- 16 Aug, 2017 31 commits
-
-
Kai-Heng Feng authored
commit 7496cfe5 upstream. Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to connect to Realtek r8153. The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk can make it work. Since another r8153 dongle at my hand does not have the issue, so add the quirk to the Genesys Logic hub instead. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bin Liu authored
commit 2eac1362 upstream. While unlink an urb, if the urb has been programmed in the controller, the controller driver might do some hw related actions to tear down the urb. Currently usb_hcd_flush_endpoint() passes each urb from the head of the endpoint's urb_list to the controller driver, which could make the controller driver think each urb has been programmed and take the unnecessary actions for each urb. This patch changes the behavior in usb_hcd_flush_endpoint() to pass the urbs from the tail of the list, to avoid any unnecessary actions in an controller driver. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Alan Stern authored
commit 94c43b98 upstream. Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4c ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by:
Zdenek Kabelac <zkabelac@redhat.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Yoshihiro Shimoda authored
commit 2acecd58 upstream. The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit. If the bit sets to 1, the VBUS drive is controlled by phy related registers (called "UCOM Registers" on the manual). Since R-Car Gen3 environment will control VBUS by phy-rcar-gen3-usb2 driver, the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes the register's value. Otherwise, even if the ID pin indicates to peripheral, the R-Car will output USBn_PWEN to 1 when a host driver is running. Fixes: de18757e ("usb: renesas_usbhs: add R-Car Gen3 power control" Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit aca5b9eb upstream. According to the gadget.h, a "complete" function will always be called with interrupts disabled. However, sometimes usb3_request_done() function is called with interrupts enabled. So, this function should be held by spin_lock_irqsave() to disable interruption. Also, this driver has to call spin_unlock() to avoid spinlock recursion by this driver before calling usb_gadget_giveback_request(). Reported-by:
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Tested-by:
-
Alan Swanson authored
commit 89f23d51 upstream. Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by:
Alan Swanson <reiver@improbability.net> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Ian Abbott authored
commit cef98864 upstream. Comedi's read and write file operation handlers (`comedi_read()` and `comedi_write()`) currently call `copy_to_user()` or `copy_from_user()` whilst in the `TASK_INTERRUPTIBLE` state, which falls foul of the `might_fault()` checks when enabled. Fix it by setting the current task state back to `TASK_RUNNING` a bit earlier before calling these functions. Reported-by:
Piotr Gregor <piotrgregor@rsyncme.org> Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Akinobu Mita authored
commit a3507e48 upstream. The TSL2563 driver provides three iio channels, two of which are raw ADC channels (channel 0 and channel 1) in the device and the remaining one is calculated by the two. The ADC channel 0 only supports programmable interrupt with threshold settings and this driver supports the event but the generated event code does not contain the corresponding iio channel type. This is going to change userspace ABI. Hopefully fixing this to be what it should always have been won't break any userspace code. Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit e59e1898 upstream. After probe we would put the device in normal mode, after a runtime suspend-resume we would put it back in normal mode. But for a regular suspend-resume we would only put it back in normal mode if triggers or events have been requested. This is not consistent and breaks reading raw values after a suspend-resume. This commit changes the regular resume path to also unconditionally put the device back in normal mode, fixing reading of raw values not working after a regular suspend-resume cycle. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Arnd Bergmann authored
commit 105967ad upstream. gcc-7 points out an older regression: drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw': drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] The original code had 'unsigned short' here, but incorrectly got converted to 'bool'. This reverts the regression and uses a normal type instead. Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Rafael J. Wysocki authored
commit cd5a6a4f upstream. Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Bin Liu authored
commit 45d73860 upstream. commit 68fe05e2 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Signed-off-by:
-
Greg Kroah-Hartman authored
commit 3b6bcd3d upstream. This adds a new ATEN device id for a new pl2303-based device. Reported-by:
Peter Kuo <PeterKuo@aten.com.tw> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Stefan Triller authored
commit 9585e340 upstream. The German Telekom offers a ZigBee USB Stick under the brand name Qivicon for their SmartHome Home Base in its 1. Generation. The productId is not known by the according kernel module, this patch adds support for it. Signed-off-by:
Stefan Triller <github@stefantriller.de> Reviewed-by:
Frans Klaver <fransklaver@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hector Martin authored
commit fd1b8668 upstream. Add device id for D-Link DWM-222. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Maarten Lankhorst authored
commit 5279fc77 upstream. bdw_load_gamma_lut is writing beyond the array to the maximum value. The intend of the function is to clamp values > 1 to 1, so write the intended color to the max register. This fixes the following KASAN warning: [ 197.020857] [IGT] kms_pipe_color: executing [ 197.063434] [IGT] kms_pipe_color: starting subtest ctm-0-25-pipe0 [ 197.078989] ================================================================== [ 197.079127] BUG: KASAN: slab-out-of-bounds in bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079188] Read of size 2 at addr ffff8800d38db150 by task kms_pipe_color/1839 [ 197.079208] CPU: 2 PID: 1839 Comm: kms_pipe_color Tainted: G U 4.13.0-rc1-patser+ #5211 [ 197.079215] Hardware name: NUC5i7RYB, BIOS RYBDWi35.86A.0246.2015.0309.1355 03/09/2015 [ 197.079220] Call Trace: [ 197.079230] dump_stack+0x68/0x9e [ 197.079239] print_address_description+0x6f/0x250 [ 197.079251] kasan_report+0x216/0x370 [ 197.079374] ? bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079451] ? gen8_write16+0x4e0/0x4e0 [i915] [ 197.079460] __asan_report_load2_noabort+0x14/0x20 [ 197.079535] bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079612] broadwell_load_luts+0x1df/0x550 [i915] [ 197.079690] intel_color_load_luts+0x7b/0x80 [i915] [ 197.079764] intel_begin_crtc_commit+0x138/0x760 [i915] [ 197.079783] drm_atomic_helper_commit_planes_on_crtc+0x1a3/0x820 [drm_kms_helper] [ 197.079859] ? intel_pre_plane_update+0x571/0x580 [i915] [ 197.079937] intel_update_crtc+0x238/0x330 [i915] [ 197.080016] intel_update_crtcs+0x10f/0x210 [i915] [ 197.080092] intel_atomic_commit_tail+0x1552/0x3340 [i915] [ 197.080101] ? _raw_spin_unlock+0x3c/0x40 [ 197.080110] ? __queue_work+0xb40/0xbf0 [ 197.080188] ? skl_update_crtcs+0xc00/0xc00 [i915] [ 197.080195] ? trace_hardirqs_on+0xd/0x10 [ 197.080269] ? intel_atomic_commit_ready+0x128/0x13c [i915] [ 197.080329] ? __i915_sw_fence_complete+0x5b8/0x6d0 [i915] [ 197.080336] ? debug_object_activate+0x39e/0x580 [ 197.080397] ? i915_sw_fence_await+0x30/0x30 [i915] [ 197.080409] ? __might_sleep+0x15b/0x180 [ 197.080483] intel_atomic_commit+0x944/0xa70 [i915] [ 197.080490] ? refcount_dec_and_test+0x11/0x20 [ 197.080567] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080597] ? drm_atomic_crtc_set_property+0x303/0x580 [drm] [ 197.080674] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080704] drm_atomic_commit+0xd7/0xe0 [drm] [ 197.080722] drm_atomic_helper_crtc_set_property+0xec/0x130 [drm_kms_helper] [ 197.080749] drm_mode_crtc_set_obj_prop+0x7d/0xb0 [drm] [ 197.080775] drm_mode_obj_set_property_ioctl+0x50b/0x5d0 [drm] [ 197.080783] ? __might_fault+0x104/0x180 [ 197.080809] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080838] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080861] drm_ioctl_kernel+0x154/0x1a0 [drm] [ 197.080885] drm_ioctl+0x624/0x8f0 [drm] [ 197.080910] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080934] ? drm_getunique+0x210/0x210 [drm] [ 197.080943] ? __handle_mm_fault+0x1bd0/0x1ce0 [ 197.080949] ? lock_downgrade+0x610/0x610 [ 197.080957] ? __lru_cache_add+0x15a/0x180 [ 197.080967] do_vfs_ioctl+0xd92/0xe40 [ 197.080975] ? ioctl_preallocate+0x1b0/0x1b0 [ 197.080982] ? selinux_capable+0x20/0x20 [ 197.080991] ? __do_page_fault+0x7b7/0x9a0 [ 197.080997] ? lock_downgrade+0x5bb/0x610 [ 197.081007] ? security_file_ioctl+0x57/0x90 [ 197.081016] SyS_ioctl+0x4e/0x80 [ 197.081024] entry_SYSCALL_64_fastpath+0x18/0xad [ 197.081030] RIP: 0033:0x7f61f287a987 [ 197.081035] RSP: 002b:00007fff7d44d188 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 197.081043] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f61f287a987 [ 197.081048] RDX: 00007fff7d44d1c0 RSI: 00000000c01864ba RDI: 0000000000000003 [ 197.081053] RBP: 00007f61f2b3eb00 R08: 0000000000000059 R09: 0000000000000000 [ 197.081058] R10: 0000002ea5c4a290 R11: 0000000000000246 R12: 00007f61f2b3eb58 [ 197.081063] R13: 0000000000001010 R14: 00007f61f2b3eb58 R15: 0000000000002702 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101659Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reported-by:
Martin Peres <martin.peres@linux.intel.com> Cc: Martin Peres <martin.peres@linux.intel.com> Fixes: 82cf435b ("drm/i915: Implement color management on bdw/skl/bxt/kbl") Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Kiran S Kumar <kiran.s.kumar@intel.com> Cc: Kausal Malladi <kausalmalladi@gmail.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20170724091431.24251-1-maarten.lankhorst@linux.intel.comReviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> (cherry picked from commit 09a92bc8) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Wladimir J. van der Laan authored
commit d6f756e0 upstream. A relocation pointing to the last four bytes of a buffer can legitimately happen in the case of small vertex buffers. Signed-off-by:
Wladimir J. van der Laan <laanwj@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Weston Andros Adamson authored
commit 1feb2616 upstream. The client was freeing the nfs4_ff_layout_ds, but not the contained nfs4_ff_ds_version array. Signed-off-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Haibo Chen authored
commit 92ddd959 upstream. Change the default err value to -EINVAL, make sure the card only has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage setting when select hs400es mode. Fixes: commit 1720d354 ("mmc: core: switch to 1V8 or 1V2 for hs400es mode") Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Miquel Raynal authored
commit f7f8c175 upstream. When using soft ecc, if no ooblayout is given, the core automatically uses one of the nand_ooblayout_{sp,lp}*() functions to determine the layout inside the out of band data. Until kernel version 4.6, struct nand_ecclayout was used for that purpose. During the migration from 4.6 to 4.7, an error shown up in the small page layout, in the case oob section is only 8 bytes long. The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4) as free bytes, one byte (5) for bad block marker and finally two bytes (6, 7) as free bytes, as shown there: [linux-4.6] drivers/mtd/nand/nand_base.c:52 static struct nand_ecclayout nand_oob_8 = { .eccbytes = 3, .eccpos = {0, 1, 2}, .oobfree = { {.offset = 3, .length = 2}, {.offset = 6, .length = 2} } }; This fixes the current implementation which is incoherent. It references bit 3 at the same time as an ecc byte and a free byte. Furthermore, it is clear with the previous implementation that there is only one ecc section with 8 bytes oob sections. We shall return -ERANGE in the nand_ooblayout_ecc_sp() function when asked for the second section. Signed-off-by:
Miquel Raynal <miquel.raynal@free-electrons.com> Fixes: 41b207a7 ("mtd: nand: implement the default mtd_ooblayout_ops") Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Mateusz Jurczyk authored
commit 68227c03 upstream. Before the patch, the flock flag could remain uninitialized for the lifespan of the fuse_file allocation. Unless set to true in fuse_file_flock(), it would remain in an indeterminate state until read in an if statement in fuse_release_common(). This could consequently lead to taking an unexpected branch in the code. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Fixes: 37fb3a30 ("fuse: fix flock") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 6f48655f upstream. This patch fixes a generate_node_acls = 1 + cache_dynamic_acls = 0 regression, that was introduced by commit 01d4d673 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Wed Dec 7 12:55:54 2016 -0800 which originally had the proper list_del_init() usage, but was dropped during list review as it was thought unnecessary by HCH. However, list_del_init() usage is required during the special generate_node_acls = 1 + cache_dynamic_acls = 0 case when transport_free_session() does a list_del(&se_nacl->acl_list), followed by target_complete_nacl() doing the same thing. This was manifesting as a general protection fault as reported by Justin: kernel: general protection fault: 0000 [#1] SMP kernel: Modules linked in: kernel: CPU: 0 PID: 11047 Comm: iscsi_ttx Not tainted 4.13.0-rc2.x86_64.1+ #20 kernel: Hardware name: Intel Corporation S5500BC/S5500BC, BIOS S5500.86B.01.00.0064.050520141428 05/05/2014 kernel: task: ffff88026939e800 task.stack: ffffc90007884000 kernel: RIP: 0010:target_put_nacl+0x49/0xb0 kernel: RSP: 0018:ffffc90007887d70 EFLAGS: 00010246 kernel: RAX: dead000000000200 RBX: ffff8802556ca000 RCX: 0000000000000000 kernel: RDX: dead000000000100 RSI: 0000000000000246 RDI: ffff8802556ce028 kernel: RBP: ffffc90007887d88 R08: 0000000000000001 R09: 0000000000000000 kernel: R10: ffffc90007887df8 R11: ffffea0009986900 R12: ffff8802556ce020 kernel: R13: ffff8802556ce028 R14: ffff8802556ce028 R15: ffffffff88d85540 kernel: FS: 0000000000000000(0000) GS:ffff88027fc00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00007fffe36f5f94 CR3: 0000000009209000 CR4: 00000000003406f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: Call Trace: kernel: transport_free_session+0x67/0x140 kernel: transport_deregister_session+0x7a/0xc0 kernel: iscsit_close_session+0x92/0x210 kernel: iscsit_close_connection+0x5f9/0x840 kernel: iscsit_take_action_for_connection_exit+0xfe/0x110 kernel: iscsi_target_tx_thread+0x140/0x1e0 kernel: ? wait_woken+0x90/0x90 kernel: kthread+0x124/0x160 kernel: ? iscsit_thread_get_cpumask+0x90/0x90 kernel: ? kthread_create_on_node+0x40/0x40 kernel: ret_from_fork+0x22/0x30 kernel: Code: 00 48 89 fb 4c 8b a7 48 01 00 00 74 68 4d 8d 6c 24 08 4c 89 ef e8 e8 28 43 00 48 8b 93 20 04 00 00 48 8b 83 28 04 00 00 4c 89 ef <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 20 kernel: RIP: target_put_nacl+0x49/0xb0 RSP: ffffc90007887d70 kernel: ---[ end trace f12821adbfd46fed ]--- To address this, go ahead and use proper list_del_list() for all cases of se_nacl->acl_list deletion. Reported-by:
Justin Maggard <jmaggard01@gmail.com> Tested-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 978d13d6 upstream. This patch fixes a bug associated with iscsit_reset_np_thread() that can occur during parallel configfs rmdir of a single iscsi_np used across multiple iscsi-target instances, that would result in hung task(s) similar to below where configfs rmdir process context was blocked indefinately waiting for iscsi_np->np_restart_comp to finish: [ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds. [ 6726.119440] Tainted: G W O 4.1.26-3321 #2 [ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000 [ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08 [ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0 [ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8 [ 6726.162667] Call Trace: [ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80 [ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290 [ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0 [ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100 [ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10 [ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod] [ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod] [ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod] [ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110 [ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0 [ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0 [ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71 It would happen because each iscsit_reset_np_thread() sets state to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting for completion on iscsi_np->np_restart_comp. However, if iscsi_np was active processing a login request and more than a single iscsit_reset_np_thread() caller to the same iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np kthread process context in __iscsi_target_login_thread() would flush pending signals and only perform a single completion of np->np_restart_comp before going back to sleep within transport specific iscsit_transport->iscsi_accept_np code. To address this bug, add a iscsi_np->np_reset_count and update __iscsi_target_login_thread() to keep completing np->np_restart_comp until ->np_reset_count has reached zero. Reported-by:
Gary Guo <ghg@datera.io> Tested-by:
-
Varun Prakash authored
commit ea8dc5b4 upstream. On receiving text request iscsi-target allocates buffer for payload in iscsit_handle_text_cmd() and assigns buffer pointer to cmd->text_in_ptr, this buffer is currently freed in iscsit_release_cmd(), if iscsi-target sets 'C' bit in text response then it will receive another text request from the initiator with ttt != 0xffffffff in this case iscsi-target will find cmd using itt and call iscsit_setup_text_cmd() which will set cmd->text_in_ptr to NULL without freeing previously allocated buffer. This patch fixes this issue by calling kfree(cmd->text_in_ptr) in iscsit_setup_text_cmd() before assigning NULL to it. For the first text request cmd->text_in_ptr is NULL as cmd is memset to 0 in iscsit_allocate_cmd(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Boris Brezillon authored
commit a11bf5ed upstream. Some ONFI NANDs do not support the SET/GET FEATURES commands, which, according to the spec, is perfectly valid. On these NANDs we can't set a specific timing mode using the "timing mode" feature, and we should assume the NAND does not require any setup to enter a specific timing mode. Signed-off-by:
Alexander Dahl <ada@thorsis.com> Tested-by:
-
Max Filippov authored
commit 7f81e55c upstream. csum_partial and csum_partial_copy_generic are defined unconditionally and are available even when CONFIG_NET is disabled. They are used not only by the network drivers, but also by scsi and media. Don't limit these functions export by CONFIG_NET. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit bc652eb6 upstream. Functions clear_user_highpage, copy_user_highpage, flush_dcache_page, local_flush_cache_range and local_flush_cache_page may be used from modules. Export them. Signed-off-by:
-
Max Filippov authored
commit 6d0f581d upstream. Currently building kernel for xtensa core with aliasing WT cache fails with the following messages: mm/memory.c:2152: undefined reference to `flush_dcache_page' mm/memory.c:2332: undefined reference to `local_flush_cache_page' mm/memory.c:1919: undefined reference to `local_flush_cache_range' mm/memory.c:4179: undefined reference to `copy_to_user_page' mm/memory.c:4183: undefined reference to `copy_from_user_page' This happens because implementation of these functions is only compiled when data cache is WB, which looks wrong: even when data cache doesn't need flushing it still needs invalidation. The functions like __flush_[invalidate_]dcache_* are correctly defined for both WB and WT caches (and even if they weren't that'd still be ok, just slower). Fix this by providing the same implementation of the above functions for both WB and WT cache. Signed-off-by:
-
Mel Gorman authored
commit 48fb6f4d upstream. Commit 65d8fc77 ("futex: Remove requirement for lock_page() in get_futex_key()") removed an unnecessary lock_page() with the side-effect that page->mapping needed to be treated very carefully. Two defensive warnings were added in case any assumption was missed and the first warning assumed a correct application would not alter a mapping backing a futex key. Since merging, it has not triggered for any unexpected case but Mark Rutland reported the following bug triggering due to the first warning. kernel BUG at kernel/futex.c:679! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 3695 Comm: syz-executor1 Not tainted 4.13.0-rc3-00020-g307fec773ba3 #3 Hardware name: linux,dummy-virt (DT) task: ffff80001e271780 task.stack: ffff000010908000 PC is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 LR is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 pc : [<ffff00000821ac14>] lr : [<ffff00000821ac14>] pstate: 80000145 The fact that it's a bug instead of a warning was due to an unrelated arm64 problem, but the warning itself triggered because the underlying mapping changed. This is an application issue but from a kernel perspective it's a recoverable situation and the warning is unnecessary so this patch removes the warning. The warning may potentially be triggered with the following test program from Mark although it may be necessary to adjust NR_FUTEX_THREADS to be a value smaller than the number of CPUs in the system. #include <linux/futex.h> #include <pthread.h> #include <stdio.h> #include <stdlib.h> #include <sys/mman.h> #include <sys/syscall.h> #include <sys/time.h> #include <unistd.h> #define NR_FUTEX_THREADS 16 pthread_t threads[NR_FUTEX_THREADS]; void *mem; #define MEM_PROT (PROT_READ | PROT_WRITE) #define MEM_SIZE 65536 static int futex_wrapper(int *uaddr, int op, int val, const struct timespec *timeout, int *uaddr2, int val3) { syscall(SYS_futex, uaddr, op, val, timeout, uaddr2, val3); } void *poll_futex(void *unused) { for (;;) { futex_wrapper(mem, FUTEX_CMP_REQUEUE_PI, 1, NULL, mem + 4, 1); } } int main(int argc, char *argv[]) { int i; mem = mmap(NULL, MEM_SIZE, MEM_PROT, MAP_SHARED | MAP_ANONYMOUS, -1, 0); printf("Mapping @ %p\n", mem); printf("Creating futex threads...\n"); for (i = 0; i < NR_FUTEX_THREADS; i++) pthread_create(&threads[i], NULL, poll_futex, NULL); printf("Flipping mapping...\n"); for (;;) { mmap(mem, MEM_SIZE, MEM_PROT, MAP_FIXED | MAP_SHARED | MAP_ANONYMOUS, -1, 0); } return 0; } Reported-and-tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Mel Gorman <mgorman@suse.de> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Cong Wang authored
commit d041353d upstream. We saw many list corruption warnings on shmem shrinklist: WARNING: CPU: 18 PID: 177 at lib/list_debug.c:59 __list_del_entry+0x9e/0xc0 list_del corruption. prev->next should be ffff9ae5694b82d8, but was ffff9ae5699ba960 Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 18 PID: 177 Comm: kswapd1 Not tainted 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_del_entry+0x9e/0xc0 shmem_unused_huge_shrink+0xfa/0x2e0 shmem_unused_huge_scan+0x20/0x30 super_cache_scan+0x193/0x1a0 shrink_slab.part.41+0x1e3/0x3f0 shrink_slab+0x29/0x30 shrink_node+0xf9/0x2f0 kswapd+0x2d8/0x6c0 kthread+0xd7/0xf0 ret_from_fork+0x22/0x30 WARNING: CPU: 23 PID: 639 at lib/list_debug.c:33 __list_add+0x89/0xb0 list_add corruption. prev->next should be next (ffff9ae5699ba960), but was ffff9ae5694b82d8. (prev=ffff9ae5694b82d8). Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 23 PID: 639 Comm: systemd-udevd Tainted: G W 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_add+0x89/0xb0 shmem_setattr+0x204/0x230 notify_change+0x2ef/0x440 do_truncate+0x5d/0x90 path_openat+0x331/0x1190 do_filp_open+0x7e/0xe0 do_sys_open+0x123/0x200 SyS_open+0x1e/0x20 do_syscall_64+0x61/0x170 entry_SYSCALL64_slow_path+0x25/0x25 The problem is that shmem_unused_huge_shrink() moves entries from the global sbinfo->shrinklist to its local lists and then releases the spinlock. However, a parallel shmem_setattr() could access one of these entries directly and add it back to the global shrinklist if it is removed, with the spinlock held. The logic itself looks solid since an entry could be either in a local list or the global list, otherwise it is removed from one of them by list_del_init(). So probably the race condition is that, one CPU is in the middle of INIT_LIST_HEAD() but the other CPU calls list_empty() which returns true too early then the following list_add_tail() sees a corrupted entry. list_empty_careful() is designed to fix this situation. [akpm@linux-foundation.org: add comments] Link: http://lkml.kernel.org/r/20170803054630.18775-1-xiyou.wangcong@gmail.com Fixes: 779750d2 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jonathan Toppins authored
commit 75dddef3 upstream. The RDMA subsystem can generate several thousand of these messages per second eventually leading to a kernel crash. Ratelimit these messages to prevent this crash. Doug said: "I've been carrying a version of this for several kernel versions. I don't remember when they started, but we have one (and only one) class of machines: Dell PE R730xd, that generate these errors. When it happens, without a rate limit, we get rcu timeouts and kernel oopses. With the rate limit, we just get a lot of annoying kernel messages but the machine continues on, recovers, and eventually the memory operations all succeed" And: "> Well... why are all these EBUSY's occurring? It sounds inefficient > (at least) but if it is expected, normal and unavoidable then > perhaps we should just remove that message altogether? I don't have an answer to that question. To be honest, I haven't looked real hard. We never had this at all, then it started out of the blue, but only on our Dell 730xd machines (and it hits all of them), but no other classes or brands of machines. And we have our 730xd machines loaded up with different brands and models of cards (for instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines meant it wasn't tied to any particular brand/model of RDMA hardware. To me, it always smelled of a hardware oddity specific to maybe the CPUs or mainboard chipsets in these machines, so given that I'm not an mm expert anyway, I never chased it down. A few other relevant details: it showed up somewhere around 4.8/4.9 or thereabouts. It never happened before, but the prinkt has been there since the 3.18 days, so possibly the test to trigger this message was changed, or something else in the allocator changed such that the situation started happening on these machines? And, like I said, it is specific to our 730xd machines (but they are all identical, so that could mean it's something like their specific ram configuration is causing the allocator to hit this on these machine but not on other machines in the cluster, I don't want to say it's necessarily the model of chipset or CPU, there are other bits of identicalness between these machines)" Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by:
Jonathan Toppins <jtoppins@redhat.com> Reviewed-by:
Doug Ledford <dledford@redhat.com> Tested-by:
-
- 13 Aug, 2017 9 commits
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
This reverts commit 1e9e7178 which is commit 661ccdc1 upstream. It's not needed in 4.9, and it breaks the build. Reported-by:
-
Suzuki K Poulose authored
commit 7e5a6722 upstream. The mmu_notifier_release() callback of KVM triggers cleaning up the stage2 page table on kvm-arm. However there could be other notifier callbacks in parallel with the mmu_notifier_release(), which could cause the call backs ending up in an empty stage2 page table. Make sure we check it for all the notifier callbacks. Fixes: commit 293f2936 ("kvm-arm: Unmap shadow pagetables properly") Reported-by:
Alex Graf <agraf@suse.de> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Rob Gardner authored
commit fc290a11 upstream. This fixes another cause of random segfaults and bus errors that may occur while running perf with the callgraph option. Critical sections beginning with spin_lock_irqsave() raise the interrupt level to PIL_NORMAL_MAX (14) and intentionally do not block performance counter interrupts, which arrive at PIL_NMI (15). But some sections of code are "super critical" with respect to perf because the perf_callchain_user() path accesses user space and may cause TLB activity as well as faults as it unwinds the user stack. One particular critical section occurs in switch_mm: spin_lock_irqsave(&mm->context.lock, flags); ... load_secondary_context(mm); tsb_context_switch(mm); ... spin_unlock_irqrestore(&mm->context.lock, flags); If a perf interrupt arrives in between load_secondary_context() and tsb_context_switch(), then perf_callchain_user() could execute with the context ID of one process, but with an active TSB for a different process. When the user stack is accessed, it is very likely to incur a TLB miss, since the h/w context ID has been changed. The TLB will then be reloaded with a translation from the TSB for one process, but using a context ID for another process. This exposes memory from one process to another, and since it is a mapping for stack memory, this usually causes the new process to crash quickly. This super critical section needs more protection than is provided by spin_lock_irqsave() since perf interrupts must not be allowed in. Since __tsb_context_switch already goes through the trouble of disabling interrupts completely, we fix this by moving the secondary context load down into this better protected region. Orabug: 25577560 Signed-off-by:
Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by:
Rob Gardner <rob.gardner@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 85f1bd9a ] When iteratively building a UDP datagram with MSG_MORE and that datagram exceeds MTU, consistently choose UFO or fragmentation. Once skb_is_gso, always apply ufo. Conversely, once a datagram is split across multiple skbs, do not consider ufo. Sendpage already maintains the first invariant, only add the second. IPv6 does not have a sendpage implementation to modify. A gso skb must have a partial checksum, do not follow sk_no_check_tx in udp_send_skb. Found by syzkaller. Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Greg Kroah-Hartman authored
revert "ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output" This reverts commit f102bb71 which is commit 0a28cfd5 upstream as there is another patch that needs to be applied instead of this one. Cc: Zheng Li <james.z.li@ericsson.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit ef09c9ff which is commit a5cb659b upstream as it causes merge issues with later patches that are much more important... Cc: Michal Kubecek <mkubecek@suse.cz> Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit c27927e3 ] Updates to tp_reserve can race with reads of the field in packet_set_ring. Avoid this by holding the socket lock during updates in setsockopt PACKET_RESERVE. This bug was discovered by syzkaller. Fixes: 8913336a ("packet: add PACKET_RESERVE sockopt") Reported-by:
-
Nikolay Borisov authored
[ Upstream commit 1714020e ] Commit dcd87999 ("igmp: net: Move igmp namespace init to correct file") moved the igmp sysctls initialization from tcp_sk_init to igmp_net_init. This function is only called as part of per-namespace initialization, only if CONFIG_IP_MULTICAST is defined, otherwise igmp_mc_init() call in ip_init is compiled out, casuing the igmp pernet ops to not be registerd and those sysctl being left initialized with 0. However, there are certain functions, such as ip_mc_join_group which are always compiled and make use of some of those sysctls. Let's do a partial revert of the aforementioned commit and move the sysctl initialization into inet_init_net, that way they will always have sane values. Fixes: dcd87999 ("igmp: net: Move igmp namespace init to correct file") Link: https://bugzilla.kernel.org/show_bug.cgi?id=196595Reported-by:
Gerardo Exequiel Pozzi <vmlinuz386@gmail.com> Signed-off-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
-
