When the 82575 is fed 802.1q packets, it chokes with
an error of the form:

igb 0000:08:00.1 partial checksum but proto=81!

As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.

There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.

Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution.  This patch is
based upon his work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hi,

IBM EMAC driver performs device reset (drivers/net/ibm_newemac/core.c:
emac_probe() -> emac_init_phy() -> emac_reset()) before registering
appropriate net_device (emac_probe() -> register_netdev()), so
net_device name contains raw format string during EMAC reset ("eth%d").

If the case of reset timeout, emac_report_timeout_error() function is
called to report an error. The problem is this function uses net_device
name to report device related, which is not correct, as a result in the
kernel log buffer we see:

eth%d: reset timeout

The solution is to print device_node full_name instead. After applying
the patch proposed, error string is like the following:

/plb/opb/ethernet@ef600e00: reset timeout
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no gain using prefetch() in dev_hard_start_xmit(), since
we already had to read ops->ndo_select_queue pointer in dev_pick_tx(),
and both pointers are probably located in the same cache line.

This prefetch call slows down fast path because of a stall in address
computation.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove 2 TEST_FRAME hacks that are no longer needed.  These allowed
sctp regression tests to compile before, but are no longer needed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some minor changes to queue hashing:
 1. Use const on accessor functions
 2. Export skb_tx_hash for use in drivers (see ixgbe)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than calling device pointer directly (which is incorrect with
net_device_ops), use the standard dev_change_mtu. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_sack_swap seems unnecessary so I pushed swap to the caller.
Also removed comment that seemed then pointless, and added include
when not already there. Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

A zero length frame filter was recently introduced in ROSE protocole.
Previous commit makes the same at AX25 protocole level.
This patch has the same purpose for NetRom  protocole.
The reason is that empty frames have no meaning in NetRom protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous commit 244f46ae
was introduced a zero length frame filter for ROSE protocole.
This patch has the same purpose at AX25 frame level for the same
reason. Empty frames have no meaning in AX25 protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch condenses two debug messages in one.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 1577ecef ("netdev: Merge UCC
and gianfar MDIO bus drivers") broke the TSEC TBI PHY support: the
driver now refuses to probe TBI MDIO buses as it doesn't know about
"fsl,gianfar-tbi" compatible entry, and thus _probe() fails with
-ENODEV status.

Fix this by adding "fsl,gianfar-tbi" to the list of known Gianfar
MDIO buses.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

reorder struct inet6_ifaddr to remove padding on 64 bit builds
    
remove 8 bytes of padding so inet6_ifaddr becomes 192 bytes & fits into
a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 4826857f ("gianfar: pass the
proper dev to DMA ops") introduced this build breakage:

  CC      drivers/net/gianfar.o
drivers/net/gianfar.c: In function 'gfar_suspend':
drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev'
drivers/net/gianfar.c: In function 'gfar_resume':
drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev'
make[2]: *** [drivers/net/gianfar.o] Error 1

Fix this by converting suspend and resume routines to use
gfar_private->ndev.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables support for the new Intel 82552 adapter (new PHY paired
with the existing MAC in the ICH7 chipset).  No new features are added to
the driver, however there are minor changes due to updated registers and a
few workarounds for hardware errata.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When merging into Jeff's tree:

	commit 5f66f208
	Author: Arthur Jones <ajones@riverbed.com>
	Date:   Thu Mar 19 01:13:08 2009 +0000

	    e1000e: allow tx of pre-formatted vlan tagged packets

We lost one line, this fixes that missing
piece...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/virtio_net.c

dev_queue_xmit() needs to dirty fields "state", "q", "bstats" and "qstats"

On x86_64 arch, they currently span three cache lines, involving more
cache line ping pongs than necessary, making longer holding of queue spinlock.

We can reduce this to one cache line, by grouping all read-mostly fields
at the beginning of structure. (Or should I say, all highly modified fields
at the end :) )

Before patch :

offsetof(struct Qdisc, state)=0x38
offsetof(struct Qdisc, q)=0x48
offsetof(struct Qdisc, bstats)=0x80
offsetof(struct Qdisc, qstats)=0x90
sizeof(struct Qdisc)=0xc8

After patch :

offsetof(struct Qdisc, state)=0x80
offsetof(struct Qdisc, q)=0x88
offsetof(struct Qdisc, bstats)=0xa0
offsetof(struct Qdisc, qstats)=0xac
sizeof(struct Qdisc)=0xc0
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed duplicated #include in drivers/net/dnet.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load.  On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598).  These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This code updates ixgb so that it can use the skb_dma_map/unmap functions
to map the buffers.  In addition it also updates the tx hang logic to use
time_stamp instead of dma to determine if it has detected a tx hang.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As with igb, when the e1000e driver is fed 802.1q
packets with hardware checksum on, it chokes with an
error of the form:

checksum_partial proto=81!

As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.

There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out wiht the correct hardware checksum.

Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution.  This patch is
based upon his work.

Fixups from Stephen Hemminger <shemminger@vyatta.com> and
Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were a few issues I noticed in e1000e. These include a double free
of the skb if mapping fails, and the fact that context descriptors appear
to be left in the descriptor ring after the failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device ID and related support for 82583 mac.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Radheka Godse <radheka.godse@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cpu_to_le16 here looks suspicious to me, I don't think we need it
because put_unaligned_le16 also does this.

I don't currently have any big endian hardware with a PCI bus available
to test on, so I haven't been able to verify this.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces the generic eth_mac_addr function with one that
also updates the hardware mac address registers.  It also renames the
existing smsc911x_set_mac_address function to
smsc911x_hw_set_mac_address for clarity.

Newer LAN911x and all LAN921x devices also support changing the mac
address while the device is running, which is useful for some bonding
modes.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vast majority of bit constants in this driver are defined in the
header file, but TX and RX status word bits are not.  This patch (which
should make no functional change) defines these, to make the driver
slightly more readable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To improve manageability, it would be good to be able to disambiguate routes
added by administrator from those added by DHCP client.  The only necessary
kernel change is to add value to rtnetlink include file so iproute2 utility
can use it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every USB transfer buffer has to be allocated individually by kmalloc.

Impact: bugfix, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Kolja Waschk <kawk@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier.  This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.

Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up.  On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.

The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode.  When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.

Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval.  An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was
changed.
This revises it for this change.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to be passing the of_platform device struct into the DMA ops as
its the one that has the archdata setup to know which low-level DMA ops we
should be using (not the net_device one).  This isn't an issue until we
expect the archdata to be setup correctly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev can be NULL in ip[6]_frag_reasm for skb's coming from RAW sockets.

Quagga's OSPFD sends fragmented packets on a RAW socket, when netfilter
conntrack reassembles them on the OUTPUT path you hit this code path.

You can test it with something like "hping2 -0 -d 2000 -f AA.BB.CC.DD"

With help from Jarek Poplawski.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>