- 24 Mar, 2016 40 commits
-
-
Dan Carpenter authored
commit 1d3cd177 upstream. We accidentally return IS_ERR(priv->base) which is 1 instead of PTR_ERR(priv->base) which is the error code. Fixes: 6c821bd9 ('net: Add MOXA ART SoCs ethernet driver') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Florian Westphal authored
commit 5d150a98 upstream. When ipv6_find_hdr is used to find a fragment header (caller specifies target NEXTHDR_FRAGMENT) we erronously return -ENOENT for all fragments with nonzero offset. Before commit 9195bb8e, when target was specified, we did not enter the exthdr walk loop as nexthdr == target so this used to work. Now we do (so we can skip empty route headers). When we then stumble upon a frag with nonzero frag_off we must return -ENOENT ("header not found") only if the caller did not specifically request NEXTHDR_FRAGMENT. This allows nfables exthdr expression to match ipv6 fragments, e.g. via nft add rule ip6 filter input frag frag-off gt 0 Fixes: 9195bb8e ("ipv6: improve ipv6_find_hdr() to skip empty routing headers") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Benjamin Poirier authored
commit 1837b2e2 upstream. The current reserved_tailroom calculation fails to take hlen and tlen into account. skb: [__hlen__|__data____________|__tlen___|__extra__] ^ ^ head skb_end_offset In this representation, hlen + data + tlen is the size passed to alloc_skb. "extra" is the extra space made available in __alloc_skb because of rounding up by kmalloc. We can reorder the representation like so: [__hlen__|__data____________|__extra__|__tlen___] ^ ^ head skb_end_offset The maximum space available for ip headers and payload without fragmentation is min(mtu, data + extra). Therefore, reserved_tailroom = data + extra + tlen - min(mtu, data + extra) = skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen) = skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen) Compare the second line to the current expression: reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset) and we can see that hlen and tlen are not taken into account. The min() in the third line can be expanded into: if mtu < skb_tailroom - tlen: reserved_tailroom = skb_tailroom - mtu else: reserved_tailroom = tlen Depending on hlen, tlen, mtu and the number of multicast address records, the current code may output skbs that have less tailroom than dev->needed_tailroom or it may output more skbs than needed because not all space available is used. Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs") Signed-off-by:
Benjamin Poirier <bpoirier@suse.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Jack Morgenstein authored
commit 6e522422 upstream. The VF administrative mac addresses (stored in the PF driver) are initialized to zero when the PF driver starts up. These addresses may be modified in the PF driver through ndo calls initiated by iproute2 or libvirt. While we allow the PF/host to change the VF admin mac address from zero to a valid unicast mac, we do not allow restoring the VF admin mac to zero. We currently only allow changing this mac to a different unicast mac. This leads to problems when libvirt scripts are used to deal with VF mac addresses, and libvirt attempts to revoke the mac so this host will not use it anymore. Fix this by allowing resetting a VF administrative MAC back to zero. Fixes: 8f7ba3ca ('net/mlx4: Add set VF mac address support') Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Reported-by:
Moshe Levi <moshele@mellanox.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 9bdfb3b7 upstream. Currently it's converted into msecs, thus HZ=1000 intact. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution") Signed-off-by:
-
Alex Deucher authored
commit d74e766e upstream. This reverts commit 39d42750. This caused a regression on some older hardware. bug: https://bugzilla.kernel.org/show_bug.cgi?id=113891Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Radim Krčmář authored
commit 7099e2e1 upstream. Linux guests on Haswell (and also SandyBridge and Broadwell, at least) would crash if you decided to run a host command that uses PEBS, like perf record -e 'cpu/mem-stores/pp' -a This happens because KVM is using VMX MSR switching to disable PEBS, but SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it isn't safe: When software needs to reconfigure PEBS facilities, it should allow a quiescent period between stopping the prior event counting and setting up a new PEBS event. The quiescent period is to allow any latent residual PEBS records to complete its capture at their previously specified buffer address (provided by IA32_DS_AREA). There might not be a quiescent period after the MSR switch, so a CPU ends up using host's MSR_IA32_DS_AREA to access an area in guest's memory. (Or MSR switching is just buggy on some models.) The guest can learn something about the host this way: If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results in #PF where we leak host's MSR_IA32_DS_AREA through CR2. After that, a malicious guest can map and configure memory where MSR_IA32_DS_AREA is pointing and can therefore get an output from host's tracing. This is not a critical leak as the host must initiate with PEBS tracing and I have not been able to get a record from more than one instruction before vmentry in vmx_vcpu_run() (that place has most registers already overwritten with guest's). We could disable PEBS just few instructions before vmentry, but disabling it earlier shouldn't affect host tracing too much. We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that optimization isn't worth its code, IMO. (If you are implementing PEBS for guests, be sure to handle the case where both host and guest enable PEBS, because this patch doesn't.) Fixes: 26a4f3c0 ("perf/x86: disable PEBS on a guest entry.") Reported-by:
Jiří Olša <jolsa@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Paul Mackerras authored
commit ccec4456 upstream. Thomas Huth discovered that a guest could cause a hard hang of a host CPU by setting the Instruction Authority Mask Register (IAMR) to a suitable value. It turns out that this is because when the code was added to context-switch the new special-purpose registers (SPRs) that were added in POWER8, we forgot to add code to ensure that they were restored to a sane value on guest exit. This adds code to set those registers where a bad value could compromise the execution of the host kernel to a suitable neutral value on guest exit. Fixes: b005255eReported-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Linus Torvalds authored
commit 256faedc upstream. This reverts commit dbb17a21. It turns out that commit can cause problems for systems with multiple GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid graphics. This got noticed originally in 4.4.4, where this patch had already gotten back-ported, but 4.5-rc7 was verified to have the same problem. Alexander Deucher says: "It looks like you have a muxed system so I suspect what's happening is that one of the display is being reported as connected for both the IGP and the dGPU and then the desktop environment gets confused or there some sort problem in the detect functions since the mux is not switched to the dGPU. I don't see an easy fix unless Dave has any ideas. I'd say just revert for now" Reported-by:
Jörg-Volker Peetz <jvpeetz@web.de> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 7f54ab5f upstream. This patch fixes a recent ABORT_TASK regression associated with commit febe562c, where a left-over target_put_sess_cmd() would still be called when __target_check_io_state() detected a command has already been completed, and explicit ABORT must be avoided. Note commit febe562c dropped the local kref_get_unless_zero() check in core_tmr_abort_task(), but did not drop this extra corresponding target_put_sess_cmd() in the failure path. So go ahead and drop this now bogus target_put_sess_cmd(), and avoid this potential use-after-free. Reported-by:
Dan Lane <dracodan@gmail.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Takashi Iwai authored
commit 15c66570 upstream. The firmware ctls like "DSP1 Firmware" in wm_adsp codec driver are enum, while the current driver accesses wrongly via value.integer.value[]. They have to be via value.enumerated.item[] instead. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Mark Brown <broonie@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Takashi Iwai authored
commit 8019c0b3 upstream. The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in wm8994 codec driver are enum ctls, while the current driver accesses wrongly via value.integer.value[]. They have to be via value.enumerated.item[] instead. Signed-off-by:
-
Takashi Iwai authored
commit d0784829 upstream. "MBC Mode", "VSS Mode", "VSS HPF Mode" and "Enhanced EQ Mode" ctls in wm8958 codec driver are enum, while the current driver accesses wrongly via value.integer.value[]. They have to be via value.enumerated.item[] instead. Signed-off-by:
-
Maximilain Schneider authored
commit e9a2d81b upstream. gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is allocated through alloc_candev() and should instead be freed using free_candev() alone. The inappropriate use of kfree() causes the kernel to hang when gs_destroy_candev() is called. Only the struct gs_usb * which is allocated through kzalloc() should be freed using kfree() when the device is disconnected. Signed-off-by:
Maximilian Schneider <max@schneidersoft.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Felix Fietkau authored
commit 7a36b930 upstream. The value 5000 was put here with the addition of the timeout field to ieee80211_start_tx_ba_session. It was originally added in mac80211 to save resources for drivers like iwlwifi, which only supports a limited number of concurrent aggregation sessions. Since iwlwifi does not use minstrel_ht and other drivers don't need this, 0 is a better default - especially since there have been recent reports of aggregation setup related issues reproduced with ath9k. This should improve stability without causing any adverse effects. Acked-by:
Avery Pennarun <apenwarr@gmail.com> Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Chris Bainbridge authored
commit f39ea269 upstream. Use kzalloc instead of kmalloc for struct tid_ampdu_rx to initialize the "removed" field (all others are initialized manually). That fixes: UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29 load of value 2 is not a valid value for type '_Bool' CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265 Workqueue: phy0 rt2x00usb_work_rxdone 0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007 ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500 ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032 Call Trace: [<ffffffff8181d866>] dump_stack+0x45/0x5f [<ffffffff8188422d>] ubsan_epilogue+0xd/0x40 [<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70 [<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730 [<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00 [<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750 [<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990 While at it, convert to use sizeof(*tid_agg_rx) instead. Fixes: 788211d8 ("mac80211: fix RX A-MPDU session reorder timer deletion") Signed-off-by:
Chris Bainbridge <chris.bainbridge@gmail.com> [reword commit message, use sizeof(*tid_agg_rx)] Signed-off-by:
-
Johannes Berg authored
commit cb150b9d upstream. Since cfg80211 frequently takes actions from its netdev notifier call, wireless extensions messages could still be ordered badly since the wext netdev notifier, since wext is built into the kernel, runs before the cfg80211 netdev notifier. For example, the following can happen: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether when setting the interface down causes the wext message. To also fix this, export the wireless_nlevent_flush() function and also call it from the cfg80211 notifier. Signed-off-by:
-
Johannes Berg authored
commit 8bf86273 upstream. Beniamino reported that he was getting an RTM_NEWLINK message for a given interface, after the RTM_DELLINK for it. It turns out that the message is a wireless extensions message, which was sent because the interface had been connected and disconnection while it was deleted caused a wext message. For its netlink messages, wext uses RTM_NEWLINK, but the message is without all the regular rtnetlink attributes, so "ip monitor link" prints just rudimentary information: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether (from my hwsim reproduction) This can cause userspace to get confused since it doesn't expect an RTM_NEWLINK message after RTM_DELLINK. The reason for this is that wext schedules a worker to send out the messages, and the scheduling delay can cause the messages to get out to userspace in different order. To fix this, have wext register a netdevice notifier and flush out any pending messages when netdevice state changes. This fixes any ordering whenever the original message wasn't sent by a notifier itself. Reported-by:
Beniamino Galvani <bgalvani@redhat.com> Signed-off-by:
-
Or Gerlitz authored
commit 11d8d645 upstream. According to IBTA spec v1.3 section 12.7.19, QPs should use GRH when the path returned by the SA has hop-limit > 0. Currently, we do that only for the > 1 case, fix that. Fixes: 6d969a47 ('IB/sa: Add ib_init_ah_from_path()') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Geert Uytterhoeven authored
commit b26a719b upstream. The R-Car GPIO driver handles Runtime PM for requested GPIOs only. When using a GPIO purely as an interrupt source, no Runtime PM handling is done, and the GPIO module's clock may not be enabled. To fix this: - Add .irq_request_resources() and .irq_release_resources() callbacks to handle Runtime PM when an interrupt is requested, - Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM when e.g. disabling/enabling an interrupt, or configuring the interrupt type. Fixes: d5c3d846 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS" Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - use gpio_to_priv() instead of gpiochip_get_data() - adjusted context ] Signed-off-by:
-
Richard Weinberger authored
commit e4f6daac upstream. ubi_start_leb_change() allocates too few bytes. ubi_more_leb_change_data() will write up to req->upd_bytes + ubi->min_io_size bytes. Signed-off-by:
Richard Weinberger <richard@nod.at> Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Maciej W. Rozycki authored
commit e723e3f7 upstream. Avoid sending a partially initialised `siginfo_t' structure along SIGFPE signals issued from `do_ov' and `do_trap_or_bp', leading to information leaking from the kernel stack. Signed-off-by:
Maciej W. Rozycki <macro@imgtec.com> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Simon South authored
commit 02322ac9 upstream. This patch applies the microphone-related fix created for the Acer Aspire E1-572 to the E1-472 as well, as it uses the same Realtek ALC282 CODEC and demonstrates the same issues. This patch allows an external, headset microphone to be used and limits the gain on the (quite noisy) internal microphone. Signed-off-by:
Simon South <simon@simonsouth.com> Signed-off-by:
-
Todd E Brandt authored
commit 92f9e179 upstream. Pause/unpause graph tracing around do_suspend_lowlevel as it has inconsistent call/return info after it jumps to the wakeup vector. The graph trace buffer will otherwise become misaligned and may eventually crash and hang on suspend. To reproduce the issue and test the fix: Run a function_graph trace over suspend/resume and set the graph function to suspend_devices_and_enter. This consistently hangs the system without this fix. Signed-off-by:
Todd Brandt <todd.e.brandt@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Alex Deucher authored
commit 5e031d9f upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Bjørn Mork authored
commit 04fdbc82 upstream. The MC74xx and EM74xx modules use different IDs by default, according to the Lenovo EM7455 driver for Windows. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Timothy Pearson authored
commit 2d02b8bd upstream. During DRAM initialization on certain ASpeed devices, an incorrect bit (bit 10) was checked in the "SDRAM Bus Width Status" register to determine DRAM width. Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05. Signed-off-by:
Timothy Pearson <tpearson@raptorengineeringinc.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Takashi Iwai authored
commit 197b958c upstream. The OSS sequencer client tries to drain the pending events at releasing. Unfortunately, as spotted by syzkaller fuzzer, this may lead to an unkillable process state when the event has been queued at the far future. Since the process being released can't be signaled any longer, it remains and waits for the echo-back event in that far future. Back to history, the draining feature was implemented at the time we misinterpreted POSIX definition for blocking file operation. Actually, such a behavior is superfluous at release, and we should just release the device as is instead of keeping it up forever. This patch just removes the draining call that may block the release for too long time unexpectedly. BugLink: http://lkml.kernel.org/r/CACT4Y+Y4kD-aBGj37rf-xBw9bH3GMU6P+MYg4W1e-s-paVD2pg@mail.gmail.comReported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Yegor Yefremov authored
commit c0992d0f upstream. Add support for Quectel UC20 and blacklist the QMI interface. Signed-off-by:
Yegor Yefremov <yegorslists@googlemail.com> [johan: amend commit message ] Signed-off-by:
-
Daniele Palmas authored
commit 5deef555 upstream. This patch adds support for 0x1045 PID of Telit LE922. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Vittorio Alfieri authored
commit 3c4c615d upstream. The Parrot NMEA GPS Flight Recorder is a USB composite device consisting of hub, flash storage, and cp210x usb to serial chip. It is an accessory to the mass-produced Parrot AR Drone 2. The device emits standard NMEA messages which make the it compatible with NMEA compatible software. It was tested using gpsd version 3.11-3 as an NMEA interpreter and using the official Parrot Flight Recorder. Signed-off-by:
Vittorio Alfieri <vittorio88@gmail.com> Signed-off-by:
-
Patrik Halfar authored
commit 013dd239 upstream. New revision of Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card has new idProduct. Bus 002 Device 006: ID 413c:81b3 Dell Computer Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x413c Dell Computer Corp. idProduct 0x81b3 bcdDevice 0.06 iManufacturer 1 Sierra Wireless, Incorporated iProduct 2 Dell Wireless 5809e Gobi
™ 4G HSPA+ Mobile Broadband Card iSerial 3 bNumConfigurations 2 Signed-off-by:Patrik Halfar <patrik_halfar@halfarit.cz> Signed-off-by:
-
Takashi Iwai authored
commit eab3c4db upstream. snd-hdsp driver accesses enum item values (int) instead of boolean values (long) wrongly for some ctl elements. This patch fixes them. Signed-off-by:
-
Takashi Iwai authored
commit c1099c32 upstream. HDSPM driver contains a code issuing zero-division potentially in system sample rate ctl code. This patch fixes it by not processing a zero or invalid rate value as a divisor, as well as excluding the invalid value to be passed via the given ctl element. Signed-off-by:
-
Takashi Iwai authored
commit 537e4813 upstream. snd-hdspm driver accesses enum item values (int) instead of boolean values (long) wrongly for some ctl elements. This patch fixes them. Signed-off-by:
-
Michael S. Tsirkin authored
commit 4cad67fc upstream. Calling return copy_to_user(...) in an ioctl will not do the right thing if there's a pagefault: copy_to_user returns the number of bytes not copied in this case. Fix up kvm to do return copy_to_user(...)) ? -EFAULT : 0; everywhere. Acked-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> [ luis: backported to 3.16: - dropped changes to arch/arm64/kvm/guest.c ] Signed-off-by:
-
Yadan Fan authored
commit 1ee9f4bd upstream. This issue is caused by commit 02323db1 ("cifs: fix cifs_uniqueid_to_ino_t not to ever return 0"), when BITS_PER_LONG is 64 on s390x, the corresponding cifs_uniqueid_to_ino_t() function will cast 64-bit fileid to 32-bit by using (ino_t)fileid, because ino_t (typdefed __kernel_ino_t) is int type. It's defined in arch/s390/include/uapi/asm/posix_types.h #ifndef __s390x__ typedef unsigned long __kernel_ino_t; ... #else /* __s390x__ */ typedef unsigned int __kernel_ino_t; So the #ifdef condition is wrong for s390x, we can just still use one cifs_uniqueid_to_ino_t() function with comparing sizeof(ino_t) and sizeof(u64) to choose the correct execution accordingly. Signed-off-by:
Yadan Fan <ydfan@suse.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Pavel Shilovsky authored
commit 6cc3b242 upstream. For interim responses we only need to parse a header and update a number credits. Now it is done for all SMB2+ command except SMB2_READ which is wrong. Fix this by adding such processing. Signed-off-by:
Pavel Shilovsky <pshilovsky@samba.org> Tested-by:
Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by:
-
Justin Maggard authored
commit deb7deff upstream. When opening a file, SMB2_open() attempts to parse the lease state from the SMB2 CREATE Response. However, the parsing code was not careful to ensure that the create contexts are not empty or invalid, which can lead to out- of-bounds memory access. This can be seen easily by trying to read a file from a OSX 10.11 SMB3 server. Here is sample crash output: BUG: unable to handle kernel paging request at ffff8800a1a77cc6 IP: [<ffffffff8828a734>] SMB2_open+0x804/0x960 PGD 8f77067 PUD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 3 PID: 2876 Comm: cp Not tainted 4.5.0-rc3.x86_64.1+ #14 Hardware name: NETGEAR ReadyNAS 314 /ReadyNAS 314 , BIOS 4.6.5 10/11/2012 task: ffff880073cdc080 ti: ffff88005b31c000 task.ti: ffff88005b31c000 RIP: 0010:[<ffffffff8828a734>] [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP: 0018:ffff88005b31fa08 EFLAGS: 00010282 RAX: 0000000000000015 RBX: 0000000000000000 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff88007eb8c8b0 RBP: ffff88005b31fad8 R08: 666666203d206363 R09: 6131613030383866 R10: 3030383866666666 R11: 00000000000002b0 R12: ffff8800660fd800 R13: ffff8800a1a77cc2 R14: 00000000424d53fe R15: ffff88005f5a28c0 FS: 00007f7c8a2897c0(0000) GS:ffff88007eb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffff8800a1a77cc6 CR3: 000000005b281000 CR4: 00000000000006e0 Stack: ffff88005b31fa70 ffffffff88278789 00000000000001d3 ffff88005f5a2a80 ffffffff00000003 ffff88005d029d00 ffff88006fde05a0 0000000000000000 ffff88005b31fc78 ffff88006fde0780 ffff88005b31fb2f 0000000100000fe0 Call Trace: [<ffffffff88278789>] ? cifsConvertToUTF16+0x159/0x2d0 [<ffffffff8828cf68>] smb2_open_file+0x98/0x210 [<ffffffff8811e80c>] ? __kmalloc+0x1c/0xe0 [<ffffffff882685f4>] cifs_open+0x2a4/0x720 [<ffffffff88122cef>] do_dentry_open+0x1ff/0x310 [<ffffffff88268350>] ? cifsFileInfo_get+0x30/0x30 [<ffffffff88123d92>] vfs_open+0x52/0x60 [<ffffffff88131dd0>] path_openat+0x170/0xf70 [<ffffffff88097d48>] ? remove_wait_queue+0x48/0x50 [<ffffffff88133a29>] do_filp_open+0x79/0xd0 [<ffffffff8813f2ca>] ? __alloc_fd+0x3a/0x170 [<ffffffff881240c4>] do_sys_open+0x114/0x1e0 [<ffffffff881241a9>] SyS_open+0x19/0x20 [<ffffffff8896e257>] entry_SYSCALL_64_fastpath+0x12/0x6a Code: 4d 8d 6c 07 04 31 c0 4c 89 ee e8 47 6f e5 ff 31 c9 41 89 ce 44 89 f1 48 c7 c7 28 b1 bd 88 31 c0 49 01 cd 4c 89 ee e8 2b 6f e5 ff <45> 0f b7 75 04 48 c7 c7 31 b1 bd 88 31 c0 4d 01 ee 4c 89 f6 e8 RIP [<ffffffff8828a734>] SMB2_open+0x804/0x960 RSP <ffff88005b31fa08> CR2: ffff8800a1a77cc6 ---[ end trace d9f69ba64feee469 ]--- Signed-off-by:
Justin Maggard <jmaggard@netgear.com> Signed-off-by:
-
Takashi Iwai authored
commit b24e7ad1 upstream. X32 ABI takes the 64bit timespec, thus the timer user status ioctl becomes incompatible with IA32. This results in NOTTY error when the ioctl is issued. Meanwhile, this struct in X32 is essentially identical with the one in X86-64, so we can just bypassing to the existing code for this specific compat ioctl. Signed-off-by:
-
