The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

phram was 32-bit limited by design. Machines are growing up, but phram
module is still useful. Update it. The patch is bigger than minimum,
because simple_strtoul() is obsolete.

Tested on MIPS64 and compile-tested for PPC (32 bit).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Reviewed-by: Joern Engel <joern@logfs.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This flashchip is used in D-Link DIR-610 A1 router board
and maybe several others, yet is not kernel upstream.

So add support for it according to datasheet [0], making it easier
to support other boards using this flashchip in the future.

[0] http://www.esmt.com.tw/DB/manager/upload/F25L32PA.pdfSigned-off-by: Flavio Silveira <fggs@terra.com.br>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Current code sets the mtd->type with MTD_NANDFLASH for both
SLC and MLC. So the jffs2 may supports the MLC nand, but in actually,
the jffs2 should not support the MLC.

This patch uses the nand_is_slc() to check the nand cell type,
and set the mtd->type with the right nand type.

After this patch, the jffs2 only supports the SLC nand.

The side-effect of this patch:
  Before this patch, the ioctl(MEMGETINFO) can only return with the
  MTD_NANDFLASH; but after this patch, the ioctl(MEMGETINFO) will
  return with the MTD_NANDFLASH for SLC, and MTD_MLCNANDFLASH for MLC.

  So the user applictions(such as mtd-utils) should also changes a little
  for this.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We should not support the MLC nand for jffs2. So if the nand type is
MLC, we quit immediatly.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The current mtd_type_show() misses the MTD_MLCNANDFLASH case.
This patch adds the case for it, and also updates the ABI.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The helper is for user applications, and it is just a copy of
the kernel helper: mtd_type_is_nand();
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This helper detects that whether the mtd's type is nand type.

Now, it's clear that the MTD_NANDFLASH stands for SLC nand only.
So use the mtd_type_is_nand() to replace the old check method
to do the nand type (include the SLC and MLC) check.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In current code, the MTD_NANDFLASH is used to represent both the SLC and
MLC. It is confusing to us.

By adding an explicit comment about these two macros, this patch makes it
clear that:
	MTD_NANDFLASH    : stands for SLC NAND,
	MTD_MLCNANDFLASH : stands for MLC NAND (including TLC).
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When we use the ECC info which is get from the nand chip's datasheet,
we may have some freed oob area now.

This patch rewrites the gpmi_ecc_write_oob() to implement the ecc.write_oob().
We also update the comment for gpmi_hw_ecclayout.

Yes! We can support the JFFS2 for the SLC nand now.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Print out the cell information for nand chip.

(Since the message is too long, this patch also splits the log
with two separate pr_info())
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The current code does not set the SLC/MLC information for onfi nand.
(This makes that the kernel treats all the onfi nand as SLC nand.)

This patch fills the cell information for ONFI nands.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The legacy ID NAND are all SLC.
This patch sets 1 to the @bits_per_cell for the legacy ID NAND,
which means they are all SLC.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The @cellinfo fields contains unused information, such as write caching,
internal chip numbering, etc. But we only use it to check the SLC or MLC.

This patch tries to make it more clear and simple, renames the @cellinfo
to @bits_per_cell.

In order to avoiding the bisect issue, this patch also does the following
changes:
  (0) add a macro NAND_CI_CELLTYPE_SHIFT to avoid the hardcode.

  (1) add a helper to parse out the cell type : nand_get_bits_per_cell()

  (2) parse out the cell type for extended-ID chips and the full-id nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add a helper to check if a nand chip is SLC or MLC.
This helper makes the code more readable.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If the ONFI extended parameter page gives codeword_size == 0, the
extended ECC information is corrupt and should not be used. Currently,
we (correctly) avoid using the information, but we don't report the
error to the caller, so the caller doesn't know that we didn't
initialize ecc_strength_ds and ecc_step_ds. Now the caller can warn the
user that it does not have sufficient information.

This also removes the false and useless "ONFI extended param page
detected" debug message (it was printed even on the aforementioned
corruption, and for the success case, we don't really want a print).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>

Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch also add a const keyword for the of_device_id of nfc.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Since the of specific code are declared in <linux/of_mtd.h> regardless
of CONFIG_OF. Remove the #if defined(CONFIG_OF) guard and use an
IS_ENABLED(CONFIG_OF) instead.

Thanks to Ezequiel Garcia's for this protype.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Nothing calls omap2_onenand_rephase(). And __adjust_timing() is only
called by omap2_onenand_rephase(). Remove these two unused functions.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The ONFI detection routine is too verbose in some cases and not verbose
enough in others. This patch refactors it to print only when there are
significant warnings/errors.

Probing in 16-bit mode:
  It is unnecessary to print until after the READID (address 20h)
  command. READID *has* to work properly in whatever bus width
  configuration we are in, or else no identification mode works. So we
  can silence some useless warnings on systems which come up in 16-bit
  mode and do not even respond with an O-N-F-I string.

Valid parameter page:
  Nobody needs to see this. Do we inform the user every time other
  hardware responds properly? Instead, add an error message if *no*
  uncorrupted parameter pages are found.

ONFI ECC:
  Most drivers don't yet use the reported minimum ECC values, so it
  shouldn't yet be a fatal condition if the extended parameter page is
  incorrect. But we should at least give a warning for the corner cases
  that we don't expect.

ONFI flash detected:
  Nobody needs to see this. This is the expected case, that we detect
  ONFI properly, or else it wasn't ONFI-compliant and is detected by
  some other routine.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

do_xxlock() is only used locally. This silences a sparse warning:

drivers/mtd/lpddr/lpddr_cmds.c:706:5: warning: no previous prototype for 'do_xxlock' [-Wmissing-prototypes]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

These variable assignments are never used (the variables are either
never used or are overwritten before use). This resolves some compiler
warnings like the following:

    drivers/mtd/onenand/onenand_base.c: In function 'flexonenand_get_boundary':
    drivers/mtd/onenand/onenand_base.c:3532:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
    drivers/mtd/onenand/onenand_base.c: In function 'onenand_probe':
    drivers/mtd/onenand/onenand_base.c:3838:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

This field is never used, except to print it out.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The mtd_block_isbad() interface already checks for this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

It's only used in this file.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

struct dataflash's 'partition' field is unused. Just remove it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Brownell <david-b@pacbell.net>

I removed the last non-nand_base users of this, and we shouldn't have
any more modules that need to access it. It's only non-static to share
between nand_base and nand_bbt.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We want the default nand_chip.scan_bbt() function, so just use the
proper indirection.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This driver is doing some strange logic here. If it doesn't have
flash-based BBT enabled, it allows nand_scan_tail() to scan the BBT. But
if it is using flash-based BBT, it tells nand_scan_tail() to skip
scanning, then it immediately calls the default BBT scanning function
itself.

As I read it, this logic is equivalent to the default nand_scan_tail()
behavior without interfering with NAND_SKIP_BBTSCAN or calling
nand_default_bbt() directly at all.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

There's no point in the low level driver doing the work that nand_base
already is doing; just let nand_base set the default BBT scanning
function.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>

Just like the rest of the subsystems, let's add the required no-op
functions to implement stubs when CONFIG_OF=n.

This prevents MTD drivers from having ugly ifdefs in their code,
and instead hide the ifdef monster in the header closet (far away
from people's sight).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Pull final mtd fixes from Brian Norris:
 "A few more last-minute regression fixes, prepared jointly by me and
  David Woodhouse:

   - Revert pxa3xx to its old name to avoid breaking existing
     'mtdparts=' boot strings.

   - Return GPMI NAND to its legacy ECC layout for backwards
     compatibility.  We will revisit this in 3.13.

  A note from David on the latter fix: 'This leaves a harmless cosmetic
  warning about an unused function.  At this point in the cycle I really
  don't care.'"

* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
  mtd: gpmi: fix ECC regression
  mtd: nand: pxa3xx: Fix registered MTD name

Pull vfs fixes (try two) from Al Viro:
 "nfsd performance regression fix + seq_file lseek(2) fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: always update file->f_pos in seq_lseek()
  nfsd regression since delayed fput()

The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.

Commit 2febcdf8 ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:

   We can not mount the ubifs which was created by the old NAND ECC layout.

This patch fixes this issue by reverting to the legacy ECC layout.

We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.

This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41

As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:

    char str1[32] = { 0 };
    char str2[32] = { 0 };
    int poffset = 10;
    int count = 20;

    /*open any seq file*/
    int fd = open("/proc/modules", O_RDONLY);

    pread(fd, str1, count, poffset);
    printf("pread:%s\n", str1);

    /*seek to where m->read_pos is*/
    lseek(fd, poffset+count, SEEK_SET);

    /*supposed to read from poffset+count, but this read from position 0*/
    read(fd, str2, count);
    printf("read:%s\n", str2);

out put:
pread:
 ck_netbios_ns 12665
read:
 nf_conntrack_netbios

/proc/modules:
nf_conntrack_netbios_ns 12665 0 - Live 0xffffffffa038b000
nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns, Live 0xffffffffa0386000

So we always update file->f_pos to offset in seq_lseek() to fix this issue.
Signed-off-by: Jiaxing Wang <hello.wjx@gmail.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull ARM SoC fixes from Olof Johansson:
 "There's really only one bugfix in this branch, which is a fix for
  timers on the integrator platform.  Since Linus Walleij is
  resurrecting support for the platform it seems valuable to get the fix
  into 3.12 even though the regression has been around a while.

  The rest are a handful of maintainers updates.  If you prefer to hold
  those until 3.13 then just merge the first patch on the branch which
  is the fix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Add maintainers entry for Rockchip SoCs
  MAINTAINERS: Tegra updates, and driver ownership
  MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
  ARM: integrator: deactivate timer0 on the Integrator/CP