This fixes the following compiler warnings when compiling the
reuseport_bpf testcase on a 32 bit platform:

reuseport_bpf.c: In function ‘attach_ebpf’:
reuseport_bpf.c:114:15: warning: cast from pointer to integer of ifferent size [-Wpointer-to-int-cast]
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since implementing VLAN filtering in commit 05cc5a39
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:

  # ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
  RTNETLINK answers: Bad address

and in dmesg (with bnx2x.debug=0x20):
  bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
  configuration the interface is down

Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
 - Accept requests to add/kill VID regardless of the device state.
   Maintain the requested list of VIDs in the bp->vlan_reg list.
 - If the device is up, try to configure the VID list into the hardware.
   If we run out of VLAN credits or encounter a failure configuring an
   entry, fall back to accepting all VLANs.
   If we successfully configure all entries from the list, turn the
   fallback off.
 - Use the same code for reconfiguring VLANs during NIC load.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.7

brcmfmac

* add fallback RSSI report for devices that do not report per-chain values
* fix a null pointer derefence regression on PCIe full dongle devices

rtlwifi

* fix scheduling while atomic regression from commit 49f86ec2

MAINTAINERS

* add file patterns for wireless device tree bindings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

John Crispin says:

====================
net-next: mediatek: improve phy support

The current driver did not handle the RGMII delay modes and asymmetric flow
control properly. The mii_bus is not freed properly. Also add support for
fixed-phy allowing the driver to work on SoCs that have an internal gigabit
switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If an external Gigabit PHY is connected to either of the MACs we need to
be able to tell the PHY to use a delay. Not doing so will result in heavy
packet loss and/or data corruption when using PHYs such as the IC+ IP1001.
We tell the PHY which MII delay mode to use via the devictree.

The ethernet driver needs to be adapted to handle all 3 rgmii-*id modes
in the same way as normal rgmii when setting up the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MT7623 SoC has a builtin gigabit switch. If we want to use it, GMAC1
needs to be configured using a fixed link speed and flow control settings.
The easiest way to do this is to used the fixed-phy driver, allowing us to
reuse the existing mdio polling code to setup the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code will not setup the PHYs advertisement features correctly.
Fix this and properly advertise Gigabit features and properly handle
asymmetric pause frames.
Signed-off-by: Sean Wang <keyhaede@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently uses kfree() to clear the mii_bus. This is not the
correct way to clear the memory and mdiobus_free() should be used instead.
This patch fixes the two instances where this happens in the driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx-usecs shouldn't be changed while interface down/up.
Currently, for instance, if it's set to 100us, after interface
down/up it's 500us. It's a hidden bug that can lead to lavish
interrupt pacing time increasing while "down/up" up to max value.

Steps to reproduce:
- set rx-usecs to be 100us
- down/up interface
- read new unexpected rx-usecs
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the transmit hardware timestamping is enabled, an additional
TxBD would be added and would be set as the last TxBD with TXBD_LAST
and TXBD_INTERRUPT. However this has been broken by a patch recently.
This made the software couldn't get transmit hardware timestamps and
resulted in call trace. So, this patch is to fix this issue.

Fixes: 48963b44 ("gianfar: Remove redundant ops for do_tstamp
       from xmit()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to update backlog too when we update qlen.

Joint work with Stas.
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Tested-by: Stas Nichiporovich <stasn77@gmail.com>
Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hfsc updates backlog lazily, that is only when we
dump the stats. This is problematic after we begin to
update backlog in qdisc_tree_reduce_backlog().
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Tested-by: Stas Nichiporovich <stasn77@gmail.com>
Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A regression was introduced in commit 9c349892 ("brcmfmac: revise
handling events in receive path") which moves eth_type_trans() call
to brcmf_rx_frame(). Msgbuf layer doesn't use brcmf_rx_frame() but invokes
brcmf_netif_rx() directly. In such case the Ethernet header was not
stripped out resulting in null pointer dereference in the networking
stack.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffff814c3ce6>] enqueue_to_backlog+0x56/0x260
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: fuse ipt_MASQUERADE nf_nat_masquerade_ipv4
iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 xt_addrtype
[...]
rtsx_pci scsi_mod usbcore usb_common i8042 serio nvme nvme_core
CPU: 7 PID: 1340 Comm: irq/136-brcmf_p Not tainted 4.7.0-rc1-mainline #1
Hardware name: Dell Inc. XPS 15 9550/0N7TVV, BIOS 01.02.00 04/07/2016
task: ffff8804a0c5bd00 ti: ffff88049e124000 task.ti: ffff88049e124000
RIP: 0010:[<ffffffff814c3ce6>] [<ffffffff814c3ce6>]
enqueue_to_backlog+0x56/0x260
RSP: 0018:ffff88049e127ca0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8804bddd7c40 RCX: 000000000000002f
RDX: 0000000000000000 RSI: 0000000000000007 RDI: ffff8804bddd7d4c
RBP: ffff88049e127ce8 R08: 0000000000000000 R09: 0000000000000000
R10: ffff8804bddd12c0 R11: 000000000000149e R12: 0000000000017c40
R13: ffff88049e127d08 R14: ffff8804a9bd6d00 R15: ffff8804bddd7d4c
FS: 0000000000000000(0000) GS:ffff8804bddc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000048 CR3: 0000000001806000 CR4: 00000000003406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff8804bdddad00 ffff8804ad089e00 0000000000000000 0000000000000282
0000000000000000 ffff8804a9bd6d00 ffff8804a1b27e00 ffff8804a9bd6d00
ffff88002ee88000 ffff88049e127d28 ffffffff814c3f3b ffffffff81311fc3
Call Trace:
[<ffffffff814c3f3b>] netif_rx_internal+0x4b/0x170
[<ffffffff81311fc3>] ? swiotlb_tbl_unmap_single+0xf3/0x120
[<ffffffff814c5467>] netif_rx_ni+0x27/0xc0
[<ffffffffa08519e9>] brcmf_netif_rx+0x49/0x70 [brcmfmac]
[<ffffffffa08564d4>] brcmf_msgbuf_process_rx+0x2b4/0x570 [brcmfmac]
[<ffffffff81020017>] ? __xen_set_pgd_hyper+0x57/0xd0
[<ffffffff810d60b0>] ? irq_forced_thread_fn+0x70/0x70
[<ffffffffa0857381>] brcmf_proto_msgbuf_rx_trigger+0x31/0xe0 [brcmfmac]
[<ffffffffa0861e8f>] brcmf_pcie_isr_thread+0x7f/0x110 [brcmfmac]
[<ffffffff810d60d0>] irq_thread_fn+0x20/0x50
[<ffffffff810d63ad>] irq_thread+0x12d/0x1c0
[<ffffffff815d07d5>] ? __schedule+0x2f5/0x7a0
[<ffffffff810d61d0>] ? wake_threads_waitq+0x30/0x30
[<ffffffff810d6280>] ? irq_thread_dtor+0xb0/0xb0
[<ffffffff81098ea8>] kthread+0xd8/0xf0
[<ffffffff815d4b7f>] ret_from_fork+0x1f/0x40
[<ffffffff81098dd0>] ? kthread_worker_fn+0x170/0x170
Code: 1c f5 60 9a 8e 81 9c 58 0f 1f 44 00 00 48 89 45 d0 fa 66 0f 1f
44 00 00 4c 8d bb 0c 01 00 00 4c 89 ff e8 5e 08 11 00 49 8b 56 20 <48>
8b 52 48 83 e2 01 74 10 8b 8b 08 01 00 00 8b 15 59 c5 42 00
RIP [<ffffffff814c3ce6>] enqueue_to_backlog+0x56/0x260
RSP <ffff88049e127ca0>
CR2: 0000000000000048

Fixes: 9c349892 ("brcmfmac: revise handling events in receive path")
Reported-by: Rafal Milecki <zajec5@gmail.com>
Reported-by: Grey Christoforo <grey@christoforo.net>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
[arend@broadcom.com: rephrased the commit message]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The last field "flags" of object "minfo" is not initialized.
Copying this object out may leak kernel stack data.
Assign 0 to it to avoid leak.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

link_info.str is a char array of size 60. Memory after the NULL
byte is not initialized. Sending the whole object out can cause
a leak.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.

The intent was to avoid udp_lib_checksum_complete() overhead.

But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.

Fixes: e6afc8ac ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac_mdio_reset() has been updated to use msleep rather udelay
(as some PHY requires a one second delay there).
It called from stmmac_resume() within the spin_lock_irqsave block
atomic context triggering 'scheduling while atomic'.

The stmmac_priv lock usage is not fully documented, but it seems
to protect the access to the MAC registers / DMA structures rather
than the MDIO bus or the PHY (which have separate locking),
so we can push the spin_lock after the stmmac_mdio_reset call.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc warns about qed_fill_link possibly accessing uninitialized data:

drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]

While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.

This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.

The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.

As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

priv is assigned to NULL however some of the early error exit paths to
label 'free' dereference priv, causing a null pointer dereference.

Move the label 'free' to just the free_netdev statement, and add a new
exit path 'free2' for the error cases were clk_disable_unprepare needs
calling before the final free.

Fixes issue found by CoverityScan, CID#113260
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Fix incorrect timestamp in nfnetlink_queue introduced when addressing
   y2038 safe timestamp, from Florian Westphal.

2) Get rid of leftover conntrack definition from the previous merge
   window, oneliner from Florian.

3) Make nf_queue handler pernet to resolve race on dereferencing the
   hook state structure with netns removal, from Eric Biederman.

4) Ensure clean exit on unregistered helper ports, from Taehee Yoo.

5) Restore FLOWI_FLAG_KNOWN_NH in nf_dup_ipv6. This got lost while
   generalizing xt_TEE to add packet duplication support in nf_tables,
   from Paolo Abeni.

6) Insufficient netlink NFTA_SET_TABLE attribute check in
   nf_tables_getset(), from Phil Turnbull.

7) Reject helper registration on duplicated ports via modparams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three small fixes for the current cycle:
 * missing netlink attribute check in hwsim wmediumd (Martin)
 * fast xmit structure alignment fix (Felix)
 * mesh path flush/synchronisation fix (Bob)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.

 2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
    properly.  From Ezequiel Garcia.

 3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.

 4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.

 5) Fix deadlock on team->lock when propagating features, from Ivan
    Vecera.

 6) Work around buffer offset hw bug in alx chips, from Feng Tang.

 7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
    Long.

 8) Various statistics bug fixes in mlx4 from Eric Dumazet.

 9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.

10) All of l2tp was namespace aware, but the ipv6 support code was not
    doing so.  From Shmulik Ladkani.

11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.

12) Propagate MAC changes properly through VLAN devices, from Mike
    Manning.

13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  sfc: Track RPS flow IDs per channel instead of per function
  usbnet: smsc95xx: fix link detection for disabled autonegotiation
  virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
  bnx2x: avoid leaking memory on bnx2x_init_one() failures
  fou: fix IPv6 Kconfig options
  openvswitch: update checksum in {push,pop}_mpls
  sctp: sctp_diag should dump sctp socket type
  net: fec: update dirty_tx even if no skb
  vlan: Propagate MAC address to VLANs
  atm: iphase: off by one in rx_pkt()
  atm: firestream: add more reserved strings
  vxlan: Accept user specified MTU value when create new vxlan link
  net: pktgen: Call destroy_hrtimer_on_stack()
  timer: Export destroy_hrtimer_on_stack()
  net: l2tp: Make l2tp_ip6 namespace aware
  Documentation: ip-sysctl.txt: clarify secure_redirects
  sfc: use flow dissector helpers for aRFS
  ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
  net: nps_enet: Disable interrupts before napi reschedule
  net/lapb: tuse %*ph to dump buffers
  ...

Pull sparc fixes from David Miller:
 "sparc64 mmu context allocation and trap return bug fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix return from trap window fill crashes.
  sparc: Harden signal return frame checks.
  sparc64: Take ctx_alloc_lock properly in hugetlb_setup().

Otherwise we get confused when two flows on different channels get the
 same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function virtnet_open() and virtnet_probe(), func try_fill_recv() may
be executed at the same time. VQ in virtqueue_add() has not been protected
well and BUG_ON will be triggered when virito_net.ko being removed.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.

Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.

After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.

I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of CHECKSUM_COMPLETE the skb checksum should be updated in
{push,pop}_mpls() as they the type in the ethernet header.

As suggested by Pravin Shelar.

Cc: Pravin Shelar <pshelar@nicira.com>
Fixes: 25cd9ba0 ("openvswitch: Add basic MPLS support to kernel")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we cannot distinguish that one sk is a udp or sctp style when
we use ss to dump sctp_info. it's necessary to dump it as well.

For sctp_diag, ss support is not officially available, thus there
are no official users of this yet, so we can add this field in the
middle of sctp_info without breaking user API.

v1->v2:
  - move 'sctpi_s_type' field to the end of struct sctp_info, so
    that it won't cause incompatibility with applications already
    built.
  - add __reserved3 in sctp_info to make sure sctp_info is 8-byte
    alignment.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If dirty_tx isn't updated, then dma_unmap_single
can be called twice.

This fixes a
[   58.420980] ------------[ cut here ]------------
[   58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[   58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]

encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC address of the physical interface is only copied to the VLAN
when it is first created, resulting in an inconsistency after MAC
address changes of only newly created VLANs having an up-to-date MAC.

The VLANs should continue inheriting the MAC address of the physical
interface until the VLAN MAC address is explicitly set to any value.
This allows IPv6 EUI64 addresses for the VLAN to reflect any changes
to the MAC of the physical interface and thus for DAD to behave as
expected.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The iadev->rx_open[] array holds "iadev->num_vc" pointers (this code
assumes that pointers are 32 bits).  So the > here should be >= or else
we could end up reading a garbage pointer from one element beyond the
end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug was there when the driver was first added in back in year 2000.
It causes a Smatch warning:

    drivers/atm/firestream.c:849 process_incoming()
    error: buffer overflow 'res_strings' 60 <= 63

There are supposed to be 64 entries in this array and the missing
strings are clearly in the 30 40 range.  I added them as reserved 37 to
reserved 40.  It's possible that strings are really supposed to be added
in the middle instead of at the end, but this approach is safe, in that
it fixes the bug and doesn't break anything that wasn't already broken.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When create a new vxlan link, example:
  ip link add vtap mtu 1440 type vxlan vni 1 dev eth0

The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.

This problem was introduced by commit 0dfbdf41 (vxlan: Factor out device
configuration).

Fixes: 0dfbdf41 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If CONFIG_DEBUG_OBJECTS_TIMERS=y, hrtimer_init_on_stack() requires
a matching call to destroy_hrtimer_on_stack() to clean up timer
debug objects.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>