOOTPARAM_HOTPLUG_CPU0 allows to offline CPU0 but Xen HVM guests
BUG() in xen_teardown_timer(). Remove the BUG_ON(), this is probably a
leftover from ancient times when CPU0 hotplug was impossible, it works
just fine for HVM.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

Merge tag 'hwmon-for-linus-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Avoid buffer overruns in applesmc driver"

* tag 'hwmon-for-linus-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (applesmc) Avoid buffer overruns

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
  huge at all, a revert of a patch that turned out to break things, a
  fix up for a new tty ioctl we added in 4.13-rc1 to get the uapi
  definition correct, and a few minor serial driver fixes for reported
  issues.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix TIOCGPTPEER ioctl definition
  tty: hide unused pty_get_peer function
  tty: serial: lpuart: Fix the logic for detecting the 32-bit type UART
  serial: imx: Prevent TX buffer PIO write when a DMA has been started
  Revert "serial: imx-serial - move DMA buffer configuration to DT"
  serial: sh-sci: Uninitialized variables in sysfs files
  serial: st-asc: Potential error pointer dereference

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 4.13-rc2. All fix
  reported problems with 4.13-rc1 or older kernels (like the binder
  fixes). Full details in the shortlog.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  w1: omap-hdq: fix error return code in omap_hdq_probe()
  regmap: regmap-w1: Fix build troubles
  w1: Fix slave count on 1-Wire bus (resend)
  mux: mux-core: unregister mux_class in mux_exit()
  mux: remove the Kconfig question for the subsystem
  nvmem: rockchip-efuse: amend compatible rk322x-efuse to rk3228-efuse
  drivers/fsi: fix fsi_slave_mode prototype
  fsi: core: register with postcore_initcall
  thunderbolt: Correct access permissions for active NVM contents
  vmbus: re-enable channel tasklet
  spmi: pmic-arb: Always allocate ppid_to_apid table
  MAINTAINERS: Add entry for SPMI subsystem
  spmi: Include OF based modalias in device uevent
  binder: Use wake up hint for synchronous transactions.
  binder: use group leader instead of open thread
  Revert "android: binder: Sanity check at binder ioctl"

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.13-rc2.

  The usual batch, gadget fixes for reported issues, as well as xhci
  fixes, and a small random collection of other fixes for reported
  issues.

  All have been in linux-next with no reported issues"

* tag 'usb-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  xhci: fix memleak in xhci_run()
  usb: xhci: fix spinlock recursion for USB2 test mode
  xhci: fix 20000ms port resume timeout
  usb: xhci: Issue stop EP command only when the EP state is running
  xhci: Bad Ethernet performance plugged in ASM1042A host
  xhci: Fix NULL pointer dereference when cleaning up streams for removed host
  usb: renesas_usbhs: gadget: disable all eps when the driver stops
  usb: renesas_usbhs: fix usbhsc_resume() for !USBHSF_RUNTIME_PWCTRL
  usb: gadget: udc: renesas_usb3: protect usb3_ep->started in usb3_start_pipen()
  usb: gadget: udc: renesas_usb3: fix zlp transfer by the dmac
  usb: gadget: udc: renesas_usb3: fix free size in renesas_usb3_dma_free_prd()
  usb: gadget: f_uac2: endianness fixes.
  usb: gadget: f_uac1: endianness fixes.
  include: usb: audio: specify exact endiannes of descriptors
  usb: gadget: udc: start_udc() can be static
  usb: dwc2: gadget: On USB RESET reset device address to zero
  usb: storage: return on error to avoid a null pointer dereference
  usb: typec: include linux/device.h in ucsi.h
  USB: cdc-acm: add device-id for quirky printer
  usb: dwc3: gadget: only unmap requests from DMA if mapped
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for reported issues for
  4.13-rc2.

  Also in here is a new driver, the virtualbox DRM driver. It's
  stand-alone and got acks from the DRM developers to go in through this
  tree. It's a new thing, but it should be fine for this point in the rc
  cycle due to it being independent.

  All of this has been in linux-next for a while with no reported
  issues"

* tag 'staging-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8188eu: add TL-WN722N v2 support
  staging: speakup: safely register and unregister ldisc
  staging: speakup: add functions to register and unregister ldisc
  staging: speakup: safely close tty
  staging: sm750fb: avoid conflicting vesafb
  staging: lustre: ko2iblnd: check copy_from_iter/copy_to_iter return code
  staging: vboxvideo: Add vboxvideo to drivers/staging
  staging: sm750fb: fixed a assignment typo
  staging: rtl8188eu: memory leak in rtw_free_cmd_obj()
  staging: vchiq_arm: fix error codes in probe
  staging: comedi: ni_mio_common: fix AO timer off-by-one regression

Fix major alphabetic errors.  No attempt to fix items that all begin
with the same word (like ARM, BROADCOM, DRM, EDAC, FREESCALE, INTEL,
OMAP, PCI, SAMSUNG, TI, USB, etc.).

(diffstat +/- is different by one line because TI KEYSTONE MULTICORE
had 2 blank lines after it.)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NFS client bugfixes from Anna Schumaker:
 "Stable bugfix:
   - Fix error reporting regression

  Bugfixes:
   - Fix setting filelayout ds address race
   - Fix subtle access bug when using ACLs
   - Fix setting mnt3_counts array size
   - Fix a couple of pNFS commit races"

* tag 'nfs-for-4.13-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS/filelayout: Fix racy setting of fl->dsaddr in filelayout_check_deviceid()
  NFS: Be more careful about mapping file permissions
  NFS: Store the raw NFS access mask in the inode's access cache
  NFSv3: Convert nfs3_proc_access() to use nfs_access_set_mask()
  NFS: Refactor NFS access to kernel access mask calculation
  net/sunrpc/xprt_sock: fix regression in connection error reporting.
  nfs: count correct array for mnt3_counts array size
  Revert commit 722f0b89 ("pNFS: Don't send COMMITs to the DSes if...")
  pNFS/flexfiles: Handle expired layout segments in ff_layout_initiate_commit()
  NFS: Fix another COMMIT race in pNFS
  NFS: Fix a COMMIT race in pNFS
  mount: copy the port field into the cloned nfs_server structure.
  NFS: Don't run wake_up_bit() when nobody is waiting...
  nfs: add export operations

Pull overlayfs fixes from Miklos Szeredi:
 "This fixes a crash with SELinux and several other old and new bugs"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: check for bad and whiteout index on lookup
  ovl: do not cleanup directory and whiteout index entries
  ovl: fix xattr get and set with selinux
  ovl: remove unneeded check for IS_ERR()
  ovl: fix origin verification of index dir
  ovl: mark parent impure on ovl_link()
  ovl: fix random return value on mount

Pull block fixes from Jens Axboe:
 "A small set of fixes for -rc2 - two fixes for BFQ, documentation and
  code, and a removal of an unused variable in nbd. Outside of that, a
  small collection of fixes from the usual crew on the nvme side"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvmet: don't report 0-bytes in serial number
  nvmet: preserve controller serial number between reboots
  nvmet: Move serial number from controller to subsystem
  nvmet: prefix version configfs file with attr
  nvme-pci: Fix an error handling path in 'nvme_probe()'
  nvme-pci: Remove nvme_setup_prps BUG_ON
  nvme-pci: add another device ID with stripe quirk
  nvmet-fc: fix byte swapping in nvmet_fc_ls_create_association
  nvme: fix byte swapping in the streams code
  nbd: kill unused ret in recv_work
  bfq: dispatch request to prevent queue stalling after the request completion
  bfq: fix typos in comments about B-WF2Q+ algorithm

Pull more rdma fixes from Doug Ledford:
 "As per my previous pull request, there were two drivers that each had
  a rather large number of legitimate fixes still to be sent.

  As it turned out, I also missed a reasonably large set of fixes from
  one person across the stack that are all important fixes. All in all,
  the bnxt_re, i40iw, and Dan Carpenter are 3/4 to 2/3rds of this pull
  request.

  There were some other random fixes that I didn't send in the last pull
  request that I added to this one. This catches the rdma stack up to
  the fixes from up to about the beginning of this week. Any more fixes
  I'll wait and batch up later in the -rc cycle. This will give us a
  good base to start with for basing a for-next branch on -rc2.

  Summary:

   - i40iw fixes

   - bnxt_re fixes

   - Dan Carpenter bugfixes across stack

   - ten more random fixes, no more than two from any one person"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
  RDMA/core: Initialize port_num in qp_attr
  RDMA/uverbs: Fix the check for port number
  IB/cma: Fix reference count leak when no ipv4 addresses are set
  RDMA/iser: don't send an rkey if all data is written as immadiate-data
  rxe: fix broken receive queue draining
  RDMA/qedr: Prevent memory overrun in verbs' user responses
  iw_cxgb4: don't use WR keys/addrs for 0 byte reads
  IB/mlx4: Fix CM REQ retries in paravirt mode
  IB/rdmavt: Setting of QP timeout can overflow jiffies computation
  IB/core: Fix sparse warnings
  RDMA/bnxt_re: Fix the value reported for local ack delay
  RDMA/bnxt_re: Report MISSED_EVENTS in req_notify_cq
  RDMA/bnxt_re: Fix return value of poll routine
  RDMA/bnxt_re: Enable atomics only if host bios supports
  RDMA/bnxt_re: Specify RDMA component when allocating stats context
  RDMA/bnxt_re: Fixed the max_rd_atomic support for initiator and destination QP
  RDMA/bnxt_re: Report supported value to IB stack in query_device
  RDMA/bnxt_re: Do not free the ctx_tbl entry if delete GID fails
  RDMA/bnxt_re: Fix WQE Size posted to HW to prevent it from throwing error
  RDMA/bnxt_re: Free doorbell page index (DPI) during dealloc ucontext
  ...

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for rc2: two imx regressions, vc4 fix, dma-buf fix,
  some displayport mst fixes, and an amdkfd fix.

  Nothing too crazy, I assume we just haven't see much rc1 testing yet"

* tag 'drm-fixes-for-v4.13-rc2' of git://people.freedesktop.org/~airlied/linux:
  drm/mst: Avoid processing partially received up/down message transactions
  drm/mst: Avoid dereferencing a NULL mstb in drm_dp_mst_handle_up_req()
  drm/mst: Fix error handling during MST sideband message reception
  drm/imx: parallel-display: Accept drm_of_find_panel_or_bridge failure
  drm/imx: fix typo in ipu_plane_formats[]
  drm/vc4: Fix VBLANK handling in crtc->enable() path
  dma-buf/fence: Avoid use of uninitialised timestamp
  drm/amdgpu: Remove unused field kgd2kfd_shared_resources.num_mec
  drm/radeon: Remove initialization of shared_resources.num_mec
  drm/amdkfd: Remove unused references to shared_resources.num_mec
  drm/amdgpu: Fix KFD oversubscription by tracking queues correctly

Pull tracing fixes from Steven Rostedt:
 "Three minor updates

   - Use the new GFP_RETRY_MAYFAIL to be more aggressive in allocating
     memory for the ring buffer without causing OOMs

   - Fix a memory leak in adding and removing instances

   - Add __rcu annotation to be able to debug RCU usage of function
     tracing a bit better"

* tag 'trace-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  trace: fix the errors caused by incompatible type of RCU variables
  tracing: Fix kmemleak in instance_rmdir
  tracing/ring_buffer: Try harder to allocate

Pull KVM fixes from Radim Krčmář:
 "A bunch of small fixes for x86"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: x86: hyperv: avoid livelock in oneshot SynIC timers
  KVM: VMX: Fix invalid guest state detection after task-switch emulation
  x86: add MULTIUSER dependency for KVM
  KVM: nVMX: Disallow VM-entry in MOV-SS shadow
  KVM: nVMX: track NMI blocking state separately for each VMCS
  KVM: x86: masking out upper bits

Pull powerpc fixes from Michael Ellerman:
 "A handful of fixes, mostly for new code:

   - some reworking of the new STRICT_KERNEL_RWX support to make sure we
     also remove executable permission from __init memory before it's
     freed.

   - a fix to some recent optimisations to the hypercall entry where we
     were clobbering r12, this was breaking nested guests (PR KVM).

   - a fix for the recent patch to opal_configure_cores(). This could
     break booting on bare metal Power8 boxes if the kernel was built
     without CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG.

   - .. and finally a workaround for spurious PMU interrupts on Power9
     DD2.

  Thanks to: Nicholas Piggin, Anton Blanchard, Balbir Singh"

* tag 'powerpc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Mark __init memory no-execute when STRICT_KERNEL_RWX=y
  powerpc/mm/hash: Refactor hash__mark_rodata_ro()
  powerpc/mm/radix: Refactor radix__mark_rodata_ro()
  powerpc/64s: Fix hypercall entry clobbering r12 input
  powerpc/perf: Avoid spurious PMU interrupts after idle
  powerpc/powernv: Fix boot on Power8 bare metal due to opal_configure_cores()

Pull x86 fixes from Ingo Molnar:
 "Half of the fixes are for various build time warnings triggered by
  randconfig builds. Most (but not all...) were harmless.

  There's also:

   - ACPI boundary condition fixes

   - UV platform fixes

   - defconfig updates

   - an AMD K6 CPU init fix

   - a %pOF printk format related preparatory change

   - .. and a warning fix related to the tlb/PCID changes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/devicetree: Convert to using %pOF instead of ->full_name
  x86/platform/uv/BAU: Disable BAU on single hub configurations
  x86/platform/intel-mid: Fix a format string overflow warning
  x86/platform: Add PCI dependency for PUNIT_ATOM_DEBUG
  x86/build: Silence the build with "make -s"
  x86/io: Add "memory" clobber to insb/insw/insl/outsb/outsw/outsl
  x86/fpu/math-emu: Avoid bogus -Wint-in-bool-context warning
  x86/fpu/math-emu: Fix possible uninitialized variable use
  perf/x86: Shut up false-positive -Wmaybe-uninitialized warning
  x86/defconfig: Remove stale, old Kconfig options
  x86/ioapic: Pass the correct data to unmask_ioapic_irq()
  x86/acpi: Prevent out of bound access caused by broken ACPI tables
  x86/mm, KVM: Fix warning when !CONFIG_PREEMPT_COUNT
  x86/platform/uv/BAU: Fix congested_response_us not taking effect
  x86/cpu: Use indirect call to measure performance in init_amd_k6()

Pull timer fix from Ingo Molnar:
 "A timer_irq_init() clocksource API robustness fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/timer-of: Handle of_irq_get_byname() result correctly

Pull scheduler fixes from Ingo Molnar:
 "A cputime fix and code comments/organization fix to the deadline
  scheduler"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix confusing comments about selection of top pi-waiter
  sched/cputime: Don't use smp_processor_id() in preemptible context

Pull perf fixes from Ingo Molnar:
 "Two hw-enablement patches, two race fixes, three fixes for regressions
  of semantics, plus a number of tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Add proper condition to run sched_task callbacks
  perf/core: Fix locking for children siblings group read
  perf/core: Fix scheduling regression of pinned groups
  perf/x86/intel: Fix debug_store reset field for freq events
  perf/x86/intel: Add Goldmont Plus CPU PMU support
  perf/x86/intel: Enable C-state residency events for Apollo Lake
  perf symbols: Accept zero as the kernel base address
  Revert "perf/core: Drop kernel samples even though :u is specified"
  perf annotate: Fix broken arrow at row 0 connecting jmp instruction to its target
  perf evsel: State in the default event name if attr.exclude_kernel is set
  perf evsel: Fix attr.exclude_kernel setting for default cycles:p