- 07 Jul, 2019 2 commits
-
-
Lang Cheng authored
The format specifier \"%p\" can leak kernel addresses. Use \"%pK\" instead. Signed-off-by:
Lang Cheng <chenglang@huawei.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com>
-
Lijun Ou authored
The buffer size of qp which used to allocate qp buffer space for storing sqwqe and rqwqe will be the length of buffer space. The kernel driver will use the buffer address and the same size to get the user memory. The same size named buff_size of qp. According the algorithm of calculating, The size of the two is not equal when users set the max sge of sq. Fixes: b28ca7cc ("RDMA/hns: Limit extend sq sge num") Signed-off-by:
Lijun Ou <oulijun@huawei.com> Signed-off-by:
-
- 05 Jul, 2019 21 commits
-
-
Lang Cheng authored
When hw resetting, there is no response from hw when driver sending cmdq. If driver still send cmdq to hw, the reset process may be blocked. So reset flag should be set to intercept the cmdq command when driver receiving "notify down" signal. Signed-off-by:
-
Yangyang Li authored
Currently, the depth of cq only supports 64K. According to the UM, the depth of cq is up to 4M, Therefore the ba page size of cqe was modified to support the maximum specification of cq depth. Signed-off-by:
Yangyang Li <liyangyang20@huawei.com> Signed-off-by:
-
chenglang authored
Hip06 reserve 12 qps, Hip08 reserve 8 qps. When the QP is released, the chip model is not judged, and the Hip08 cannot release the qpn 8~12 Signed-off-by:
-
Lijun Ou authored
It uses hns_roce_mtr_init in hns_roce_create_qp_common function. As a result, it should use hns_roce_mtr_cleanup function for cleaning mtr when destroying qp. Fixes: 8d18ad83 ("RDMA/hns: Fix bug when wqe num is larger than 16K") Signed-off-by:
Xi Wang <wangxi11@huawei.com> Signed-off-by:
-
Mark Zhang authored
This patch adds the ability to return the hwstats of per-port default counters (which can also be queried through sysfs nodes). Signed-off-by:
Mark Zhang <markz@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Mark Zhang authored
Provide an option to get current counter mode through RDMA netlink. Signed-off-by:
Majd Dibbiny <majd@mellanox.com> Signed-off-by:
-
Mark Zhang authored
Provide an option to allow users to manually bind a qp with a counter through RDMA netlink. Limit it to users with ADMIN capability only. Signed-off-by:
-
Mark Zhang authored
In manual mode a QP is bound to a counter manually. If counter is not specified then a new one will be allocated. Manual mode is enabled when user binds a QP, and disabled when the last manually bound QP is unbound. When auto-mode is turned off and there are counters left, manual mode is enabled so that the user is able to access these counters. Signed-off-by:
-
Mark Zhang authored
Since a QP can only be bound to one counter, then if it is bound to a separate counter, for backward compatibility purpose, the statistic value must be: * stat of default counter + stat of all running allocated counters + stat of all deallocated counters (history stats) Signed-off-by:
-
Mark Zhang authored
Add support for ib callback counter_alloc_stats() and counter_update_stats(). Signed-off-by:
-
Mark Zhang authored
This patch adds the ability to return all available counters together with their properties and hwstats. Signed-off-by:
-
Mark Zhang authored
Provide an option to enable/disable per-port counter auto mode through RDMA netlink. Limit it to users with ADMIN capability only. Signed-off-by:
-
Mark Zhang authored
Add support for ib callbacks counter_bind_qp(), counter_unbind_qp() and counter_dealloc(). Signed-off-by:
-
Mark Zhang authored
Add counter set id as a parameter so that this API can be used for querying any q counter. Signed-off-by:
-
Mark Zhang authored
Support bind a qp with counter. If counter is null then bind the qp to the default counter. Different QP state has different operation: - RESET: Set the counter field so that it will take effective during RST2INIT change; - RTS: Issue an RTS2RTS change to update the QP counter; - Other: Set the counter field and mark the counter_pending flag, when QP is moved to RTS state and this flag is set, then issue an RTS2RTS modification to update the counter. Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Mark Zhang authored
In auto mode all QPs belong to one category are bind automatically to a single counter set. Currently only "qp type" is supported. In this mode the qp counter is set in RST2INIT modification, and when a qp is destroyed the counter is unbound. Signed-off-by:
-
Mark Zhang authored
Add an API to support set/clear per-port auto mode. Signed-off-by:
-
Mark Zhang authored
Remove is_visible_in_pid_ns() from nldev.c and make it as a restrack API, so that it can be taken advantage by other parts like counter. Signed-off-by:
-
Mark Zhang authored
Add rdma_restrack_attach_task() which is able to attach a task other then "current" to a resource. Signed-off-by:
-
Mark Zhang authored
Introduce statistic counter as a new resource. It allows a user to monitor specific objects (e.g., QPs) by binding to a counter. In some cases a user counter resource is created with task other then "current", because its creation is done as part of rdmatool call. Signed-off-by:
-
Jason Gunthorpe authored
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux Required for dependencies in the next patches. * mlx5-next: net/mlx5: Add rts2rts_qp_counters_set_id field in hca cap net/mlx5: Properly name the generic WQE control field net/mlx5: Introduce TLS TX offload hardware bits and structures net/mlx5: Refactor mlx5_esw_query_functions for modularity net/mlx5: E-Switch prepare functions change handler to be modular net/mlx5: Introduce and use mlx5_eswitch_get_total_vports()
-
- 04 Jul, 2019 6 commits
-
-
Mark Zhang authored
Add rts2rts_qp_counters_set_id field in hca cap so that RTS2RTS qp modification can be used to change the counter of a QP. Signed-off-by:
-
Daniel Kranzdorf authored
Make admin commands id easier to distinguish by using relevant bits from the producer counter. This allows us to differentiate admin commands with the same producer index (happens after admin queue overlap), which is helpful when debugging. Signed-off-by:
Daniel Kranzdorf <dkkranzd@amazon.com> Reviewed-by:
Firas JahJah <firasj@amazon.com> Reviewed-by:
Yossi Leybovich <sleybo@amazon.com> Signed-off-by:
Gal Pressman <galpress@amazon.com> Signed-off-by:
-
Valentine Fatiev authored
Despite failure in ipoib_dev_init() we continue with initialization flow and creation of child device. It causes to the situation where this child device is added too early to parent device list. Change the logic, so in case of failure we properly return error from ipoib_dev_init() and add child only in success path. Fixes: eaeb3984 ("IB/ipoib: Move init code to ndo_init") Signed-off-by:
Valentine Fatiev <valentinef@mellanox.com> Reviewed-by:
Feras Daoud <ferasda@mellanox.com> Signed-off-by:
-
Leon Romanovsky authored
There is no need in custom memory zeroing, because it can be done by using kzalloc from the beginning. Signed-off-by:
-
Colin Ian King authored
The variable ret is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
-
Lijun Ou authored
The patch below wasn't fully tested for all combinations of module and configs, and causes a compile failure: WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_ah.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_alloc.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_cmd.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_cq.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_db.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_hem.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_mr.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_pd.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_qp.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_restrack.o see include/linux/module.h for more information WARNING: modpost: missing MODULE_LICENSE() in drivers/infiniband/hw/hns/hns_roce_srq.o see include/linux/module.h for more information ERROR: "hns_roce_bitmap_cleanup" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_bitmap_init" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_free_cmd_mailbox" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_alloc_cmd_mailbox" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_table_get" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_bitmap_alloc" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! ERROR: "hns_roce_table_find" [drivers/infiniband/hw/hns/hns_roce_srq.ko] undefined! The fix is to put the module sub components in the right line. Fixes: e9816ddf ("RDMA/hns: Cleanup unnecessary exported symbols") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- 03 Jul, 2019 11 commits
-
-
Yishai Hadas authored
No need any more to hold mlx5_core_dev on the devx_object, it can be accessed from ib_dev. Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
-
Yishai Hadas authored
Add DEVX support for CQ events by creating and destroying the CQ via mlx5_core and set an handler to manage its completions. Signed-off-by:
-
Yishai Hadas authored
Implement DEVX dispatching event by looking up for the applicable subscriptions for the reported event and using their target fd to signal/set the event. Signed-off-by:
-
Yishai Hadas authored
Enable subscription for device events over DEVX. Each subscription is added to the two level xarray data structure according to its event number and the DEVX object information in case was given with the given target fd. Those events will be reported over the given fd once will occur. Downstream patches will mange the dispatching to any subscription. Signed-off-by:
-
Yishai Hadas authored
Register DEVX with with mlx5_core to get async events. This will enable to dispatch the applicable events to its consumers in down stream patches. Signed-off-by:
-
Yishai Hadas authored
Introduce MLX5_IB_OBJECT_DEVX_ASYNC_EVENT_FD and its initial implementation. This object is from type class FD and will be used to read DEVX async events. Signed-off-by:
-
Tariq Toukan authored
A generic WQE control field is used for different purposes in different cases. Use union to allow using the proper name in each case. Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Eran Ben Elisha authored
Add TLS offload related IFC structs, layouts and enumerations. Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Parav Pandit authored
Functions change event output data size changes when functions other than VFs will be enabled in HCA CAP. With current API, multiple callers needs to align, calculate accurate size of the output data depending on number on non VF functions enabled in the device. Instead of duplicating such math at multiple places, refactor mlx5_esw_query_functions() to return raw output allocated by itself. Caller must free the allocated memory using kvfree() as described in the function comment section. This hides calcuation within mlx5_esw_query_functions() and provides simpler API. Signed-off-by:
Parav Pandit <parav@mellanox.com> Signed-off-by:
-
Parav Pandit authored
Eswitch function change handler will service multiple type of events for VFs and non VF functions update. Hence, introduce and use the helper function esw_vfs_changed_event_handler() for handling change in num VFs to improve the code readability. Signed-off-by:
-
Parav Pandit authored
Instead MLX5_TOTAL_VPORTS, use mlx5_eswitch_get_total_vports(). mlx5_eswitch_get_total_vports() in subsequent patch accounts for SF vports as well. Expanding MLX5_TOTAL_VPORTS macro would require exposing SF internals to more generic vport.h header file. Such exposure is not desired. Hence a mlx5_eswitch_get_total_vports() is introduced. Given that mlx5_eswitch_get_total_vports() API wants to work on const mlx5_core_dev*, change its helper functions also to accept const *dev. Signed-off-by:
-
