- 25 May, 2011 22 commits
-
-
Mike Frysinger authored
These boards don't have AD1980 modules, and that device is deprecated, so don't bother building it up by default anymore. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Since the value of these MMRs aren't changing, store the value in a local variable and work off of that. This avoids multiple MMR reads which are implicitly forced by the volatile markings. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
The BF537 SIC combines the gpio port H mask A interrupts with the emac rx interrupt, so we need to demux this in software. It also combines the gpio port H mask B and the emac tx interrupts, and the watchdog and port F mask B interrupts, but since we don't support mask B yet, just add the defines for now. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
The search logic in the gpio demux walks all possible gpio blocks starting at the specified pin. The trouble on bf537 parts when we demux the port F and port G mask A interrupts is that we also demux port H mask A ints. Most of the time this isn't an issue as people don't usually use port H, but might as well avoid it when possible. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
This functionality was merged into the common bfin_pm_standby_ctrl func some time ago, so punt these now unused funcs and data, and localize the wake funcs that aren't needed externally anymore. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
The SIC interrupt line muxing that the bf537 does is specific to this CPU (thankfully), so rip it out of the common code and move it to a bf537-specific file. This tidies up the common code significantly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
These are only used in a few internal Blackfin places, so move the irq prototypes out of the global header and into the internal irq one. No functional changes other than shuffling locales. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Prefer MMR named checks over part-specific lists, condense duplicated code across different #ifdef branches, simplify CONFIG_PM ifdefs, and drop unused kgdb header. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
These are in linux/ptrace.h, so no need for us to duplicate them. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Sonic Zhang authored
Make sure we mark cache flushing as unsafe to kgdb in SMP mode so that kgdb doesn't flush things incorrectly on us. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Not sure when we stopped using this field, but nothing in the tree uses this now, so punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
After some cache setup reordering changesets, the blackfin_cpudata init was left behind. While cpu0's data was correct, cpu1's data was not. Not that big of a deal as these are only used in the cpuinfo output, but should still be fixed. So move the setup of these fields to the common cache setup function to avoid this happening again in the future. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
The smp flush lines are too long and have too many newlines, so scale them back to match the other lines. The %p modifier shows "(null)" for 0, so use %08x instead. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Build the sound pieces that the board actually has into the kernel, and punt older devices that we discourage. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
This brings the parts in line with newer ones, and makes things easier to read at a glance. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
These files had a lot of whitespace damage, mostly due to copying and pasting original files that had damage. The BF561 header also had a lot of unused CONFIG_DEF_xxx defines, so punt them all. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Start a new common IRQ header and move all of the CEC pieces there. This lets the individual part headers worry just about its SIC defines. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Seems the ipipe code just copied & pasted the existing irq lookup logic, so pull the logic out of do_irq() and into a local helper, and convert the two users over to that. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
The local ivg structs need not be exported, so mark them as static. Further, the "num_spurious" variable is only incremented and never actually read anywhere, so punt it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Sonic Zhang authored
Since the on-chip L1 regions are not cacheable, there is no point in trying to flush/invalidate them. Plus, older Blackfin parts like to trigger an exception (like BF533-0.3). Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
Mike Frysinger authored
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
-
- 24 May, 2011 18 commits
-
-
git://git.fluff.org/bjdooks/linuxLinus Torvalds authored
* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits) mach-ux500: set proper I2C platform data from MOP500s i2c-nomadik: break out single messsage transmission i2c-nomadik: reset the hw after status check i2c-nomadik: remove the unnecessary delay i2c-nomadik: change the TX and RX threshold i2c-nomadik: add code to retry on timeout failure i2c-nomadik: use pm_runtime API i2c-nomadik: print abort cause only on abort tag i2c-nomadik: correct adapter timeout initialization i2c-nomadik: remove the redundant error message i2c-nomadik: corrrect returned error numbers i2c-nomadik: fix speed enumerator i2c-nomadik: make i2c timeout specific per i2c bus i2c-nomadik: add regulator support i2c: i2c-sh_mobile bus speed platform data V2 i2c: i2c-sh_mobile clock string removal i2c-eg20t: Support new device ML7223 IOH i2c: tegra: Add de-bounce cycles. i2c: tegra: fix repeated start handling i2c: tegra: recover from spurious interrupt storm ...
-
Ben Dooks authored
Merge branches 'for-2639/i2c-eg20t', 'for-2639/i2c-shmobile', 'for-2639/i2c-tegra' and 'for-2639/i2c-nomadik2' into for-linus/2640/i2c
-
Linus Walleij authored
This specifies the new per-platform timeout per I2C bus and switches the I2C buses to fast mode, and increase the FIFO depth to 8 for reads and writes. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Linus Walleij authored
Reduce code size in the message transfer function by factoring out a single-message transfer function. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
In case of I2C timeout, reset the HW only after the HW status is read, otherwise the staus will be lost. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
The delay in the driver seems to be not needed, so remove it. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Markus Grape <markus.grape@stericsson.com> Tested-by: Per Persson <per.xb.persson@stericsson.com> Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
1) Increase RX FIFO threshold so that there is a reduction in the number of interrupts handled to complete a transaction. 2) Fill TX FIFO in the write function. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
It is seen that i2c-nomadik controller randomly stops generating the interrupts leading to a i2c timeout. As a workaround to this problem, add retries to the on going transfer on failure. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Rabin Vincent authored
Use the pm_runtime API for pins control. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> [deleted some surplus runtime PM code] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
Modify the code to: 1)Print the cause of i2c failure only if the status is set to ABORT. 2)Print slave address on send/receive fail, will help in which slave failed. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
Correct the incorrect initialization of adapter timeout not to be in milliseconds, as it needs to be done in jiffies. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
srinidhi kasagar authored
The abort cause string itself is an error, so remove the redundant explicit error message. Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
The code was returning bad error numbers or just -1 in some cases. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Linus Walleij authored
The I2C speed enumerators in the i2c-nomadik header file were in the wrong order. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Virupax Sadashivpetimath authored
Add option to have different i2c timeout delay for different i2c buses specified in platform data. Default to the old value unless specified. Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
Jonas Aberg authored
This on-chip I2C controller needs to fetch the regulator representing its voltage domain so that it won't be switched off. Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/stagingLinus Torvalds authored
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: i2c-parport: Various cleanups i2c-i801: Don't depend on other kernel driver config options i2c-i801: Check for vendor Fujitsu before probing for apanel i2c-i801: Don't probe for slaves on IDF channels i2c-i801: SMBus patch for Intel Panther Point DeviceIDs i2c/writing-clients: Fix foo_driver.id_table
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6Linus Torvalds authored
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: jbd: Fix comment to match the code in journal_start() jbd/jbd2: remove obsolete summarise_journal_usage. jbd: Fix forever sleeping process in do_get_write_access() ext2: fix error msg when mounting fs with too-large blocksize jbd: fix fsync() tid wraparound bug ext3: Fix fs corruption when make_indexed_dir() fails ext3: Fix lock inversion in ext3_symlink()
-