- 14 Dec, 2005 39 commits
-
-
James.Smart@Emulex.Com authored
Signed-off-by:James Bottomley <James.Bottomley@SteelEye.com>
-
James.Smart@Emulex.Com authored
Signed-off-by:
James Smart <James.Smart@emulex.com> Signed-off-by:
-
James.Smart@Emulex.Com authored
- Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by:
-
James.Smart@Emulex.Com authored
Signed-off-by:
-
James.Smart@Emulex.Com authored
Signed-off-by:
-
James.Smart@Emulex.Com authored
- Release task management command before counting outstanding commands. TMF was being erroneously counted as an active outstanding command. - Serialize EH calls and block requests when EH function is running. Signed-off-by:
-
James.Smart@Emulex.Com authored
Remove locking wrappers around error handlers. Wrappers were added in early 2.6.13 api change Signed-off-by:
-
James.Smart@Emulex.Com authored
- Remove unnecessary scsi_block_requests calls on rport deletes. This was deadlocking the sdev removals as they wanted to flush commands. - No longer block requests when adding the remote port (to block discovery). Instead, register, then change port role. Maps to Qlogic behavior, and closer to the register-node-upon-first-ELS behavior. Signed-off-by:
-
James.Smart@Emulex.Com authored
Cause: Link bounces were causing discovery ELS's to be killed. Driver was not properly flushing ELS commands upon the subsequent link bounces. Thus, processing of ELS post link bounce erroneously assumed discovery failure and device loss. Signed-off-by:
-
James.Smart@Emulex.Com authored
Signed-off-by:
-
James.Smart@Emulex.Com authored
Miscellaneous Cleanups: - Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep. - Convert simple printk to an lpfc_printf_log in queuecommand. - Modify lpfc_abort_handler message 0749 to display more accurate text and data. - Minor style cleanup: fix 3 long lines in lpfc_hw.h Signed-off-by:
-
James Bottomley authored
Signed-off-by: -
James Bottomley authored
Make the vendor, model and rev fields in scsi_device pointers to const and update a few prototypes of functions using them. Signed-off-by: -
Mike Christie authored
From Wang Zhenyu: check header digest for cmd and mgmt tasks Signed-off-by:
Wang Zhenyu <zhenyu.z.wang@intel.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
Alex Aizman <itn780@yahoo.com> Signed-off-by:
Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by:
-
Mike Christie authored
Signed-off-by:
-
Mike Christie authored
From Wang Zhenyu: High queue depth was a problem for some targets so make queue_depth adjustable From Mike Christie Make default queue_depth a little lower Signed-off-by:
-
Mike Christie authored
From Wang Zhenyu: data digest fix (the bug caused data corruption w/Wasabi StorageBuilder target) Signed-off-by:
-
Mike Christie authored
from Wang Zhenyu: Must check SCSI CMD and R2T response according to the spec Signed-off-by:
-
Mike Christie authored
From tomof@acm.org: There is one more issue about Equallogic systems. They send re-direction info with FIN. I think that the kernel module needs to let iscsid to read data from the socket before killing it. Signed-off-by:
-
Mike Christie authored
Must check only valid opcode bits. Signed-off-by:
-
Matthew Wilcox authored
Update version number to 2.2.2 Signed-off-by:
Matthew Wilcox <matthew@wil.cx> Signed-off-by:
-
Matthew Wilcox authored
Rather than print a list of targets at driver init time, print each disabled target as we attempt to scan it. Signed-off-by:
-
Matthew Wilcox authored
The NVRAM for both Tekram and Symbios boards allows the user to set the speed and width for individual targets. I took that code out in March 2004 when we introduced Domain Validation, but it seems there's still a legitimate need for it in some configurations. Signed-off-by:
-
Matthew Wilcox authored
sym_show_msg was almost a duplicate of scsi_print_msg, except not as featureful. So use the common code instead. Signed-off-by:
-
Matthew Wilcox authored
Now that this constant has been added to dma-mapping.h, we don't need our own definition Signed-off-by:
-
Matthew Wilcox authored
The upper layer doesn't send these down since 2.4.x (or 2.6 in practice), so no need to handle it. Inline sym_setup_data_pointers into its only caller so we can fail gracefully in the case we'd get one neverless. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Matthew Wilcox authored
Allocate the lcb in slave_alloc and free it in slave_destroy. This allows us to remove all the code that checks to see if it's already been allocated. From: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Matthew Wilcox authored
The SYM_OPT_SNIFF_INQUIRY define is never set any more, and the sym_sniff_inquiry() function doesn't exist From: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Matthew Wilcox authored
Remove FreeBSD ifdefs from sym2 driver Signed-off-by:
-
Matthew Wilcox authored
Update to mention scsi_scan_host() Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
Andrew Vasquez authored
Transition driver to exclusively use the request_firmware() interfaces to retrieve firmware-blobs from user-space. This will be the default behaviour going forward until the embedded firmware-binary images are removed from the upstream kernel. Upon request, the driver caches the firmware image until the driver is unloaded. NOTE: The option is present to allow the user to continue to use the firmware-loader modules, but, should be considered deprecated. Signed-off-by:
-
Jens Axboe authored
Check the asc and ascq for being "invalid command opcode" as well. Signed-off-by: -
Matthew Wilcox authored
None of the other domain validation messages have a trailing full stop, so I don't see why this one should. Signed-off-by:
-
Arjan van de Ven authored
patch below marks a few scsi core datastructures as const, so that they end up in the .rodata section and don't cacheline share with things that get dirtied Signed-off-by:
Arjan van de Ven <arjan@infradead.org> Signed-off-by:
-
brking@us.ibm.com authored
When kexec booting a kernel when the previous kernel did not call ipr's shutdown method, the ipr adapter does not get properly initialized, which can result in the ipr adapter completing commands issued by the previous kernel. Fix ipr to detect this scenario by reading the adapter's interrupt mask register and the microprocessor interrupt register. If the interrupt mask register indicates that interrupts are enabled or the reset alert bit is set when the card is probed, this means the card is in an unknown state and we hard reset the card. Signed-off-by:
Brian King <brking@us.ibm.com> Signed-off-by:
-
Ju, Seokmann authored
Signed-off-by: -
Ju, Seokmann authored
This patch fixes - PCI ID overlap issue - node name changed to 'megaraid_legacy' I hope this patch addresses concerns brought by Daniel Drake. Signed-off by: Seokmann Ju <seokmann.ju@enginio.com> Signed-off-by:
-
- 13 Dec, 2005 1 commit
-
-
Antonino A. Daplas authored
The drawing function cfbfillrect does not work correctly when access is not unsigned-long aligned. It manifests as extra lines of pixels that are not complete drawn. Reversing the shift operator solves the problem, so I would presume that this bug would manifest only on little endian machines. The function cfbcopyarea may also have this bug. Aligned access should present no problems. Signed-off-by:
Antonino Daplas <adaplas@pol.net> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
