Add note about recent updates coming from Microsoft's publicly available
specs on Windows Media Center remotes and receivers/transmitters.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Rather than dumping out hex values, lets print the actual calculated
frequency and period the hardware has been configured for. After this

[ 2643.276215] mceusb 3-1:1.0: tx data: 9f 07 (length=2)
[ 2643.276218] mceusb 3-1:1.0: Get carrier mode and freq
[ 2643.277206] mceusb 3-1:1.0: rx data: 9f 06 01 42 (length=4)
[ 2643.277209] mceusb 3-1:1.0: Got carrier of 37037 Hz (period 27us)

Matches up perfectly with the table in Microsoft's docs.

Of course, I've noticed on one of my devices that the MS-recommended
default value of 1 for carrier pre-scaler and 66 for carrier period was
butchered, and instead of converting 66 to hex (0x42 like above), they
put in 0x66, so the hardware reports a default carrier of 24390Hz.
Fortunately, I guess, this particular device is rx-only, but I wouldn't
put it past other hw to screw up here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

According to the specs, you can read the number of tx ports, number of
rx sensors, which tx ports have cables plugged into them, and which rx
sensors are active. In practice, most of my devices do seem to report
sane values for tx ports and rx sensors (but not all -- one without any
tx ports reports having them), and most report the active sensor
correctly, but only one of eight reports cabled tx ports correctly. So
for the most part, this is just for informational purposes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Supposedly, there are essentially three different classes of devices
that are compatible with Microsoft's specs. First are the "legacy"
devices, which are built using Microsoft-provided hardware specs and
firmware. Second are "emulator" devices, which are built using custom
hardware and firmware, written to emulate Microsoft's firmware. Third
are "port" devices, which have their own device driver and firmware,
which provides compatible data to higher levels of the stack.

>From what I can tell, things like nuvoton-cir and fintek-cir are
essentially "port" devices -- their raw IR buffer format is very similar
to that of the mceusb devices. Now, within the mceusb driver, we have
three different "generations", which at first, seemed like maybe they
mapped to emulator versions. Unfortuantely, every single device I have
responds "illegal command" to the query to get firmware emulator version
from the hardware, which means they're either all emulator version 1, or
they're legacy devices, and our different "generations" aren't at all
related here. Though in theory, its possible the gen1 devices are
"legacy" devices and the rest are emulator v1. There are some useful
features of the v2 interface I was hoping to play with, but alas...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

According to MS docs, the device firmware may halt after receiving an
unknown instruction, but that it should be possible to tell the firmware
to continue running by simply sending a device resume command. So lets
do that.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Its not uncommon for folks to force these bits enabled, because people
do want to wake their htpc kit via their remote. Lets just set the bits
for 'em.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Sometimes the init routine is blasting commands out to the hardware
faster than it can reply. Throw a brief delay in there to give the
hardware a chance to reply before we send the next command.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I was recently pointed to the document titled
Windows-Media-Center-RC-IR-Collection-Green-Button-Specification-03-08-2011-V2.pdf
which as of this writing, is publicly available from
download.microsoft.com. It covers a LOT of the gaps in the mceusb
driver, which to this point, was written almost entirely by
reverse-engineering. First up, I'm updating the defines for all the MCE
commands and responses to match their names in the spec. More to come...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

tda827x is currently taking the demod IF frequency into account while
seeking for the proper tuner range. This is wrong, as the demod IF
frequency has nothing to do with the tuner PLL.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Hello,

When migrating from Slackware 13.1 to 13.37 (kernel 2.6.33.x to
2.6.37.6), there was some sort of regression with the external webcam
installed at the notebook (0x45:6128, SN9C325+OM6802).

In the version 2.6.37.6, the images got *very* dark, making the webcam
almost unusable, unless if used with direct sunlight.

Tracing back what happened, I concluded that changeset 0e4d413a
caused some sort of odd effects - including this - to this specific model.
Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br>
Acked-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

There are folks with flaky imon hardware out there that doesn't always
respond to requests to write to their displays for some reason, which
can flood logs quickly when something like lcdproc is trying to
constantly update the display, so lets rate-limit all that error spew.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

If the bus has been reset on resume, set the alternate setting to 0.
This should be the default value, but some devices crash or otherwise
misbehave if they don't receive a SET_INTERFACE request before any other
video control request.

Microdia's 0c45:6437 camera has been found to require this change or it
will stop sending video data after resume.

uvc_video.c]
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This device is not using the proper demod IF. Instead of using the
IF macro, it is specifying a IF frequency. This doesn't work, as xc3028
needs to load an specific SCODE for the tuner. In this case, there's
no IF table for 5 MHz.

Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Move documentation of structures used in DQEVENT from SUBSCRIBE_EVENT to
DQEVENT.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Potentially the adp1653_init_controls could return an error. In our case the
error was ignored, meanwhile it means incorrect initialization of V4L2
controls. Additionally we have to free control handler structures in case of
apd1653_init_controls or media_entity_init failure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The driver requires platform_data to be present. That's why we need to check
and fail in case of the absence of necessary data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The goal of this patch is to correct a previous patch. In case of error,
the err() function should be used instead of dprintk() function.

[mchehab@redhat.com: as I've replaced dprintk by deb_info, on the the
 previous patch, to avoid breaking bisect, I had to fix a merge conflict
 on this one]
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch protects the common buffer access inside the dib0700 in order
to manage concurrent access. This protection is done using mutex.

Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: stable@kernel.org
Signed-off-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
[mchehab@redhat.com: dprint requires 3 arguments. Replaced by dib_info]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch protects the I2C buffer access in order to manage concurrent
access. This protection is done using mutex.
Furthermore, for the dib9000, if a pid filtering command is
received during the tuning, this pid filtering command is delayed to
avoid any concurrent access issue.

Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: stable@kernel.org
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <Patrick.Boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Whan an ioctl is implemented, but the parameters are invalid,
the error code should be -EINVAL. However, if the ioctl is
not defined, it should return -ENOTTY instead.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Change adapter FE pointer as array of FE pointers.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The input stop() callback already calls the em28xx_ir_stop method.
Calling it again causes an oops.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

rc unregister logic were deadly broken, preventing some drivers to
be removed. Among the broken things, rc_dev_uevent() is being called
during device_del(), causing a data filling on an area that it is
not ready anymore.

Also, some drivers have a stop callback defined, that needs to be called
before data removal, as it stops data polling.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

No functional changes on this patch.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
  [media] ir-mce_kbd-decoder: include module.h for its facilities
  [media] ov5642: include module.h for its facilities
  [media] em28xx: Fix DVB-C maxsize for em2884
  [media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
  [media] v4l: mt9v032: Fix Bayer pattern
  [media] V4L: mt9m111: rewrite set_pixfmt
  [media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
  [media] V4L: initial driver for ov5642 CMOS sensor
  [media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
  [media] V4L: soc-camera: remove soc-camera bus and devices on it
  [media] V4L: soc-camera: un-export the soc-camera bus
  [media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
  [media] V4L: add media bus configuration subdev operations
  [media] V4L: soc-camera: group struct field initialisations together
  [media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
  [media] V4L: pxa-camera: switch to using standard PM hooks
  [media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
  [media] Don't OOPS if videobuf_dvb_get_frontend return NULL
  [media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
  [media] omap3isp: Support configurable HS/VS polarities
  ...

Fix up conflicts:
 - arch/arm/mach-omap2/board-rx51-peripherals.c:
     cleanup regulator supply definitions in mach-omap2
   vs
     OMAP3: RX-51: define vdds_csib regulator supply
 - drivers/staging/tm6000/tm6000-alsa.c (trivial)

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: Fix build breakage in xfs_iops.c when CONFIG_FS_POSIX_ACL is not set

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  ecryptfs: Make inode bdi consistent with superblock bdi
  eCryptfs: Unlock keys needed by ecryptfsd

* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/balloon: Fix compile errors - missing header files.
  xen/grant: Fix compile warning.
  xen/pciback: remove duplicated #include

remove unnecessary code that matches this coccinelle pattern

	if (...)
		return ret;
	return ret;
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes this:

  drivers/char/ramoops.c: In function 'ramoops_init':
  drivers/char/ramoops.c:221: error: implicit declaration of function 'IS_ERR'
  drivers/char/ramoops.c:222: error: implicit declaration of function 'PTR_ERR'

If it actually builds on other platforms, it's probably getting
linux/err.h via some other #include.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: remove printks about disabled bridge windows
  PCI: fold pci_calc_resource_flags() into decode_bar()
  PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
  PCI: correct pcie_set_readrq write size
  PCI: pciehp: change wait time for valid configuration access
  x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
  PCI: ARI is a PCIe v2 feature
  x86/PCI: quirks: Use pci_dev->revision
  PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
  PCI hotplug: cpqphp: use pci_dev->vendor
  PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
  x86/PCI: config space accessor functions should not ignore the segment argument
  PCI: Assign values to 'pci_obff_signal_type' enumeration constants
  x86/PCI: reduce severity of host bridge window conflict warnings
  PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
  PCI: PCIe AER: add aer_recover_queue
  x86/PCI: select direct access mode for mmconfig option
  PCI hotplug: Rename is_ejectable which also exists in dock.c

* 'upstream/xen-tracing2' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen/tracing: fix compile errors when tracing is disabled.

* 'at91/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  at91: add arch specific ioremap support
  at91: factorize sram init
  at91: move register clocks to soc generic init
  at91: move clock subsystem init to soc generic init
  at91: use structure to store the current soc
  at91: remove AT91_DBGU offset from dbgu register macro
  at91: factorize at91 interrupts init to soc
  at91: introduce commom AT91_BASE_SYS