Drivers that use the start method for netlink dumping rely on dumpit not
being called if start fails. For example, ila_xlat.c allocates memory
and assigns it to cb->args[0] in its start() function. It might fail to
do that and return -ENOMEM instead. However, even when returning an
error, dumpit will be called, which, in the example above, quickly
dereferences the memory in cb->args[0], which will OOPS the kernel. This
is but one example of how this goes wrong.

Since start() has always been a function with an int return type, it
therefore makes sense to use it properly, rather than ignoring it. This
patch thus returns early and does not call dumpit() when start() fails.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-fixes-2017-09-28

Misc. fixes for mlx5 drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_prot and sk->sk_prot_creator can differ when the app uses
IPV6_ADDRFORM (transforming an IPv6-socket to an IPv4-one).
Which is why sk_prot_creator is there to make sure that sk_prot_free()
does the kmem_cache_free() on the right kmem_cache slab.

Now, if such a socket gets transformed back to a listening socket (using
connect() with AF_UNSPEC) we will allocate an IPv4 tcp_sock through
sk_clone_lock() when a new connection comes in. But sk_prot_creator will
still point to the IPv6 kmem_cache (as everything got copied in
sk_clone_lock()). When freeing, we will thus put this
memory back into the IPv6 kmem_cache although it was allocated in the
IPv4 cache. I have seen memory corruption happening because of this.

With slub-debugging and MEMCG_KMEM enabled this gives the warning
	"cache_from_obj: Wrong slab cache. TCPv6 but object is from TCP"

A C-program to trigger this:

void main(void)
{
        int fd = socket(AF_INET6, SOCK_STREAM, IPPROTO_TCP);
        int new_fd, newest_fd, client_fd;
        struct sockaddr_in6 bind_addr;
        struct sockaddr_in bind_addr4, client_addr1, client_addr2;
        struct sockaddr unsp;
        int val;

        memset(&bind_addr, 0, sizeof(bind_addr));
        bind_addr.sin6_family = AF_INET6;
        bind_addr.sin6_port = ntohs(42424);

        memset(&client_addr1, 0, sizeof(client_addr1));
        client_addr1.sin_family = AF_INET;
        client_addr1.sin_port = ntohs(42424);
        client_addr1.sin_addr.s_addr = inet_addr("127.0.0.1");

        memset(&client_addr2, 0, sizeof(client_addr2));
        client_addr2.sin_family = AF_INET;
        client_addr2.sin_port = ntohs(42421);
        client_addr2.sin_addr.s_addr = inet_addr("127.0.0.1");

        memset(&unsp, 0, sizeof(unsp));
        unsp.sa_family = AF_UNSPEC;

        bind(fd, (struct sockaddr *)&bind_addr, sizeof(bind_addr));

        listen(fd, 5);

        client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
        connect(client_fd, (struct sockaddr *)&client_addr1, sizeof(client_addr1));
        new_fd = accept(fd, NULL, NULL);
        close(fd);

        val = AF_INET;
        setsockopt(new_fd, SOL_IPV6, IPV6_ADDRFORM, &val, sizeof(val));

        connect(new_fd, &unsp, sizeof(unsp));

        memset(&bind_addr4, 0, sizeof(bind_addr4));
        bind_addr4.sin_family = AF_INET;
        bind_addr4.sin_port = ntohs(42421);
        bind(new_fd, (struct sockaddr *)&bind_addr4, sizeof(bind_addr4));

        listen(new_fd, 5);

        client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
        connect(client_fd, (struct sockaddr *)&client_addr2, sizeof(client_addr2));

        newest_fd = accept(new_fd, NULL, NULL);
        close(new_fd);

        close(client_fd);
        close(new_fd);
}

As far as I can see, this bug has been there since the beginning of the
git-days.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_g2_irq_free locks the registers mutex, but not
mv88e6xxx_g1_irq_free, which results in a stack trace from
assert_reg_lock when unloading the mv88e6xxx module. Fix this.

Fixes: 3460a577 ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packet socket option po->has_vnet_hdr can be updated concurrently with
other operations if no ring is attached.

Do not test the option twice in packet_snd, as the value may change in
between calls. A race on setsockopt disable may cause a packet > mtu
to be sent without having GSO options set.

Fixes: bfd5f4a3 ("packet: Add GSO/csum offload support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once a socket has po->fanout set, it remains a member of the group
until it is destroyed. The prot_hook must be constant and identical
across sockets in the group.

If fanout_add races with packet_do_bind between the test of po->fanout
and taking the lock, the bind call may make type or dev inconsistent
with that of the fanout group.

Hold po->bind_lock when testing po->fanout to avoid this race.

I had to introduce artificial delay (local_bh_enable) to actually
observe the race.

Fixes: dc99f600 ("packet: Add fanout support.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-enable the MAC receiver by setting CONFIG_RE before powering down,
as instructed in section 6.3.5.1 of [1].  Without this the MAC fails
to receive WoL packets and never wakes up.

[1] DWC Ethernet QoS Databook 4.10a October 2014
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add hook to stmmac_pltfr_pm_ops for suspend / resume handling.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We cannot be registering the network device first, then setting its
carrier off and finally connecting it to a PHY, doing that leaves a
window during which the carrier is at best inconsistent, and at worse
the device is not usable without a down/up sequence since the network
device is visible to user space with possibly no PHY device attached.

Re-order steps so that they make logical sense. This fixes some devices
where the port was not usable after e.g: an unbind then bind of the
driver.

Fixes: 0071f56e ("dsa: Register netdev before phy")
Fixes: 91da11f8 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ports with the same VLAN must all be in the same bridge. However the
CPU and DSA ports need to be in multiple VLANs spread over multiple
bridges. So exclude them when performing this test.

Fixes: b2f81d30 ("net: dsa: add CPU and DSA ports as VLAN members")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My prior fix was not complete, as we were dereferencing a pointer
three times per node, not twice as I initially thought.

Fixes: 4cc5b44b ("inetpeer: fix RCU lookup()")
Fixes: b145425f ("inetpeer: remove AVL implementation in favor of RB tree")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: various fixes

This series contains 3 fixes for the Marvell PPv2 driver.

Since v1:
  - Removed one patch about dma masks as it would need a better fix.
  - Added one fix about the MAC Tx clock source selection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).

Fixes: 3919357f ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.

This fixes the issue by using an index not equal to the value of the
port-id property.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KMSAN (https://github.com/google/kmsan) reported accessing uninitialized
skb->data[0] in the case the skb is empty (i.e. skb->len is 0):

================================================
BUG: KMSAN: use of uninitialized memory in tun_get_user+0x19ba/0x3770
CPU: 0 PID: 3051 Comm: probe Not tainted 4.13.0+ #3140
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
...
 __msan_warning_32+0x66/0xb0 mm/kmsan/kmsan_instr.c:477
 tun_get_user+0x19ba/0x3770 drivers/net/tun.c:1301
 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365
 call_write_iter ./include/linux/fs.h:1743
 new_sync_write fs/read_write.c:457
 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470
 vfs_write+0x3e4/0x770 fs/read_write.c:518
 SYSC_write+0x12f/0x2b0 fs/read_write.c:565
 SyS_write+0x55/0x80 fs/read_write.c:557
 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284
 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:245
...
origin:
...
 kmsan_poison_shadow+0x6e/0xc0 mm/kmsan/kmsan.c:211
 slab_alloc_node mm/slub.c:2732
 __kmalloc_node_track_caller+0x351/0x370 mm/slub.c:4351
 __kmalloc_reserve net/core/skbuff.c:138
 __alloc_skb+0x26a/0x810 net/core/skbuff.c:231
 alloc_skb ./include/linux/skbuff.h:903
 alloc_skb_with_frags+0x1d7/0xc80 net/core/skbuff.c:4756
 sock_alloc_send_pskb+0xabf/0xfe0 net/core/sock.c:2037
 tun_alloc_skb drivers/net/tun.c:1144
 tun_get_user+0x9a8/0x3770 drivers/net/tun.c:1274
 tun_chr_write_iter+0x19f/0x300 drivers/net/tun.c:1365
 call_write_iter ./include/linux/fs.h:1743
 new_sync_write fs/read_write.c:457
 __vfs_write+0x6c3/0x7f0 fs/read_write.c:470
 vfs_write+0x3e4/0x770 fs/read_write.c:518
 SYSC_write+0x12f/0x2b0 fs/read_write.c:565
 SyS_write+0x55/0x80 fs/read_write.c:557
 do_syscall_64+0x242/0x330 arch/x86/entry/common.c:284
 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:245
================================================

Make sure tun_get_user() doesn't touch skb->data[0] unless there is
actual data.

C reproducer below:
==========================
    // autogenerated by syzkaller (http://github.com/google/syzkaller)

    #define _GNU_SOURCE

    #include <fcntl.h>
    #include <linux/if_tun.h>
    #include <netinet/ip.h>
    #include <net/if.h>
    #include <string.h>
    #include <sys/ioctl.h>

    int main()
    {
      int sock = socket(PF_INET, SOCK_STREAM, IPPROTO_IP);
      int tun_fd = open("/dev/net/tun", O_RDWR);
      struct ifreq req;
      memset(&req, 0, sizeof(struct ifreq));
      strcpy((char*)&req.ifr_name, "gre0");
      req.ifr_flags = IFF_UP | IFF_MULTICAST;
      ioctl(tun_fd, TUNSETIFF, &req);
      ioctl(sock, SIOCSIFFLAGS, "gre0");
      write(tun_fd, "hi", 0);
      return 0;
    }
==========================
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Smatch is screaming:

drivers/net/ethernet/mellanox/mlx5/core/sriov.c:112
	mlx5_device_enable_sriov() warn: inconsistent indenting

fix that.

Fixes: 7ecf6d8f ('IB/mlx5: Restore IB guid/policy for virtual functions')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix this sparse complaint:

drivers/net/ethernet/mellanox/mlx5/core/./diag/fs_tracepoint.h:172:1:
	warning: odd constant _Bool cast (ffffffffffffffff becomes 1)

Fixes: d9fea79171ee ('net/mlx5: Add tracepoints')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Instead of calculating the offloads counters, count them explicitly.
The calculations done for these counters would result in bugs in some
cases, for example:
When running TCP traffic over a VXLAN tunnel with TSO enabled the following
counters would increase:
       tx_csum_partial: 1,333,284
       tx_csum_partial_inner: 29,286
       tx4_csum_partial_inner: 384
       tx7_csum_partial_inner: 8
       tx9_csum_partial_inner: 34
       tx10_csum_partial_inner: 26,807
       tx11_csum_partial_inner: 287
       tx12_csum_partial_inner: 27
       tx16_csum_partial_inner: 6
       tx25_csum_partial_inner: 1,733

Seems like tx_csum_partial increased out of nowhere.
The issue is in the following calculation in mlx5e_update_sw_counters:
s->tx_csum_partial = s->tx_packets - tx_offload_none - s->tx_csum_partial_inner;

While tx_packets increases by the number of GSO segments for each SKB,
tx_csum_partial_inner will only increase by one, resulting in wrong
tx_csum_partial counter.

Fixes: bfe6d8d1 ("net/mlx5e: Reorganize ethtool statistics")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Toggling of C-tag VLAN filter should not affect the "any S-tag" steering rule.

Fixes: 8a271746 ("net/mlx5e: Receive s-tagged packets in promiscuous mode")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use the correct formatting for netdev features.

Fixes: 0e405443 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Encap entries cached by the driver could be invalidated due to
tunnel destination neighbour state changes.
When attempting to offload a flow that uses a cached encap entry,
we must check the entry validity and defer the offloading
if the entry exists but not valid.

When EAGAIN is returned, the flow offloading to hardware takes place
by the neigh update code when the tunnel destination neighbour
becomes connected.

Fixes: 232c0013 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When offloading header re-write, the HW may need to adjust checksums along
the packet. For IP traffic, and a case where we are asked to modify fields in
the IP header, current HW supports that only for TCP and UDP. Enforce it, in
this case fail the offloading attempt for non TCP/UDP packets.

Fixes: d7e75a32 ('net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions')
Fixes: 2f4fe4ca ('net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In case the neighbour for the tunnel destination isn't valid,
we send a neighbour update request but we free the encap
header buffer. This is wrong, because we still need it for
allocating a HW encap entry once the neighbour is available.

Fix that by skipping freeing it if we wait for neighbour.

Fixes: 232c0013 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Added check for the maximal number of flow counters attached
to rule (FTE).

Fixes: bd5251db ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.

Fixes: e29341fb ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When cleaning rdma netdevice we need to save the mdev pointer
because priv is released when we release netdev.

This bug was found using the kernel address sanitizer (KASAN).
use-after-free in mlx5_rdma_netdev_free+0xe3/0x100 [mlx5_core]

Fixes: 48935bbb ("net/mlx5e: IPoIB, Add netdevice profile skeleton")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The sctp_for_each_transport() function takes an pointer to int.  The
cb->args[] array holds longs so it's only using the high 32 bits.  It
works on little endian system but will break on big endian 64 bit
machines.

Fixes: d25adbeb ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.14

Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.

iwlwifi

* a couple of bugzilla bugs related to multicast handling

* two fixes for WoWLAN bugs that were causing queue hangs and
  re-initialization problems

* two fixes for potential uninitialized variable use reported by Dan
  Carpenter in relation to a recently introduced patch

* a fix for buffer reordering in the newly supported 9000 device
  family

* fix a race when starting aggregation

* small fix for a recent patch to wake mac80211 queues

* send non-bufferable management frames in the generic queue so they
  are not sent on queues that are under power-save

ath10k

* fix a PCI PM related gcc warning

brcmfmac

* CVE-2017-0786: add length check scan results from firmware

* respect passive scan requests from user space

qtnfmac

* fix race in tx path when using multiple interfaces

* cancel ongoing scan when removing the wireless interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
aquantia: Atlantic driver bugfixes und improvements

This series contains bugfixes for aQuantia Atlantic driver.

Changes in v2:
Review comments applied:
- min_mtu set removed
- extra mtu range check is removed
- err codes handling improved
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.

This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
  link changes.
- introduces new constant for minimum descriptors count required for queue
  wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).

Fixes: 5513e164 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we try to delete the same tunnel twice, the first delete operation
does a lookup (l2tp_tunnel_get), finds the tunnel, calls
l2tp_tunnel_delete, which queues it for deletion by
l2tp_tunnel_del_work.

The second delete operation also finds the tunnel and calls
l2tp_tunnel_delete. If the workqueue has already fired and started
running l2tp_tunnel_del_work, then l2tp_tunnel_delete will queue the
same tunnel a second time, and try to free the socket again.

Add a dead flag to prevent firing the workqueue twice. Then we can
remove the check of queue_work's result that was meant to prevent that
race but doesn't.

Reproducer:

    ip l2tp add tunnel tunnel_id 3000 peer_tunnel_id 4000 local 192.168.0.2 remote 192.168.0.1 encap udp udp_sport 5000 udp_dport 6000
    ip l2tp add session name l2tp1 tunnel_id 3000 session_id 1000 peer_session_id 2000
    ip link set l2tp1 up
    ip l2tp del tunnel tunnel_id 3000
    ip l2tp del tunnel tunnel_id 3000

Fixes: f8ccac0e ("l2tp: put tunnel socket release on a workqueue")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running LTP IPsec tests, KASan might report:

BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0
...
Call Trace:
  <IRQ>
  dump_stack+0x63/0x89
  print_address_description+0x7c/0x290
  kasan_report+0x28d/0x370
  ? vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  __asan_report_load4_noabort+0x19/0x20
  vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
  ? vti_init_net+0x190/0x190 [ip_vti]
  ? save_stack_trace+0x1b/0x20
  ? save_stack+0x46/0xd0
  dev_hard_start_xmit+0x147/0x510
  ? icmp_echo.part.24+0x1f0/0x210
  __dev_queue_xmit+0x1394/0x1c60
...
Freed by task 0:
  save_stack_trace+0x1b/0x20
  save_stack+0x46/0xd0
  kasan_slab_free+0x70/0xc0
  kmem_cache_free+0x81/0x1e0
  kfree_skbmem+0xb1/0xe0
  kfree_skb+0x75/0x170
  kfree_skb_list+0x3e/0x60
  __dev_queue_xmit+0x1298/0x1c60
  dev_queue_xmit+0x10/0x20
  neigh_resolve_output+0x3a8/0x740
  ip_finish_output2+0x5c0/0xe70
  ip_finish_output+0x4ba/0x680
  ip_output+0x1c1/0x3a0
  xfrm_output_resume+0xc65/0x13d0
  xfrm_output+0x1e4/0x380
  xfrm4_output_finish+0x5c/0x70

Can be fixed if we get skb->len before dst_output().

Fixes: b9959fd3 ("vti: switch to new ip tunnel code")
Fixes: 22e1b23d ("vti6: Support inter address family tunneling.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_KASAN is enabled, the "--param asan-stack=1" causes rather large
stack frames in some functions. This goes unnoticed normally because
CONFIG_FRAME_WARN is disabled with CONFIG_KASAN by default as of commit
3f181b4d ("lib/Kconfig.debug: disable -Wframe-larger-than warnings with
KASAN=y").

The kernelci.org build bot however has the warning enabled and that led
me to investigate it a little further, as every build produces these warnings:

net/wireless/nl80211.c:4389:1: warning: the frame size of 2240 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1895:1: warning: the frame size of 3776 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1410:1: warning: the frame size of 2208 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/bridge/br_netlink.c:1282:1: warning: the frame size of 2544 bytes is larger than 2048 bytes [-Wframe-larger-than=]

Most of this problem is now solved in gcc-8, which can consolidate
the stack slots for the inline function arguments. On older compilers
we can add a workaround by declaring a local variable in each function
to pass the inline function argument.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:

drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]

gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length.  Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field.  This is why the error was not detected earlier.

Fixes: b9b17deb ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
l2tp: fix some races in session deletion

L2TP provides several interfaces for deleting sessions. Using two of
them concurrently can lead to use-after-free bugs.

Patch #2 uses a flag to prevent double removal of L2TP sessions.
Patch #1 fixes a bug found in the way. Fixing this bug is also
necessary for patch #2 to handle all cases.

This issue is similar to the tunnel deletion bug being worked on by
Sabrina: https://patchwork.ozlabs.org/patch/814173/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>