Since commit edc6afc5 ("[PATCH] tty: switch to ktermios and new
framework") arbitrary baud rates can be requested using BOTHER and input
rates can be requested using the termios CIBAUD bits (CBAUD shifted
IBSHIFT bits).

This functionality has been conditionally compiled depending on whether
an architecture defines BOTHER and IBSHIFT respectively, but would in
fact fail to compile unless both symbols were defined due to cross
dependencies.

Relax the IBSHIFT => BOTHER dependency so that an architecture could
theoretically support CIBAUD without the Linux-specific BOTHER, while
hopefully making the current conditional-compilation directives a bit
less confusing.

Note that the long-term goal is still to have all architectures support
both features, so an alternative could just be to have the lot depend on
BOTHER.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the termios CIBAUD bits are left unset (i.e. B0), we use the same
output and input speed and should leave CIBAUD unchanged.

When the user requests a rate using BOTHER and c_ospeed which the driver
cannot set exactly, the driver can report back the actual baud rate
using tty_termios_encode_baud_rate(). If this rate is close enough to a
standard rate however, we could end up setting CIBAUD to a Bfoo value
despite the user having left it unset.

This in turn could lead to an unexpected input rate being set on
subsequent termios updates.

Fix this by using a zero tolerance value also for the input rate when
CIBAUD is clear so that the matching logic works as expected.

Fixes: 78137e3b ("[PATCH] tty: improve encode_baud_rate logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to clear the CIBAUD bits before OR-ing the new mask when
encoding the termios input baud rate.

This could otherwise lead to an incorrect input rate being reported back
and incidentally set on subsequent termios updates.

Fixes: edc6afc5 ("[PATCH] tty: switch to ktermios and new framework")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for flow control functionality in the GENI serial driver
and also support for non-console higher baud rate(upto 4Mbps) usecases.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Mohammed Khajapasha <mkhaja@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't dispose IRQ mapping before it has been created.

Fixes: aa959474 ("serial: 8250_of: Add IO space support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add R7S9210 (RZ/A2) support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for a "RZ_SCIFA" which is different than a traditional
SCIFA. It looks like a normal SCIF with FIFO data, but with a
compressed address space. Also, the break out of interrupts
are different then traditinal SCIF: ERI/BRI, RXI, TXI, TEI, DRI.
The R7S9210 (RZ/A2) contains this type of SCIF.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to open up the required power gate before any operation can be
effectively performed over the serial bus between CPU and serdev, it's
clearly essential to add common attach functions for PM domains to serdev
at the probe phase.

Similarly, the relevant dettach function for the PM domains should be
properly and reversely added at the remove phase.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pointer ch is being assigned but is never used hence it is redundant
and can be removed.

Cleans up clang warning:
warning: variable 'ch' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We have reports of the following crash:

    PID: 7 TASK: ffff88085c6d61c0 CPU: 1 COMMAND: "kworker/u25:0"
    #0 [ffff88085c6db710] machine_kexec at ffffffff81046239
    #1 [ffff88085c6db760] crash_kexec at ffffffff810fc248
    #2 [ffff88085c6db830] oops_end at ffffffff81008ae7
    #3 [ffff88085c6db860] no_context at ffffffff81050b8f
    #4 [ffff88085c6db8b0] __bad_area_nosemaphore at ffffffff81050d75
    #5 [ffff88085c6db900] bad_area_nosemaphore at ffffffff81050e83
    #6 [ffff88085c6db910] __do_page_fault at ffffffff8105132e
    #7 [ffff88085c6db9b0] do_page_fault at ffffffff8105152c
    #8 [ffff88085c6db9c0] page_fault at ffffffff81a3f122
    [exception RIP: uart_put_char+149]
    RIP: ffffffff814b67b5 RSP: ffff88085c6dba78 RFLAGS: 00010006
    RAX: 0000000000000292 RBX: ffffffff827c5120 RCX: 0000000000000081
    RDX: 0000000000000000 RSI: 000000000000005f RDI: ffffffff827c5120
    RBP: ffff88085c6dba98 R8: 000000000000012c R9: ffffffff822ea320
    R10: ffff88085fe4db04 R11: 0000000000000001 R12: ffff881059f9c000
    R13: 0000000000000001 R14: 000000000000005f R15: 0000000000000fba
    ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
    #9 [ffff88085c6dbaa0] tty_put_char at ffffffff81497544
    #10 [ffff88085c6dbac0] do_output_char at ffffffff8149c91c
    #11 [ffff88085c6dbae0] __process_echoes at ffffffff8149cb8b
    #12 [ffff88085c6dbb30] commit_echoes at ffffffff8149cdc2
    #13 [ffff88085c6dbb60] n_tty_receive_buf_fast at ffffffff8149e49b
    #14 [ffff88085c6dbbc0] __receive_buf at ffffffff8149ef5a
    #15 [ffff88085c6dbc20] n_tty_receive_buf_common at ffffffff8149f016
    #16 [ffff88085c6dbca0] n_tty_receive_buf2 at ffffffff8149f194
    #17 [ffff88085c6dbcb0] flush_to_ldisc at ffffffff814a238a
    #18 [ffff88085c6dbd50] process_one_work at ffffffff81090be2
    #19 [ffff88085c6dbe20] worker_thread at ffffffff81091b4d
    #20 [ffff88085c6dbeb0] kthread at ffffffff81096384
    #21 [ffff88085c6dbf50] ret_from_fork at ffffffff81a3d69f​

after slogging through some dissasembly:

ffffffff814b6720 <uart_put_char>:
ffffffff814b6720:	55                   	push   %rbp
ffffffff814b6721:	48 89 e5             	mov    %rsp,%rbp
ffffffff814b6724:	48 83 ec 20          	sub    $0x20,%rsp
ffffffff814b6728:	48 89 1c 24          	mov    %rbx,(%rsp)
ffffffff814b672c:	4c 89 64 24 08       	mov    %r12,0x8(%rsp)
ffffffff814b6731:	4c 89 6c 24 10       	mov    %r13,0x10(%rsp)
ffffffff814b6736:	4c 89 74 24 18       	mov    %r14,0x18(%rsp)
ffffffff814b673b:	e8 b0 8e 58 00       	callq  ffffffff81a3f5f0 <mcount>
ffffffff814b6740:	4c 8b a7 88 02 00 00 	mov    0x288(%rdi),%r12
ffffffff814b6747:	45 31 ed             	xor    %r13d,%r13d
ffffffff814b674a:	41 89 f6             	mov    %esi,%r14d
ffffffff814b674d:	49 83 bc 24 70 01 00 	cmpq   $0x0,0x170(%r12)
ffffffff814b6754:	00 00
ffffffff814b6756:	49 8b 9c 24 80 01 00 	mov    0x180(%r12),%rbx
ffffffff814b675d:	00
ffffffff814b675e:	74 2f                	je     ffffffff814b678f <uart_put_char+0x6f>
ffffffff814b6760:	48 89 df             	mov    %rbx,%rdi
ffffffff814b6763:	e8 a8 67 58 00       	callq  ffffffff81a3cf10 <_raw_spin_lock_irqsave>
ffffffff814b6768:	41 8b 8c 24 78 01 00 	mov    0x178(%r12),%ecx
ffffffff814b676f:	00
ffffffff814b6770:	89 ca                	mov    %ecx,%edx
ffffffff814b6772:	f7 d2                	not    %edx
ffffffff814b6774:	41 03 94 24 7c 01 00 	add    0x17c(%r12),%edx
ffffffff814b677b:	00
ffffffff814b677c:	81 e2 ff 0f 00 00    	and    $0xfff,%edx
ffffffff814b6782:	75 23                	jne    ffffffff814b67a7 <uart_put_char+0x87>
ffffffff814b6784:	48 89 c6             	mov    %rax,%rsi
ffffffff814b6787:	48 89 df             	mov    %rbx,%rdi
ffffffff814b678a:	e8 e1 64 58 00       	callq  ffffffff81a3cc70 <_raw_spin_unlock_irqrestore>
ffffffff814b678f:	44 89 e8             	mov    %r13d,%eax
ffffffff814b6792:	48 8b 1c 24          	mov    (%rsp),%rbx
ffffffff814b6796:	4c 8b 64 24 08       	mov    0x8(%rsp),%r12
ffffffff814b679b:	4c 8b 6c 24 10       	mov    0x10(%rsp),%r13
ffffffff814b67a0:	4c 8b 74 24 18       	mov    0x18(%rsp),%r14
ffffffff814b67a5:	c9                   	leaveq
ffffffff814b67a6:	c3                   	retq
ffffffff814b67a7:	49 8b 94 24 70 01 00 	mov    0x170(%r12),%rdx
ffffffff814b67ae:	00
ffffffff814b67af:	48 63 c9             	movslq %ecx,%rcx
ffffffff814b67b2:	41 b5 01             	mov    $0x1,%r13b
ffffffff814b67b5:	44 88 34 0a          	mov    %r14b,(%rdx,%rcx,1)
ffffffff814b67b9:	41 8b 94 24 78 01 00 	mov    0x178(%r12),%edx
ffffffff814b67c0:	00
ffffffff814b67c1:	83 c2 01             	add    $0x1,%edx
ffffffff814b67c4:	81 e2 ff 0f 00 00    	and    $0xfff,%edx
ffffffff814b67ca:	41 89 94 24 78 01 00 	mov    %edx,0x178(%r12)
ffffffff814b67d1:	00
ffffffff814b67d2:	eb b0                	jmp    ffffffff814b6784 <uart_put_char+0x64>
ffffffff814b67d4:	66 66 66 2e 0f 1f 84 	data32 data32 nopw %cs:0x0(%rax,%rax,1)
ffffffff814b67db:	00 00 00 00 00

for our build, this is crashing at:

    circ->buf[circ->head] = c;

Looking in uart_port_startup(), it seems that circ->buf (state->xmit.buf)
protected by the "per-port mutex", which based on uart_port_check() is
state->port.mutex. Indeed, the lock acquired in uart_put_char() is
uport->lock, i.e. not the same lock.

Anyway, since the lock is not acquired, if uart_shutdown() is called, the
last chunk of that function may release state->xmit.buf before its assigned
to null, and cause the race above.

To fix it, let's lock uport->lock when allocating/deallocating
state->xmit.buf in addition to the per-port mutex.

v2: switch to locking uport->lock on allocation/deallocation instead of
    locking the per-port mutex in uart_put_char. Note that since
    uport->lock is a spin lock, we have to switch the allocation to
    GFP_ATOMIC.
v3: move the allocation outside the lock, so we can switch back to
    GFP_KERNEL
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.

Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add these two hooks so that they can be overridden with driver specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This completes dead keys definitions for internationalization
completeness on the console.  The representatives have been chosen
coherently with libx11 compose sequences, which avoid symetry conflicts
(e.g. there is U with caron, but no c with breve).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The WCH CH382L PCIe adapter has 1 parallel port but unlike the similar
WCH CH328 adapter there are no serial ports connected to it.  Enable
this adapter with the addition of the appropriate PCIe IDs and board
support config.

PCIe device ID 1c00:3050:

02:00.0 Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850])
	Subsystem: Device 1c00:3050
	Flags: fast devsel, IRQ 16
	I/O ports at 2000 [size=256]
	Memory at d0000000 (32-bit, prefetchable) [size=32K]
	I/O ports at 2100 [size=4]
	Expansion ROM at b0200000 [disabled] [size=32K]
	Capabilities: [60] Power Management version 3
	Capabilities: [68] MSI: Enable- Count=1/32 Maskable+ 64bit+
	Capabilities: [80] Express Legacy Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Kernel driver in use: parport_pc
	Kernel modules: parport_pc, parport_serial
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are several extended (in comparison to the traditional 16550)
registers are present in Synopsys DesignWare UART. All of them
are 32-bit ones.

Introduce helpers to simplify access to them and convert existing users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update the dt-binding documentation of sysirq for mt6765
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add documentation for mt6765 uart dt-bindings
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update binding document for mt6765 reference board
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Align serial8250_get_divisor() with serial8250_set_divisor() to accept
uart_port pointer as the first parameter. No functionality changes.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As of commit b36f09c3 ("dmaengine: Add transfer termination
synchronization support"), dmaengine_terminate_all() is deprecated.

Replace calls to dmaengine_terminate_all() in DMA release code by calls
to dmaengine_terminate_sync(), as the latter waits until all running
completion callbacks have finished.

Replace calls to dmaengine_terminate_all() in DMA failure paths by calls
to dmaengine_terminate_async(), as these are usually done in atomic
context.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The transmit DMA workqueue is never stopped, hence the work function may
be called after the port has been shut down.

Fix this race condition by cancelling queued work, if any, before DMA
release.  Don't initialize the work if DMA initialization failed, as it
won't be used anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the sh-sci driver detects an issue with DMA during operation, it
falls backs to PIO, and releases all DMA resources.

As releasing DMA resources immediately has no advantages, but
complicates the code, and is susceptible to races, it is better to
postpone this to port shutdown.

This allows to remove the locking from sci_rx_dma_release() and
sci_tx_dma_release(), but requires keeping a copy of the DMA channel
pointers for release during port shutdown.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The RX FIFO timer may be armed when the port is shut down, hence the
timer function may still be called afterwards.

Fix this race condition by deleting the timer during port shutdown.

Fixes: 03940376 ("serial: sh-sci: SCIFA/B RX FIFO software timeout")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want ths tty core changes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull btrfs fixes from David Sterba:
 "We have a few regression fixes for qgroup rescan status tracking and
  the vm_fault_t conversion that mixed up the error values"

* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix mount failure when qgroup rescan is in progress
  Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
  btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf

Pull vfs fix from Al Viro:
 "Followup to procfs-seq_file series this window"

This fixes a memory leak by making sure that proc seq files release any
private data on close.  The 'proc_seq_open' has to be properly paired
with 'proc_seq_release' that releases the extra private data.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  proc: add proc_seq_release

Pull staging/IIO fixes from Greg KH:
 "Here are a few small staging and IIO driver fixes for 4.18-rc3.

  Nothing major or big, all just fixes for reported problems since
  4.18-rc1. All of these have been in linux-next this week with no
  reported problems"

* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: android: ion: Return an ERR_PTR in ion_map_kernel
  staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
  iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
  iio: buffer: fix the function signature to match implementation
  iio: mma8452: Fix ignoring MMA8452_INT_DRDY
  iio: tsl2x7x/tsl2772: avoid potential division by zero
  iio: pressure: bmp280: fix relative humidity unit

Pull tty/serial fixes from Greg KH:
 "Here are five fixes for the tty core and some serial drivers.

  The tty core ones fix some security and other issues reported by the
  syzbot that I have taken too long in responding to (sorry Tetsuo!).

  The 8350 serial driver fix resolves an issue of devices that used to
  work properly stopping working as they shouldn't have been added to a
  blacklist.

  All of these have been in linux-next for a few days with no reported
  issues"

* tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt: prevent leaking uninitialized data to userspace via /dev/vcs*
  serdev: fix memleak on module unload
  serial: 8250_pci: Remove stalled entries in blacklist
  n_tty: Access echo_* variables carefully.
  n_tty: Fix stall at n_tty_receive_char_special().

Pull USB fixes from Greg KH:
 "Here is a number of USB gadget and other driver fixes for 4.18-rc3.

  There's a bunch of them here, most of them being gadget driver and
  xhci host controller fixes for reported issues (as normal), but there
  are also some new device ids, and some fixes for the typec code.

  There is an acpi core patch in here that was acked by the acpi
  maintainer as it is needed for the typec fixes in order to properly
  solve a problem in that driver.

  All of these have been in linux-next this week with no reported
  issues"

* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: chipidea: host: fix disconnection detect issue
  usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
  typec: tcpm: Fix a msecs vs jiffies bug
  NFC: pn533: Fix wrong GFP flag usage
  usb: cdc_acm: Add quirk for Uniden UBC125 scanner
  staging/typec: fix tcpci_rt1711h build errors
  usb: typec: ucsi: Fix for incorrect status data issue
  usb: typec: ucsi: acpi: Workaround for cache mode issue
  acpi: Add helper for deactivating memory region
  usb: xhci: increase CRS timeout value
  usb: xhci: tegra: fix runtime PM error handling
  usb: xhci: remove the code build warning
  xhci: Fix kernel oops in trace_xhci_free_virt_device
  xhci: Fix perceived dead host due to runtime suspend race with event handler
  dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
  usb: gadget: dwc2: fix memory leak in gadget_init()
  usb: gadget: composite: fix delayed_status race condition when set_interface
  usb: dwc2: fix isoc split in transfer with no data
  usb: dwc2: alloc dma aligned buffer for isoc split in
  usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
  ...

Pull dma mapping fixlet from Christoph Hellwig:
 "Add a missing export required by riscv and unicore"

* tag 'dma-mapping-4.18-2' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: export swiotlb_dma_ops

Pull parisc fixes and cleanups from Helge Deller:
 "Nothing exiting in this patchset, just

   - small cleanups of header files

   - default to 4 CPUs when building a SMP kernel

   - mark 16kB and 64kB page sizes broken

   - addition of the new io_pgetevents syscall"

* 'parisc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Build kernel without -ffunction-sections
  parisc: Reduce debug output in unwind code
  parisc: Wire up io_pgetevents syscall
  parisc: Default to 4 SMP CPUs
  parisc: Convert printk(KERN_LEVEL) to pr_lvl()
  parisc: Mark 16kB and 64kB page sizes BROKEN
  parisc: Drop struct sigaction from not exported header file

Pull ARM SoC fixes from Olof Johansson:
 "A smaller batch for the end of the week (let's see if I can keep the
  weekly cadence going for once).

  All medium-grade fixes here, nothing worrisome:

   - Fixes for some fairly old bugs around SD card write-protect
     detection and GPIO interrupt assignments on Davinci.

   - Wifi module suspend fix for Hikey.

   - Minor DT tweaks to fix inaccuracies for Amlogic platforms, one
     of which solves booting with third-party u-boot"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: hikey960: Define wl1837 power capabilities
  arm64: dts: hikey: Define wl1835 power capabilities
  ARM64: dts: meson-gxl: fix Mali GPU compatible string
  ARM64: dts: meson-axg: fix ethernet stability issue
  ARM64: dts: meson-gx: fix ATF reserved memory region
  ARM64: dts: meson-gxl-s905x-p212: Add phy-supply for usb0
  ARM64: dts: meson: fix register ranges for SD/eMMC
  ARM64: dts: meson: disable sd-uhs modes on the libretech-cc
  ARM: dts: da850: Fix interrups property for gpio
  ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD

Merge tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - introduce __diag_* macros and suppress -Wattribute-alias warnings
   from GCC 8

 - fix stack protector test script for x86_64

 - fix line number handling in Kconfig

 - document that '#' starts a comment in Kconfig

 - handle P_SYMBOL property in dump debugging of Kconfig

 - correct help message of LD_DEAD_CODE_DATA_ELIMINATION

 - fix occasional segmentation faults in Kconfig

* tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: loop boundary condition fix
  kbuild: reword help of LD_DEAD_CODE_DATA_ELIMINATION
  kconfig: handle P_SYMBOL in print_symbol()
  kconfig: document Kconfig source file comments
  kconfig: fix line numbers for if-entries in menu tree
  stack-protector: Fix test with 32-bit userland and CONFIG_64BIT=y
  powerpc: Remove -Wattribute-alias pragmas
  disable -Wattribute-alias warning for SYSCALL_DEFINEx()
  kbuild: add macro for controlling warnings to linux/compiler.h

Pull x86 fixes from Ingo Molnar:
 "The biggest diffstat comes from self-test updates, plus there's entry
  code fixes, 5-level paging related fixes, console debug output fixes,
  and misc fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Clean up the printk()s in show_fault_oops()
  x86/mm: Drop unneeded __always_inline for p4d page table helpers
  x86/efi: Fix efi_call_phys_epilog() with CONFIG_X86_5LEVEL=y
  selftests/x86/sigreturn: Do minor cleanups
  selftests/x86/sigreturn/64: Fix spurious failures on AMD CPUs
  x86/entry/64/compat: Fix "x86/entry/64/compat: Preserve r8-r11 in int $0x80"
  x86/mm: Don't free P4D table when it is folded at runtime
  x86/entry/32: Add explicit 'l' instruction suffix
  x86/mm: Get rid of KERN_CONT in show_fault_oops()

Pull perf fixes from Ingo Molnar:
 "Tooling fixes mostly, plus a build warning fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  perf/core: Move inline keyword at the beginning of declaration
  tools/headers: Pick up latest kernel ABIs
  perf tools: Fix crash caused by accessing feat_ops[HEADER_LAST_FEATURE]
  perf script: Fix crash because of missing evsel->priv
  perf script: Add missing output fields in a hint
  perf bench: Fix numa report output code
  perf stat: Remove duplicate event counting
  perf alias: Rebuild alias expression string to make it comparable
  perf alias: Remove trailing newline when reading sysfs files
  perf tools: Fix a clang 7.0 compilation error
  tools include uapi: Synchronize bpf.h with the kernel
  tools include uapi: Update if_link.h to pick IFLA_{BRPORT_ISOLATED,VXLAN_TTL_INHERIT}
  tools include powerpc: Update arch/powerpc/include/uapi/asm/unistd.h copy to get 'rseq' syscall
  perf tools: Update x86's syscall_64.tbl, adding 'io_pgetevents' and 'rseq'
  tools headers uapi: Synchronize drm/drm.h
  perf intel-pt: Fix packet decoding of CYC packets
  perf tests: Add valid callback for parse-events test
  perf tests: Add event parsing error handling to parse events test
  perf report powerpc: Fix crash if callchain is empty
  perf test session topology: Fix test on s390
  ...

Pull selinux fix from Paul Moore:
 "One fairly straightforward patch to fix a longstanding issue where a
  process could stall while accessing files in selinuxfs and block
  everyone else due to a held mutex.

  The patch passes all our tests and looks to apply cleanly to your
  current tree"

* tag 'selinux-pr-20180629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: move user accesses in selinuxfs out of locked regions

Pull block fixes from Jens Axboe:
 "Small set of fixes for this series. Mostly just minor fixes, the only
  oddball in here is the sg change.

  The sg change came out of the stall fix for NVMe, where we added a
  mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
  sort-of ruins that, since we'd need to account for that. That's
  actually a generic problem, since lots of drivers need to allocate SG
  lists. So this just removes support for CONFIG_SG_DEBUG, which I added
  back in 2007 and to my knowledge it was never useful.

  Anyway, outside of that, this pull contains:

   - clone of request with special payload fix (Bart)

   - drbd discard handling fix (Bart)

   - SATA blk-mq stall fix (me)

   - chunk size fix (Keith)

   - double free nvme rdma fix (Sagi)"

* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
  sg: remove ->sg_magic member
  drbd: Fix drbd_request_prepare() discard handling
  blk-mq: don't queue more if we get a busy return
  block: Fix cloning of requests with a special payload
  nvme-rdma: fix possible double free of controller async event buffer
  block: Fix transfer when chunk sectors exceeds max