Currently a higher priority client can remove a lower priority
client's filter with equal match-expression.  This might happen if (a)
the higher priority client has a double-free bug, or (b) another
client with sufficient priority replaced and then removed an equal
filter, allowing the low priority client to insert an equal filter.

In neither case does it actually make sense to carry out the removal;
we should say the filter doesn't exist, as the filter currently
present is not the one that the high-priority client is referring to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Change all the 'stack' naming to 'auto' (or other meaningful term);
the device address list is based on more than just what the network
stack wants, and the no-match filters aren't really what the stack
wants at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

MAC filters inserted automatically by the driver, based on the device
address list (EF10) or no-match filters (Siena), should be overridable
at MANUAL or REQUIRED priority.  Currently they themselves have
REQUIRED priority and this requires some odd special-casing.

We also can't reliably tell whether such a MAC filter has or has
not been overridden.  We just remember that it is wanted by the
stack (RX_STACK flag).

Add another priority level, AUTO, between HINT and MANUAL, and
use this for the automatic filters while they have not been
overridden.  Remove the RX_STACK flag.  Add an RX_OVER_AUTO
flag which is set only when an AUTO filter has been overridden
(or was requested to be inserted while a higher-priority filter
existed).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The EF10 implementation already does this, and it makes more logical
sense to group the RSS hash key and indirection table together.
Rename the operation to rx_push_rss_config.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

In case of certain hardware and firmware errors it can be useful to
have more context than just the file and line number.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

A freshly allocated skb starts with timestamps clear.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The SFC9100 family has only one clock per controller, shared by all
functions.  Therefore only create a clock device under the primary
function, and make all other functions refer to the primary's clock
device.

Since PTP functionality is limited to port 0 and PF 0 on the earlier
SFN[56]322F boards, and we also set the primary flag for that
function, we can make the creation of a clock device conditional only
on this flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The primary function of an EF10 controller will share its clock
device with other functions in the same domain (which we call
secondary functions).  To this end, we need to associate functions
on the same controller.

We do not control probe order, so allow primary and secondary
functions to appear in any order.  Maintain global lists of all
primary functions and of unassociated secondary functions,
and a list of secondary functions on each primary function.

Use the VPD serial number to tell whether functions are part of the
same controller.  VPD will not be readable by virtual functions, so
this may need to be revisited later.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Original version by Stuart Hodgson.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The EF10 firmware can optionally insert RX timestamps in the packet
prefix.  These only include the clock minor value.  We must also
enable periodic time sync events on each event queue which provide
the high bits of the clock value.

[bwh: Combined and rebased several changes.
 Added the above description and some sanity checks for inline vs
 separate timestamps.
 Changed efx_rx_skb_attach_timestamp() to read the packet prefix
 from the skb head area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We can potentially pull the entire packet contents into the head area
and then free the page it was in.  In order to read an inline
timestamp safely, we need to copy the prefix into the head area as
well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

I added efx_ptp_get_mode() to avoid moving the definition for
efx_ptp_data, since the current PTP mode is needed for
siena.c:siena_set_ptp_hwtstamp.

[bwh: Also move the rx_filters mask, and add kernel-doc]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The clock minor tick on the SFC9100 family is 2^-27 s, not 1 ns.
There are also various pipeline delays which we need to correct for
when interpreting timestamps.

We query the firmware for the clock format and corrections at run-time.

[bwh: Combined and rebased several changes]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We'll be sharing clocks between multiple functions with their own MAC
addresses.  The name field is now documented as 'A short "friendly
name" to identify the clock ...' and '... not meant to be a unique
id.'  So use the name 'sfc'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We need a dedicated channel on Siena to ensure we can match up
the separate RX and timestamp events for each PTP packet.  We won't
do this for EF10 as timestamps are delivered inline.

Pass a channel index of 0 to MC_CMD_PTP_OP_ENABLE when there is no
dedicated channel.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The MC firmware will return error MC_CMD_ERR_ENOSPC if filter
insertion fails due to lack of resources.  The net driver's filter
implementation for Falcon-architecture returns EBUSY.  They should
behave consistently, so for EF10 change ENOSPC to EBUSY.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

efx_flush_all() is a really misleading name - it has nothing to do
with e.g. flushing DMA queues.  Since it's called immediately after
efx_stop_port() and is highly dependent on what that does, combine
the two functions.

Update comments to explain what this is doing a little better.
Also update an related and erroneous comment in efx_start_port().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Split each of efx_mcdi_rpc, efx_mcdi_rpc_finish, and efx_mcdi_rpc_async into
a normal and a _quiet version; made the former log MCDI errors with
netif_err (and include the raw MCDI error code), and the latter never log
them at all.  Changed various callers; any where some errors are expected
(but others are not) call the _quiet version and then if necessary log the
MCDI error themselves.  Said logging is done by new efx_mcdi_display_error.

Callers of efx_mcdi_rpc*_quiet functions which may want to log the error
need to ensure that their outbuf is big enough to hold an MCDI error; to
this end, they now use MCDI_DECLARE_BUF_OUT_OR_ERR, which always allocates
at least 8 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Add units to the "Sensor reports condition X for raw value Y" messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We don't directly control RX ingress on Siena or any later
controllers, and so we cannot prevent packets from entering the RX
datapath while the RX queues are not set up.  This results in
the hardware incrementing RX_NODESC_DROP_CNT, but it's not an
error and we should not include it in error stats.

When bringing an interface up or down, pull (or wait for) stats and
count the number of packets that were dropped while the interface was
down.  Subtract this from the reported RX dropped count.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The addition of RX event merging support means we don't reliably
detect dropped RX events now.  Currently we will only detect them if
the previous event for the RX queue had the CONT bit set.

Only accept RX completion events as merged if the
GET_CAPABILITIES_OUT_RX_BATCHING bit is set in datapath_caps (which it
won't be for the low-latency datapath) and the CONT bit is not set on
the event.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

To run BISTs the MC goes down in to a special mode where it will only
respond to MCDI from the testing PF, and TX, RX and event queues are
torn down. Other PFs get a message as it goes down to tell them it's
going down.

When the other PFs get this message, they check the soft status
register to tell when the MC has rebooted after BIST mode and they can
start recovery.

[bwh: Convert the test result to 1 or -1 as for earlier NICs]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The MC firmware is cooperatively multitasking and its scheduler will
send an event when a task yields after running for more than the
expected maximum time.  This can be useful for firmware development
but does not usually indicate a serious error and does not help to
detect a lockup (there is a hardware watchdog that does that).
Change the message and reduce log level accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Merge sfc fixes destined for 3.13, as development for 3.14+ depends on
some of them.

There is an as-yet unexplained bug that sometimes prevents (or delays)
the driver seeing the completion event for a completed MCDI request on
the SFC9120.  The requested configuration change will have happened
but the driver assumes it to have failed, and this can result in
further failures.  We can mitigate this by polling for completion
after unsuccessfully waiting for an event.

Fixes: 8127d661 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

rx_prefix_size is 4-bytes aligned on Falcon/Siena (16 bytes), but it is equal
to 14 on EF10. So, it should be taken into account if arch requires IP header
to be 4-bytes aligned (via NET_IP_ALIGN).

Fixes: 8127d661 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>