- 07 Jan, 2011 22 commits
-
-
Alex Deucher authored
Signed-off-by:
Alex Deucher <alexdeucher@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
NI chips no longer load the MC ucode in the asic_init sequence so the asic comes up in a basic mode with low engine/memory clocks and a voltage. Once the MC ucode is loaded by the driver the card can be programmed to it's proper default clocks and voltage. As such the default clocks in the firmware info table as the post clocks, not the default running clocks. Track the default post clocks and default running clocks separately to handle this. Signed-off-by:
-
Alex Deucher authored
Same as Cypress. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Some systems disable the vbios on secondary cards or cards that have been posted. This code re-enabled the vbios so the driver can load it. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Needed to tell which DIG encoders are HBR2 capable for DP 1.2. Signed-off-by:
-
Alex Deucher authored
The DVOOutputControl table was removed for DCE5. DVOEncoderControl now handles everything. Signed-off-by:
-
Alex Deucher authored
The DAC1OutputControl table was removed for DCE5. DAC1EncoderControl now handles everything. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
only fusion asics are dce4.1 Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
- 06 Jan, 2011 5 commits
-
-
Alex Deucher authored
Reported-by:
屋国遥 <hyagni@gmail.com> Signed-off-by:
-
Tejun Heo authored
With cmwq, there's no reason for radeon to use a dedicated workqueue. Drop dev_priv->wq and use system_wq instead. Because radeon_driver_irq_uninstall_kms() may be called from unsleepable context, the work items can't be flushed from there. Instead, init and flush from radeon_irq_kms_init/fini(). While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work. Always initialize and sync cancel instead of being unnecessarily smart about it. Signed-off-by:
Tejun Heo <tj@kernel.org> Acked-by:
-
Dave Airlie authored
Signed-off-by: -
Marek Olšák authored
The CMASK RAM is for colorbuffer compression (used in conjunction with MSAA). Only one user (filp) can access it. The CMASK RAM access is managed in the same way as Hyper-Z, but there is a separate ioctl, because an app that uses MSAA does not necessarily have to use zbuffering. Signed-off-by:
Marek Olšák <maraeo@gmail.com> Signed-off-by:
-
Alex Deucher authored
Acer laptop (TravelMate 5730G) has an HDMI connector on the laptop and a DVI connector on the docking station and both share the same encoder, hpd pin, and ddc line. The bios connector table reflects this and is technically correct, however, we drop the DVI connector here since xrandr has no concept of encoders (only crtcs and connectors) and will try and drive both connectors with different crtcs which isn't possible on the hardware side and leaves no crtcs for LVDS or VGA. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=32732Signed-off-by:
-
- 05 Jan, 2011 8 commits
-
-
Dave Airlie authored
stage 1: turn card on, switch boot vga pointer. stage 2: switch fbs, switch mux and power off old card. Signed-off-by: -
Dave Airlie authored
We need to track the state of the switch in drivers, so that after s/r we don't resume the card we've explicitly switched off before. Also don't allow a userspace open to occur if we've switched the gpu off. Signed-off-by: -
Dave Airlie authored
This adds a hook after the mux is switched for the driver to reprobe the connected outputs. Signed-off-by: -
Dave Airlie authored
This improves the IGD/DIS picking using firstly if Intel, then if the bus is bus 0. There may be a correct way to do this, but I've no idea what it is. Signed-off-by: -
Dave Airlie authored
this just adds the callback on the delayed switch mechanism. Signed-off-by: -
Dave Airlie authored
This allows the mux to be switched from userspace using MIGD/MDIS command to the switch. Signed-off-by: -
Dave Airlie authored
At least on the nvidia mux the power switch seems to be executed by the ACPI PS0/PS3 methods so need to do it explicitly. Signed-off-by: -
Dave Airlie authored
We really want to see this so we can confirm that we pick the right one. Signed-off-by:
-
- 04 Jan, 2011 5 commits
-
-
Alex Deucher authored
Now that soft reset works, we can add this. Signed-off-by:
-
Dave Airlie authored
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-arm: ARM: pxa: fix page table corruption on resume ARM: it8152: add IT8152_LAST_IRQ definition to fix build error ARM: pxa: PXA_ESERIES depends on FB_W100. ARM: 6605/1: Add missing include "asm/memory.h" ARM: 6540/1: Stop irqsoff trace on return to user ARM: 6537/1: update Nomadik, U300 and Ux500 maintainers ARM: 6536/1: Add missing SZ_{32,64,128} ARM: fix cache-feroceon-l2 after stack based kmap_atomic() ARM: fix cache-xsc3l2 after stack based kmap_atomic() ARM: get rid of kmap_high_l1_vipt() ARM: smp: avoid incrementing mm_users on CPU startup ARM: pxa: PXA_ESERIES depends on FB_W100. -
Andrew Morton authored
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=25702Reported-by:
Martin Ettl <ettl.martin@gmx.de> Cc: David Howells <dhowells@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Mimi Zohar authored
If security_filter_rule_init() doesn't return a rule, then not everything is as fine as the return code implies. This bug only occurs when the LSM (eg. SELinux) is disabled at runtime. Adding an empty LSM rule causes ima_match_rules() to always succeed, ignoring any remaining rules. default IMA TCB policy: # PROC_SUPER_MAGIC dont_measure fsmagic=0x9fa0 # SYSFS_MAGIC dont_measure fsmagic=0x62656572 # DEBUGFS_MAGIC dont_measure fsmagic=0x64626720 # TMPFS_MAGIC dont_measure fsmagic=0x01021994 # SECURITYFS_MAGIC dont_measure fsmagic=0x73636673 < LSM specific rule > dont_measure obj_type=var_log_t measure func=BPRM_CHECK measure func=FILE_MMAP mask=MAY_EXEC measure func=FILE_CHECK mask=MAY_READ uid=0 Thus without the patch, with the boot parameters 'tcb selinux=0', adding the above 'dont_measure obj_type=var_log_t' rule to the default IMA TCB measurement policy, would result in nothing being measured. The patch prevents the default TCB policy from being replaced. Signed-off-by:
Mimi Zohar <zohar@us.ibm.com> Cc: James Morris <jmorris@namei.org> Acked-by:
Serge Hallyn <serge.hallyn@canonical.com> Cc: David Safford <safford@watson.ibm.com> Cc: <stable@kernel.org> Signed-off-by:
-
