This reverts commit 858d5881.

Joachim reports that this commit breaks lpc18xx boot. This is
because the hardware has circular clk topology where PLLs can
feed into dividers and the same dividers can feed into the PLLs.
The hardware is designed this way so that you can choose to put
the divider before the PLL or after the PLL depending on what you
configure to be the parent of the divider and what you configure
to be the parent of the PLL.

So let's drop this patch for now because we have hardware that
actually has loops. A future patch could check for circular
parents when we change parents and fail the switch, but that's
probably best left to some debugging Kconfig option so that we
don't suffer the sanity checking cost all the time.
Reported-by: Joachim Eastwood <manabian@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

There are some Arria10 clocks of type "altr,socfpga-a10-perip-clk" that can
have multiple parents. Fix up the __socfpga_periph_init() to call
of_clk_parent_fill() that will return the appropriate number of parents.

Also, update __socfpga_gate_init() to call of_clk_parent_fill() helper
function.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Convert DPLL support code to use clk_hw pointers for reference and bypass
clocks. This allows us to use clk_hw_* APIs for accessing any required
parameters for these clocks, avoiding some locking problems at least with
DPLL enable code; this used clk_get_rate which uses mutex but isn't
good under clk_enable / clk_disable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

* clk-fixes:
  clk: ti: omap3+: dpll: use non-locking version of clk_get_rate

This patch corrects the enable register offset which is actually 0x36cc
instead of 0x36c4
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 5f775498 ("clk: qcom: Fully support apq8064 global clock control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.

This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Currently the Exynos5433 (ARMv8 SoC) clock driver depends on ARCH_EXYNOS
so it is built also on ARMv7. This does not bring any kind of benefit.
There won't be a single kernel image for ARMv7 and ARMv8 SoCs (like
multi_v7 for ARMv7).

Instead build clock drivers only for respective SoC's architecture.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Merge branch 'clk-shmobile-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

* clk-fixes:
  clk: gpio: Really allow an optional clock= DT property
  Revert "clk: qcom: Specify LE device endianness"

We mis-merged the original patch from Russell here and so the
patch went almost all the way, except that we still failed to
probe when there wasn't a clocks property in the DT node. Allow
that case by making a negative value from
of_clk_get_parent_count() into "no parents", like the original
patch did.

Fixes: 7ed88aa2 ("clk: fix clk-gpio.c with optional clock= DT property")
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add the "intc-ex" clock to the r8a7795 CPG MSSR driver.

According to information from the hardware team the INTC-EX
parent clock is CP. The next data sheet version will include
this information.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Export symbol of_clk_get_from_provider so it can be used in
loadable kernel modules
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Enable the COMPILE_TEST to get build coverage of some of Samsung clock
controller drivers. Still some of them will be built only if
appropriate SoC is chosen (like SOC_EXYNOS4415 or ARCH_S3C64XX).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

We were rolling this ourselves, but clk-divider can do it now.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Our dividers weren't being set successfully because CM_PASSWORD wasn't
included in the register write.  It looks easier to just compute the
divider to write ourselves than to update clk-divider for the ability
to OR in some arbitrary bits on write.

Fixes about half of the video modes on my HDMI monitor (everything
except 720x400).

Cc: stable@vger.kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Cfr. commit a9ec81f4 ("serial: sh-sci: Drop the interface
clock").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>

Merge tag 'v4.6-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next

Introduction of a factor type and a variant containing a gate
to be able to also declare factor clocks in their correct
place in the clock tree instead of having to register factor
clocks in the init callback separately. And as always some more
clock-ids and non-regression fixes for mistakes introduced in
past kernel releases.

This reverts commit 329cabce.

The commit that caused us to specify LE device endianness here,
29bb45f2 (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.

Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

With gdsc driver capable of handling hierarchical power domains,
specify oxili_gdsc as parent of oxilicx_gdsc.

Remove all direct calls to genpd from the mmcc clock driver. The
adding and removing of subdomains is now handled from within
the gdsc driver.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add all gdsc data which are part of mmcc on msm8996 family
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add all data for the GDSCs which are part of msm8996 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Some gdscs might be controlled via voting registers and might not
really disable when the kernel intends to disable them (due to other
votes keeping them enabled)
Mark these gdscs with a flag for we do not check/wait on a disable
status for these gdscs within the kernel disable callback.

Also at boot, if these GDSCs are found to be ON, we make sure we
vote for them before we inform the genpd framework about their
status. If genpd gets no users, it then disables (removes the vote)
them as part of genpd_poweroff_unused()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Some gdsc power domains can have a gds_hw_controller block inside
to help ensure all slave devices within the power domain are idle
before the gdsc is actually switched off.
This is mainly useful in power domains which host a MMU, in which
case its necessary to make sure there are no outstanding MMU operations
or pending bus transactions before the power domain is turned off.

In gdscs with gds_hw_controller block, its necessary to check the
gds_hw_ctrl status bits instead of the ones in gdscr, to determine
the state of the powerdomain.

While at it, also move away from using jiffies and use ktime APIs
instead for busy looping on status bits.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Some qcom SoCs' can have hierarchical power domains. Let the gdsc structs
specify the parents (if any) and the driver add genpd subdomains for them.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This patch add the support to setup the HCLK PLL output
using the "assigned-clock-rates" parameter in the device tree.

If the option is not use, the clock setup by the kickstart
and/or bootloader remain unchanged.

The previous kernel version did not change the clock frequency
output setup by the kickstart and/or bootloader;
this version always setup the clock frequency output to 208MHz.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

* clk-fixes:
  clk: versatile: mask VCO bits before writing

The Versatile syscon ICST driver OR:s the bits into place but
forgets to mask the previous value, making the code only work
if the register is zero or giving haphazard results. Mask the
19 bits used by the Versatile syscon interface register.

Regression caused and now fixed by yours truly.

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Fixes: 179c8fb3 ("clk: versatile-icst: convert to use regmap")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The following errors are display in the console during the power-on:
[    0.000000] lpc32xx_usb_clk_init: failed to register (null) clock: -12
[    0.000000] lpc32xx_clk_init: failed to register (null) clock: -12

There is no need to register clock "0"; the first clock used is 1;
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
[sboyd@codeaurora.org: s/prepare/register/]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Before commit b3d192d5121f ("clk: simplify __clk_init_parent()"),
__clk_init_parent() called .get_parent() only for multi-parent
clocks.  That commit changed the behavior to call .get_parent()
if available even for single-parent clocks and root clocks.

It turned out a problem because there are some single-parent clocks
that implement .get_parent() callback and return non-zero index.
The SOCFPGA clock is the case; the commit broke the SOCFPGA boards.

To keep the original behavior, invoke .get_parent() only when
num_parents is greater than 1.

Fixes: b3d192d5121f ("clk: simplify __clk_init_parent()")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

We were not checking the return from devm_add_action() which can fail.
Start using the helper and devm_add_action_or_reset() and return
directly as we know that the cleanup has been done by this helper.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add a helper function devm_add_action_or_reset() which will internally
call devm_add_action(). But if devm_add_action() fails then it will
execute the action mentioned and return the error code.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

As preparation for arm64 based mesongxbb, which pulls in this code once
enabling ARCH_MESON, fix a size_t vs. unsigned int type mismatch.
The loop uses a local unsigned int variable, so adopt that type,
matching the header.

Fixes: 7a29a869 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

clang found a bug with the __socfpga_pll_init definition:

drivers/clk/socfpga/clk-pll-a10.c:77:15: error: '__section__' attribute only applies to functions and
      global variables

This moves the __init annotation to the right place so the function
actually gets discarded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

There are two TI CDCE clock chips in this file. Move them close
together so they're easier to find.

No functional change, just cosmetic.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Alphabetize]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Simple cosmetic fix.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

* clk-fixes:
  clk: tegra: super: Fix sparse warnings for functions not declared as static
  clk: tegra: Fix sparse warnings for functions not declared as static
  clk: tegra: Fix sparse warning for pll_m
  clk: tegra: Use definition for pll_u override bit
  clk: tegra: Fix warning caused by pll_u failing to lock
  clk: tegra: Fix clock sources for Tegra210 EMC
  clk: tegra: Add the APB2APE audio clock on Tegra210
  clk: tegra: Add missing of_node_put()
  clk: tegra: Fix PLLE SS coefficients
  clk: tegra: Fix typos around clearing PLLE bits during enable
  clk: tegra: Do not disable PLLE when under hardware control
  clk: tegra: Fix pllx dyn step calculation
  clk: tegra: pll: Fix potential sleeping-while-atomic
  clk: tegra: Fix the misnaming of nvenc from msenc
  clk: tegra: Fix naming of MISC registers
  clk: tegra: Remove improper flags for lock_enable
  clk: tegra: Fix divider on VI_I2C

Merge tag 'tegra-for-4.5-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-fixes

Pull tegra fixes from Thierry Reding:

clk: tegra: Fixes for v4.5-rc3

This set contains a bunch of miscellaneous fixes that have accumulated
over the past couple of weeks, primarily for the Tegra210 support added
in v4.5-rc1.

* tag 'tegra-for-4.5-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  clk: tegra: super: Fix sparse warnings for functions not declared as static
  clk: tegra: Fix sparse warnings for functions not declared as static
  clk: tegra: Fix sparse warning for pll_m
  clk: tegra: Use definition for pll_u override bit
  clk: tegra: Fix warning caused by pll_u failing to lock
  clk: tegra: Fix clock sources for Tegra210 EMC
  clk: tegra: Add the APB2APE audio clock on Tegra210
  clk: tegra: Add missing of_node_put()
  clk: tegra: Fix PLLE SS coefficients
  clk: tegra: Fix typos around clearing PLLE bits during enable
  clk: tegra: Do not disable PLLE when under hardware control
  clk: tegra: Fix pllx dyn step calculation
  clk: tegra: pll: Fix potential sleeping-while-atomic
  clk: tegra: Fix the misnaming of nvenc from msenc
  clk: tegra: Fix naming of MISC registers
  clk: tegra: Remove improper flags for lock_enable
  clk: tegra: Fix divider on VI_I2C

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>