Back in commit c03c2a87, we fixed logic in the non-bf54x
GPIO resume code to set the data levels properly before the direction
to avoid spurious line glitches.  But we missed the bf54x code paths.
So add the same fix there.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need to reload these registers constantly since they're always
available (we're not making any function calls in between).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The Blackfin C ABI says we do not need to save/restore R0-R3 and P0-P2
as they are available as scratch registers.  So don't bother.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Re-architect how we save/restore the gpio/port logic that only pertains
to bf538/bf539 parts by pulling it out of the core code paths and pushing
it out to bf538-specific locations.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The current save logic used in hibernation is to do a MMR load (base +
offset) into a register, and then push that onto the stack.  Then when
restoring, pop off the stack into a register followed by a MMR store
(base + offset).  These use plenty of 32bit insns rather than 16bit,
are pretty long winded, and full of pipeline bubbles.

So, by taking advantage of MMRs that are contiguous, the multi-register
push/pop insn, and register abuse, we can shrink this code considerably.

When saving, the new logic does a lot of loads into the data and pointer
registers before executing a single multi-register push insn.  Then when
restoring, we do a single multi-register pop insn followed by a lot of
stores.  Overall, this allows us to cut the insn count by ~30%, the code
size by ~45%, and drastically reduce the register hazards that trigger
bubbles in the pipeline.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

EVT0 is for emulation, EVT1 is for reset, and EVT4 is the "global int
disable" region.  None of these are used by software (or even hardware),
so don't bother saving/restoring them when we hibernate since nothing
ever uses these in Linux (the only thing they would be useful for is
core-memory scratch, but that's just crazy talk).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This defines only get used in the hibernate code, so remove them from the
global dpmc header as no one else cares.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The RETE/RETN registers are only used in emulation(JTAG) and NMI nodes,
or as scratch registers, neither of which need to be saved/restored as
this code doesn't execute at those core event levels.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

For parts with more than one SIC_IWR, we can optimize the writing
a little bit using better Blackfin insns.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Have the logic that uses peripheral interrupt blocks key off of pint
defines rather than CPU names so that things are generalized across
families.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Have the code work off of MMR names rather than CPU defines so there is
less code to tweak in the future with new parts.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Don't bind the code to specific CPU defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We have a struct in the headers describing the register layout, so
drop the local duplicate one.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The hardware block uses the name "request" rather than "irq", so update
the struct accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The array of pointers to register blocks never changes, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These defines don't accomplish much as GPIO_# is the same thing as #.
Each CPU already provides helpful symbolic defines like GPIO_<PIN>
which everyone uses, so just punt these # ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Not sure how these guys slipped in, but they're annoying me.
So bring these unicode space gremlins down to earth to normal
ascii spaces.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

For now, this only supports gptimers.  Support for dedicated PWM devices
as found on newer parts to come.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The API is geared around timer ids, except for the act of enabling
and disabling timers.  So add a small helper to fill out the gap.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The alignment is normally handled by PERCPU(), but we need to do it
ourselves in the XIP build due to the custom layout.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Use proper helper macros for reading/writing the MMRs rather than
volatile markings on the struct.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Now that asm/gptimers.h has the hardware register struct layout, there's
no need to duplicate things locally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Passing a non-simple expression in as the addr arg could incorrectly
apply the pointer cast resulting in misbehavior.  Add proper paren.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These flashes are always on the board, so might as well enable them by
default rather than a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The documentation for the IMDMA channels appears to be incorrect.
These DMA blocks don't actually have PERIPHERAL_MAP MMRs for us
to access.  Attempts to do so lead to system mmr hardware errors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The Blackfin mutex.h is merely a copy of an older asm-generic/mutex-dec.h,
so punt it and just use the common one directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This moves the double fault data used at boot time into a single struct
which can then easily be addressed with indexed loads rather than having
to explicitly load multiple addresses.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This just imports all of the optimization work done in the
common startup code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant.  So punt
those parts.

Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need for one line header stubs.  Just declare it in Kbuild.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86-64, vdso: Do not allocate memory for the vDSO
  clocksource: Change __ARCH_HAS_CLOCKSOURCE_DATA to a CONFIG option
  x86, vdso: Drop now wrong comment
  Document the vDSO and add a reference parser
  ia64: Replace clocksource.fsys_mmio with generic arch data
  x86-64: Move vread_tsc and vread_hpet into the vDSO
  clocksource: Replace vread with generic arch data
  x86-64: Add --no-undefined to vDSO build
  x86-64: Allow alternative patching in the vDSO
  x86: Make alternative instruction pointers relative
  x86-64: Improve vsyscall emulation CS and RIP handling
  x86-64: Emulate legacy vsyscalls
  x86-64: Fill unused parts of the vsyscall page with 0xcc
  x86-64: Remove vsyscall number 3 (venosys)
  x86-64: Map the HPET NX
  x86-64: Remove kernel.vsyscall64 sysctl
  x86-64: Give vvars their own page
  x86-64: Document some of entry_64.S
  x86-64: Fix alignment of jiffies variable

* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, UV: Correct UV2 BAU destination timeout
  x86, UV: Correct failed topology memory leak
  x86, UV: Remove cpumask_t from the stack
  x86, UV: Rename hubmask to pnmask
  x86, UV: Correct reset_with_ipi()
  x86, UV: Allow for non-consecutive sockets
  x86, UV: Inline header file functions
  x86, UV: Fix smp_processor_id() use in a preemptable region
  x66, UV: Enable 64-bit ACPI MFCG support for SGI UV2 platform
  x86, UV: Clean up uv_mmrs.h

Merge branch 'x86-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Kill handle_signal()->set_fs()
  x86, do_signal: Simplify the TS_RESTORE_SIGMASK logic
  x86, signals: Convert the X86_32 code to use set_current_blocked()
  x86, signals: Convert the IA32_EMULATION code to use set_current_blocked()