- 28 Mar, 2007 22 commits
-
-
Adrian Bunk authored
-
Takashi Iwai authored
Added the missing device assignment before creating sysfs tree. This caused the insufficient device permissions. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Adrian Bunk <bunk@stusta.de>
-
Takashi Iwai authored
Fix the check of right channel in mixer volume put callback. Signed-off-by:
-
Florin Malita authored
snd_card_file_remove() may free hw->card so we can't dereference hw->card->module after that. Coverity ID 1420. Signed-off-by:
Florin Malita <fmalita@gmail.com> Signed-off-by:
-
Takashi Iwai authored
Fixed a typo in 'PC Speaker Playback Switch' control name. Signed-off-by:
-
Eric Sesterhenn authored
this is about coverity id #100. It seems the if statement is negated, since the else branch calls remove_info() with sflist->currsf as a parameter where it gets dereferenced. Signed-off-by:
Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by:
-
Takashi Iwai authored
Fix the type of PCI revision to char from int and avoid invalid assignment with pointer cast. Signed-off-by:
-
Takashi Iwai authored
Fix the max number of codecs detected by HD-intel (and compatible) controllers. ATI controllers may have up to 4 codecs while ICH up to 3. Now max codecs is defined according to the driver type, either 3 or 4. Currently 4 is set only to ATI chips. Other might need the same change, too. Signed-off-by:
-
Takashi Iwai authored
Some modem codec seem to fail in the initialization, and this stopped loading of the whole module although the audio is OK. Since it's usually a non-fatal issue, the driver tries to proceed to initialize now. Signed-off-by:
-
Clemens Ladisch authored
The C-Media CM6501 chip's descriptors say that altsetting 5 supports 48 kHz, but it actually plays at 96 kHz. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Jaroslav Kysela <perex@suse.cz> Signed-off-by:
-
Amol Lad authored
Signed-off-by:
Amol Lad <amol@verismonetworks.com> Signed-off-by:
-
YOSHIFUJI Hideaki authored
Tetsuo Handa <handat@pm.nttdata.co.jp> told me that connect(2) with TCPv6 socket almost always took a few minutes to return when we did not have any ports available in the range of net.ipv4.ip_local_port_range. The reason was that we used incorrect seed for calculating index of hash when we check established sockets in __inet6_check_established(). Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Guennadi Liakhovetski authored
Signed-off-by:
Guennadi Liakhovetski <gl@dsa-ac.de> Signed-off-by:
-
Patrick McHardy authored
Ingress queueing uses a seperate lock for serializing enqueue operations, but fails to properly protect itself against concurrent changes to the qdisc tree. Use queue_lock for now since the real fix it quite intrusive. Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Patrick McHardy authored
cls_basic doesn't allocate tp->root before it is linked into the active classifier list, resulting in a NULL pointer dereference when packets hit the classifier before its ->change function is called. Reported by Chris Madden <chris@reflexsecurity.com> Signed-off-by:
-
Pete Zaitcev authored
This adds an unusual_devs entry for the Motorola RAZR 3vi. Signed-off-by:
Phil Dibowitz <phil@ipom.com> Signed-off-by:
-
Andrew Nayenko authored
This patch adds an usual_devs entry for the Nokia 6288. Signed-off-by:
-
Dylan Taft authored
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE. I bought this mp3 player that takes SD cards here http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=ASSigned-off-by:
Dylan Taft <d13f00l@gmail.com> Signed-off-by:
-
Luiz Fernando N. Capitulino authored
This patch increases the range for 0x054c:0x002c devices to make the following Sony USB floppy to work: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=002c Rev=20.00 S: Manufacturer=SONY S: Product=USB Floppy C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=04 Prot=00 Driver=usb-storage E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=127ms Signed-off-by:
Marcelo Ricardo Leitner <mrl@mandriva.com> Signed-off-by:
Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Signed-off-by:
-
Patrick McHardy authored
There are multiple problems related to qlen adjustment that can lead to an upper qdisc getting out of sync with the real number of packets queued, leading to endless dequeueing attempts by the upper layer code. All qdiscs must maintain an accurate q.qlen counter. There are basically two groups of operations affecting the qlen: operations that propagate down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the root qdisc and operations only affecting a subtree or single qdisc (change, graft, delete class). Since qlen changes during operations from the second group don't propagate to ancestor qdiscs, their qlen values become desynchronized. This patch adds a function to propagate qlen changes up the qdisc tree, optionally calling a callback function to perform qdisc-internal maintenance when the child qdisc is deactivated, and converts all qdiscs to use this where necessary. Signed-off-by:
-
Nick Piggin authored
madvise(MADV_REMOVE) can go into an infinite loop or cause an oops if the call covers a region from the start of a vma, and extending past that vma. Signed-off-by:
Nick Piggin <npiggin@suse.de> Acked-by:
Hugh Dickins <hugh@veritas.com> Signed-off-by:
-
Russell King authored
A serial card might have been removed when the system is resumed. This results in a suspended port being shut down, which results in the ports shutdown method being called twice in a row. This causes BUGs. Avoid this by tracking the suspended state separately from the initialised state. Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
- 26 Mar, 2007 8 commits
-
-
Stefan Richter authored
Fix NULL pointer dereference on hot ejection of a FireWire card while dv1394 was loaded. http://bugzilla.kernel.org/show_bug.cgi?id=7121Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Akinbou Mita authored
I have seen mdadm oops after successfully unloading md module. This patch privents from unloading md module while mdadm is polling /proc/mdstat. Signed-off-by:
Akinbou Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Andy Isaacson authored
When iterating through an array, one must be careful to test one's index variable rather than another similarly-named variable. The loop will read off the end of conf->disks[] in the following (pathological) case: % dd bs=1 seek=840716287 if=/dev/zero of=d1 count=1 % for i in 2 3 4; do dd if=/dev/zero of=d$i bs=1k count=$(($i+150)); done % ./vmlinux ubd0=root ubd1=d1 ubd2=d2 ubd3=d3 ubd4=d4 # mdadm -C /dev/md0 --level=linear --raid-devices=4 /dev/ubd[1234] adding some printks, I saw this: [42949374.960000] hash_spacing = 821120 [42949374.960000] cnt = 4 [42949374.960000] min_spacing = 801 [42949374.960000] j=0 size=820928 sz=820928 [42949374.960000] i=0 sz=820928 hash_spacing=820928 [42949374.960000] j=1 size=64 sz=64 [42949374.960000] j=2 size=64 sz=128 [42949374.960000] j=3 size=64 sz=192 [42949374.960000] j=4 size=1515870810 sz=1515871002 Signed-off-by: -
Lars Ellenberg authored
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus introducing additional latency. Fixing this in raid1 and raid10 seems to be straightforward enough. For our particular usage case in DRBD, passing this flag improved some initialization time from ~5 minutes to ~5 seconds. Signed-off-by:
Lars Ellenberg <lars@linbit.com> Acked-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Neil Brown authored
If save_raid_disk is >= 0, then the device could be a device that is already in sync that is being re-added. So we need to default this value to -1. Signed-off-by:
-
Neil Brown authored
If a drive is added with HOT_ADD_DISK rather than ADD_NEW_DISK, saved_raid_disk isn't initialised properly, and the drive can be included in the array without a resync. Signed-off-by: -
Alan Stern authored
This patch (as846) adds the IGNORE_RESIDUE flag to the unusual_devs entry for Sony-Ericsson's P990i phone. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Lars Jacob authored
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and T5 to cover the H5 as well. Signed-off-by:
-
- 25 Mar, 2007 10 commits
-
-
Manuel Osdoba authored
Signed-off-by:
-
Pete Zaitcev authored
American Megatrends did something wrong in their floppy emulator. It breaks with both kinds of MODE SENSE which our stack sends. Alan and I tried a few tweaks, and got LUNs sensed right, but US_FL_NO_WP_DETECT is still needed. I set the firmware bracket to 1.00 exactly, in case AMI or Sun fix it with a firmware update. Hey, you never know. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Phil Dibowitz authored
Recently this entry's bcd scope was narrowed so as not to falsly apply to bcd's other than 0x0110. But while it breaks those of a larger bcd, it is still needed for those of a smaller bcd - so this changes the lower bcd limit to 0x0000. Signed-off-by:
-
Alan Stern authored
The existing unusual_devs entry for the UCR-61S2B appears to have too wide a revision range. It matches at least one device that doesn't respond to the initialization sequence. Perhaps the sequence needs to be updated, or perhaps something else can be done. For now, this patch (as764) restricts the range to include only the revision mentioned in the original comment. This resolves (for now!) Bugzilla entry #6950. Signed-off-by:
-
Pete Zaitcev authored
Signed-off-by:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
Phil Dibowitz authored
This combines patches from Alan Stern and Robert Schedel for two "Super Top" drives that need the IGNORE_RESIDUE flag but have different vendor IDs. Signed-off-by:
-
Mikko Honkala authored
When the Nokia E70 Phone is plugged in to the USB port, I get: end_request: I/O error, dev sda, sector 1824527 sd 0:0:0:0: SCSI error: return code = 0x10070000 end_request: I/O error, dev sda, sector 1824535 sd 0:0:0:0: SCSI error: return code = 0x10070000 Signed-off-by:
-
Jaco Kroon authored
The mass storage device from Digitech designed for Flash Cards, as found on (for example) the GNX4 device has issues with residue, similar to the bug report at http://kerneltrap.org/node/6297. This patch adds the faulty storage device to unusual_devs.h, this not only reduces the noise in dmesg but also increases the transfer speeds by a factor of 7x for me (89kB/s -> 637kB/s). T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1210 ProdID=0003 Rev= 1.00 S: Manufacturer=DigiTech HMG S: Product=DigiTech Mass Storage C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms Signed-off-by:
Jaco Kroon <jaco@kroon.co.za> Signed-off-by:
-
Tobias Lorenz authored
Signed-off-by:
-
Phil Dibowitz authored
The protocol in this entry is needed for some versions of the device but not others. This adds the NEED_OVERRIDE flag to prevent it complaining to users who don't need it. Signed-off-by:
-
