hardOrsTypeC: small changes on Signal Track

hardOrsTypeC/Design Rule Check - OrsTypeC.drc

+Protel Design System Design Rule Check
+PCB File : V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\OrsTypeC.PcbDoc
+Date     : 04/05/2023
+Time     : 11:33:00
+
+Processing Rule : Clearance Constraint (Gap=0.35mm) (InNetClass('HighIsolation')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.21mm) (InPolygon),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.2mm) (InNamedPolygon('TOP-GND') OR InNamedPolygon('GND-BOTTOM_PWR1')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.12mm) (All),(IsVia)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.2mm) (InNamedPolygon('L4-+12V-2')OR  InNamedPolygon('L4-+12V')OR InNamedPolygon('BOTTOM+12V')OR InNamedPolygon('BOTTOM+12V-1')OR InNamedPolygon('L6_NoNet2') OR InNamedPolygon('L6_NoNet')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.5mm) (InNetClass('50OhmsL8tol4')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.5mm) (InNamedPolygon('L5_NoNet') OR InNamedPolygon('L6_NoNet') OR InNamedPolygon('L4_NoNet') OR InNamedPolygon('L7_NoNet')OR InNamedPolygon('L3_NoNet')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.1mm) (InNetClass('DiffPairNetClass')),(All)
+Rule Violations :0
+
+Processing Rule : Short-Circuit Constraint (Allowed=No) (All),(All)
+Rule Violations :0
+
+Processing Rule : Un-Routed Net Constraint ( (All) )
+Rule Violations :0
+
+Processing Rule : Power Plane Connect Rule(Direct Connect )(Expansion=0.508mm) (Conductor Width=0.254mm) (Air Gap=0.254mm) (Entries=4) (All)
+Rule Violations :0
+
+Processing Rule : Width Constraint (Min=0.1mm) (Max=10mm) (Preferred=0.254mm) (All)
+Rule Violations :0
+
+Processing Rule : Height Constraint (Min=0mm) (Max=25.4mm) (Prefered=12.7mm) (All)
+Rule Violations :0
+
+Processing Rule : Hole Size Constraint (Min=0.02mm) (Max=3.5mm) (All)
+Rule Violations :0
+
+Processing Rule : Hole To Hole Clearance (Gap=0.25mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Minimum Solder Mask Sliver (Gap=0.05mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Silk To Solder Mask (Clearance=0.2mm) (Disabled)(IsPad),(All)
+Rule Violations :0
+
+Processing Rule : Silk to Silk (Clearance=0.2mm) (Disabled)(All),(All)
+Rule Violations :0
+
+Processing Rule : Net Antennae (Tolerance=0mm) (Disabled)(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.6mm) (InNetClass('50OhmsL1toL2')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.1mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Matched Net Lengths(Tolerance=0.5mm) (InNetClass('POENetClass2'))
+Rule Violations :0
+
+Processing Rule : Matched Net Lengths(Tolerance=0.3mm) (InNetClass('POENetClass1'))
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.21mm) (InNetClass('50OhmsL8toL5')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.12mm) (InNetClass('DiffPairNetClass100Ohms_1_2')),(InPolygon)
+Rule Violations :0
+
+
+Violations Detected : 0
+Time Elapsed        : 00:02:18
\ No newline at end of file

hardOrsTypeC/ORS_TypeC_8Layers.OutJob

@@ -17,11 +17,11 @@ RevisionNamingSchemeGUID=
 [OutputGroup1]
 Name=ORS_TypeC_8Layers.OutJob
 Description=
-TargetOutputMedium=Gerbers
+TargetOutputMedium=Pick And Place
 VariantName=[No Variations]
 VariantScope=0
 CurrentConfigurationName=
-TargetPrinter=Microsoft Print to PDF
+TargetPrinter=PDFCreator
 PrinterOptions=Record=PrinterOptions|Copies=1|Duplex=1|TrueTypeOptions=3|Collate=1|PrintWhat=0
 OutputMedium1=Print Job
 OutputMedium1_Type=Printer
@@ -50,7 +50,7 @@ OutputName1=NC Drill Files
 OutputCategory1=Fabrication
 OutputDocumentPath1=
 OutputVariantName1=
-OutputEnabled1=1
+OutputEnabled1=0
 OutputEnabled1_OutputMedium1=0
 OutputEnabled1_OutputMedium2=0
 OutputEnabled1_OutputMedium3=0
@@ -68,7 +68,7 @@ OutputName2=Gerber Files
 OutputCategory2=Fabrication
 OutputDocumentPath2=
 OutputVariantName2=
-OutputEnabled2=1
+OutputEnabled2=0
 OutputEnabled2_OutputMedium1=0
 OutputEnabled2_OutputMedium2=0
 OutputEnabled2_OutputMedium3=0
@@ -185,7 +185,7 @@ OutputName7=PickPlace-ORSTDDB39
 OutputCategory7=Assembly
 OutputDocumentPath7=
 OutputVariantName7=TDDB39
-OutputEnabled7=0
+OutputEnabled7=1
 OutputEnabled7_OutputMedium1=0
 OutputEnabled7_OutputMedium2=0
 OutputEnabled7_OutputMedium3=0
@@ -365,7 +365,7 @@ OutputName14=PickPlace-ORSTDDB40
 OutputCategory14=Assembly
 OutputDocumentPath14=
 OutputVariantName14=TDDB40
-OutputEnabled14=0
+OutputEnabled14=1
 OutputEnabled14_OutputMedium1=0
 OutputEnabled14_OutputMedium2=0
 OutputEnabled14_OutputMedium3=0
@@ -383,7 +383,7 @@ OutputName15=PickPlace-ORSTDDB41
 OutputCategory15=Assembly
 OutputDocumentPath15=
 OutputVariantName15=TDDB41
-OutputEnabled15=0
+OutputEnabled15=1
 OutputEnabled15_OutputMedium1=0
 OutputEnabled15_OutputMedium2=0
 OutputEnabled15_OutputMedium3=0
@@ -534,7 +534,7 @@ FFmpegPixelFormat3=0
 FFmpegQuality3=80
 WmvVideoCodecName3=Windows Media Video V7
 WmvQuality3=60
-OutputFilePath4=Z:\ors-hardware\hardOrsTypeC\Project Outputs for OrsTypeC\
+OutputFilePath4=V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\Project Outputs for OrsTypeC\
 ReleaseManaged4=1
 OutputBasePath4=Project Outputs for OrsTypeC
 OutputPathMedia4=
@@ -547,7 +547,7 @@ OutputFileNameMulti4=
 UseOutputNameForMulti4=1
 OutputFileNameSpecial4=
 OpenOutput4=0
-OutputFilePath5=Z:\ors-hardware\hardOrs\Project Outputs for Ors\
+OutputFilePath5=V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\Project Outputs for OrsTypeC\
 ReleaseManaged5=1
 OutputBasePath5=Project Outputs for OrsTypeC
 OutputPathMedia5=
@@ -636,7 +636,7 @@ OpenIPCOutput2=0
 EnableReload2=0
 RelativeOutputPath3=C:\NewProj\UmTRX\UmSEL\UmSELv2\Project Outputs\UmTRXv2_RxSel.wmv
 OpenOutputs3=1
-RelativeOutputPath4=Z:\ors-hardware\hardOrsTypeC\Project Outputs for OrsTypeC\
+RelativeOutputPath4=V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\Project Outputs for OrsTypeC\
 OpenOutputs4=0
 AddToProject4=0
 TimestampFolder4=0
@@ -646,7 +646,7 @@ OpenGerberOutput4=1
 OpenNCDrillOutput4=0
 OpenIPCOutput4=0
 EnableReload4=1
-RelativeOutputPath5=Z:\ors-hardware\hardOrs\Project Outputs for Ors\
+RelativeOutputPath5=V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\Project Outputs for OrsTypeC\
 OpenOutputs5=1
 AddToProject5=1
 TimestampFolder5=0

hardOrsTypeC/Project Outputs for OrsTypeC/Design Rule Check - OrsTypeC.drc

+Protel Design System Design Rule Check
+PCB File : V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\OrsTypeC.PcbDoc
+Date     : 04/05/2023
+Time     : 11:40:04
+
+Processing Rule : Clearance Constraint (Gap=0.35mm) (InNetClass('HighIsolation')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.21mm) (InPolygon),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.2mm) (InNamedPolygon('TOP-GND') OR InNamedPolygon('GND-BOTTOM_PWR1')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.12mm) (All),(IsVia)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.2mm) (InNamedPolygon('L4-+12V-2')OR  InNamedPolygon('L4-+12V')OR InNamedPolygon('BOTTOM+12V')OR InNamedPolygon('BOTTOM+12V-1')OR InNamedPolygon('L6_NoNet2') OR InNamedPolygon('L6_NoNet')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.5mm) (InNetClass('50OhmsL8tol4')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.5mm) (InNamedPolygon('L5_NoNet') OR InNamedPolygon('L6_NoNet') OR InNamedPolygon('L4_NoNet') OR InNamedPolygon('L7_NoNet')OR InNamedPolygon('L3_NoNet')),(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.1mm) (InNetClass('DiffPairNetClass')),(All)
+Rule Violations :0
+
+Processing Rule : Short-Circuit Constraint (Allowed=No) (All),(All)
+Rule Violations :0
+
+Processing Rule : Un-Routed Net Constraint ( (All) )
+Rule Violations :0
+
+Processing Rule : Power Plane Connect Rule(Direct Connect )(Expansion=0.508mm) (Conductor Width=0.254mm) (Air Gap=0.254mm) (Entries=4) (All)
+Rule Violations :0
+
+Processing Rule : Width Constraint (Min=0.1mm) (Max=10mm) (Preferred=0.254mm) (All)
+Rule Violations :0
+
+Processing Rule : Height Constraint (Min=0mm) (Max=25.4mm) (Prefered=12.7mm) (All)
+Rule Violations :0
+
+Processing Rule : Hole Size Constraint (Min=0.02mm) (Max=3.5mm) (All)
+Rule Violations :0
+
+Processing Rule : Hole To Hole Clearance (Gap=0.25mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Minimum Solder Mask Sliver (Gap=0.05mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Silk To Solder Mask (Clearance=0.2mm) (Disabled)(IsPad),(All)
+Rule Violations :0
+
+Processing Rule : Silk to Silk (Clearance=0.2mm) (Disabled)(All),(All)
+Rule Violations :0
+
+Processing Rule : Net Antennae (Tolerance=0mm) (Disabled)(All)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.6mm) (InNetClass('50OhmsL1toL2')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.1mm) (All),(All)
+Rule Violations :0
+
+Processing Rule : Matched Net Lengths(Tolerance=0.5mm) (InNetClass('POENetClass2'))
+Rule Violations :0
+
+Processing Rule : Matched Net Lengths(Tolerance=0.3mm) (InNetClass('POENetClass1'))
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.21mm) (InNetClass('50OhmsL8toL5')),(InPolygon)
+Rule Violations :0
+
+Processing Rule : Clearance Constraint (Gap=0.12mm) (InNetClass('DiffPairNetClass100Ohms_1_2')),(InPolygon)
+Rule Violations :0
+
+
+Violations Detected : 0
+Time Elapsed        : 00:02:18
\ No newline at end of file

hardOrsTypeC/Project Outputs for OrsTypeC/Gerber/Gerber Files.EXTREP

 ------------------------------------------------------------------------------------------
-Gerber File Extension Report For: Gerber Files.GBR   5/3/2023  5:23:37 PM
+Gerber File Extension Report For: Gerber Files.GBR   04/05/2023  11:59:09
 ------------------------------------------------------------------------------------------
 
 

hardOrsTypeC/Project Outputs for OrsTypeC/Gerber/Gerber Files.RUL

-DRC Rules Export File for PCB: Z:\ors-hardware\hardOrsTypeC\OrsTypeC.PcbDoc
+DRC Rules Export File for PCB: V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\OrsTypeC.PcbDoc
 RuleKind=Clearance|RuleName=HighIsolation|Scope=Board|Minimum=13.78
 RuleKind=Clearance|RuleName=PolyGon Clearance_ALL|Scope=Board|Minimum=8.27
 RuleKind=Clearance|RuleName=PolyGon Clearance_GND|Scope=Board|Minimum=7.87

hardOrsTypeC/Project Outputs for OrsTypeC/NC Drill/NC Drill Files.DRR

 ---------------------------------------------------------------------------
-NCDrill File Report For: OrsTypeC.PcbDoc   5/3/2023  5:23:47 PM
+NCDrill File Report For: OrsTypeC.PcbDoc   04/05/2023  11:59:23
 ---------------------------------------------------------------------------
 
 Layer Pair : TOP to BOTTOM
@@ -8,7 +8,7 @@ ASCII Non-Plated RoundHoles File : NC Drill Files-NonPlated.TXT
 
 Tool         Hole Size           Hole Type     Hole Count Plated       Tool Travel
 ---------------------------------------------------------------------------
-T1        0.2mm (7.874mil)         Round          2465             4593.09 mm (180.83 Inch)
+T1        0.2mm (7.874mil)         Round          2464             4600.70 mm (181.13 Inch)
 T2        0.25mm (9.842mil)        Round          1798             4540.06 mm (178.74 Inch)
 T3        0.3mm (11.811mil)        Round          224              929.30 mm (36.59 Inch)
 T4        0.5mm (19.685mil)        Round          34               313.99 mm (12.36 Inch)
@@ -16,6 +16,6 @@ T5        2.6mm (102.362mil)       Round          17               650.39 mm (25
 T6        3.25mm (127.953mil)      Round          4                35.10 mm (1.38 Inch)
 T7        1mm (39.37mil)           Round          8         NPTH   301.02 mm (11.85 Inch)
 ---------------------------------------------------------------------------
-Totals                                            4550             11362.96 mm (447.36 Inch)
+Totals                                            4549             11370.57 mm (447.66 Inch)
 
-Total Processing Time (hh:mm:ss) : 00:00:01
+Total Processing Time (hh:mm:ss) : 00:00:02

hardOrsTypeC/Project Outputs for OrsTypeC/NC Drill/NC Drill Files.LDP

-Layer Pairs Export File for PCB: Z:\ors-hardware\hardOrsTypeC\OrsTypeC.PcbDoc
+Layer Pairs Export File for PCB: V:\Work\Projets\RapidSpaceLocal\orsPanHardware\hardOrsTypeC\OrsTypeC.PcbDoc
 LayersSetName=Top_Bot_Plated_Thru_Holes|DrillFile=nc drill files-plated.txt|LayerPairs=gtl,gbl
 LayersSetName=Top_Bot_NonPlated_Thru_Holes|DrillFile=nc drill files-nonplated.txt|LayerPairs=gtl,gbl

hardOrsTypeC/Project Outputs for OrsTypeC/Pick Place/Pick Place for OrsTypeC(TDDB39).txt

@@ -516,7 +516,7 @@ C37xb      C0402              -83.9669mm     39.9892mm    -83.9669mm     39.9892
 C39xb      C0402              -84.6669mm     39.9892mm    -84.6669mm     39.9892mm    -84.6669mm     39.4892mm  T         90.00 CAP_SM100pF    
 C41xb      C0402-Phillips     -84.2743mm     41.7329mm    -84.2743mm     41.7329mm    -84.2743mm     42.2329mm  T        270.00 1uF            
 C42xb      C0402-Phillips     -80.8743mm     37.4329mm    -80.8743mm     37.4329mm    -80.8743mm     36.9329mm  T         90.00 1uF            
-C44xb      C0402              -86.8398mm      36.119mm    -86.8398mm      36.119mm    -86.8398mm      35.619mm  T         90.00 CAP_SM100pF    
+C44xb      C0402              -86.9373mm     36.2663mm    -86.9373mm     36.2663mm    -87.2909mm     35.9128mm  T         45.00 CAP_SM100pF    
 C45xb      C0402              -86.8169mm     42.8132mm    -86.8169mm     42.8132mm    -86.8169mm     42.3132mm  T         90.00 CAP_SM100pF    
 L5xb       NFM21PC            -82.1243mm     40.6329mm    -82.1243mm     40.6329mm    -83.1243mm     40.6329mm  T        360.00 EMIFIL_CAP     
 L6xb       L0603CS(1608)      -86.1243mm     40.8829mm    -86.1243mm     40.8829mm    -85.4743mm     40.8829mm  T        360.00 IND_SM-18nH 170m Ohms
@@ -781,7 +781,7 @@ CU8b       C0603              -109.596mm     24.6975mm    -109.596mm     24.6975
 CU6b       C0402              -95.5301mm     21.8028mm    -95.5301mm     21.8028mm    -95.5301mm     21.3028mm  B         90.00 CAP_SM100nF    
 CU5b       C0402              -94.4301mm     20.3028mm    -94.4301mm     20.3028mm    -94.9301mm     20.3028mm  B        360.00 CAP_SM100nF    
 CU4b       C0603              -94.1301mm     22.5028mm    -94.1301mm     22.5028mm    -94.1301mm     23.2528mm  B        270.00 CAP_SM4.7uF    
-CU2b       C0402              -90.3754mm     32.9635mm    -90.3754mm     32.9635mm    -89.9424mm     33.2135mm  T        210.00 CAP_SM100pF    
+CU2b       C0402              -90.1625mm     32.6855mm    -90.1625mm     32.6855mm    -89.8089mm     33.0391mm  T        225.00 CAP_SM100pF    
 CU1b       C0402              -105.321mm     21.9975mm    -105.321mm     21.9975mm    -105.321mm     22.4975mm  B        270.00 CAP_SM100pF    
 CA22       C0402              -73.6576mm       36.98mm    -73.6576mm       36.98mm    -74.0112mm     36.6265mm  B         45.00 CAP_SM100nF    
 CA28       C0402              -66.3273mm      37.143mm    -66.3273mm      37.143mm    -65.9737mm     36.7894mm  B        135.00 CAP_SM100nF    
@@ -790,7 +790,7 @@ CA22b2     C0402                -119.1mm        41.3mm      -119.1mm        41.3
 LC2xb2     NFM21PC              -117.8mm        43.2mm      -117.8mm        43.2mm      -118.8mm        43.2mm  B        360.00 EMIFIL_CAP     
 LC1x       NFM21PC            -73.3624mm     39.1392mm    -73.3624mm     39.1392mm    -72.6552mm     38.4321mm  B        135.00 EMIFIL_CAP     
 LC2x       NFM21PC            -68.5514mm     37.5378mm    -68.5514mm     37.5378mm    -69.2585mm     36.8306mm  B         45.00 EMIFIL_CAP     
-F3B38b     TAXXXX             -88.2926mm     34.2126mm    -88.7015mm     33.9126mm    -87.8836mm     34.0961mm  T        210.00 TA1968A        
+F3B38b     TAXXXX             -88.4158mm     34.5287mm     -88.787mm     34.1575mm    -88.0446mm     34.5464mm  T        225.00 TA1968A        
 F1B38      TAXXXX             -78.9273mm     73.3367mm    -79.0825mm     73.7554mm    -78.7375mm     73.4338mm  T        105.00 TA1968A        
 CU4        C0603              -36.9261mm      40.011mm    -36.9261mm      40.011mm    -37.4564mm     40.5413mm  B        315.00 CAP_SM4.7uF    
 CU5        C0402              -35.5826mm     38.2432mm    -35.5826mm     38.2432mm    -35.9361mm     37.8896mm  B         45.00 CAP_SM100nF    

hardOrsTypeC/Project Outputs for OrsTypeC/Pick Place/Pick Place for OrsTypeC(TDDB40).txt

@@ -516,7 +516,7 @@ C37xb      C0402              -83.9669mm     39.9892mm    -83.9669mm     39.9892
 C39xb      C0402              -84.6669mm     39.9892mm    -84.6669mm     39.9892mm    -84.6669mm     39.4892mm  T         90.00 CAP_SM100pF    
 C41xb      C0402-Phillips     -84.2743mm     41.7329mm    -84.2743mm     41.7329mm    -84.2743mm     42.2329mm  T        270.00 1uF            
 C42xb      C0402-Phillips     -80.8743mm     37.4329mm    -80.8743mm     37.4329mm    -80.8743mm     36.9329mm  T         90.00 1uF            
-C44xb      C0402              -86.8398mm      36.119mm    -86.8398mm      36.119mm    -86.8398mm      35.619mm  T         90.00 CAP_SM100pF    
+C44xb      C0402              -86.9373mm     36.2663mm    -86.9373mm     36.2663mm    -87.2909mm     35.9128mm  T         45.00 CAP_SM100pF    
 C45xb      C0402              -86.8169mm     42.8132mm    -86.8169mm     42.8132mm    -86.8169mm     42.3132mm  T         90.00 CAP_SM100pF    
 L5xb       NFM21PC            -82.1243mm     40.6329mm    -82.1243mm     40.6329mm    -83.1243mm     40.6329mm  T        360.00 EMIFIL_CAP     
 L6xb       L0603CS(1608)      -86.1243mm     40.8829mm    -86.1243mm     40.8829mm    -85.4743mm     40.8829mm  T        360.00 IND_SM-18nH 170m Ohms
@@ -781,7 +781,7 @@ CU8b       C0603              -109.596mm     24.6975mm    -109.596mm     24.6975
 CU6b       C0402              -95.5301mm     21.8028mm    -95.5301mm     21.8028mm    -95.5301mm     21.3028mm  B         90.00 CAP_SM100nF    
 CU5b       C0402              -94.4301mm     20.3028mm    -94.4301mm     20.3028mm    -94.9301mm     20.3028mm  B        360.00 CAP_SM100nF    
 CU4b       C0603              -94.1301mm     22.5028mm    -94.1301mm     22.5028mm    -94.1301mm     23.2528mm  B        270.00 CAP_SM4.7uF    
-CU2b       C0402              -90.3754mm     32.9635mm    -90.3754mm     32.9635mm    -89.9424mm     33.2135mm  T        210.00 CAP_SM100pF    
+CU2b       C0402              -90.1625mm     32.6855mm    -90.1625mm     32.6855mm    -89.8089mm     33.0391mm  T        225.00 CAP_SM100pF    
 CU1b       C0402              -105.321mm     21.9975mm    -105.321mm     21.9975mm    -105.321mm     22.4975mm  B        270.00 CAP_SM100pF    
 CA22       C0402              -73.6576mm       36.98mm    -73.6576mm       36.98mm    -74.0112mm     36.6265mm  B         45.00 CAP_SM100nF    
 CA28       C0402              -66.3273mm      37.143mm    -66.3273mm      37.143mm    -65.9737mm     36.7894mm  B        135.00 CAP_SM100nF    
@@ -790,7 +790,7 @@ CA22b2     C0402                -119.1mm        41.3mm      -119.1mm        41.3
 LC2xb2     NFM21PC              -117.8mm        43.2mm      -117.8mm        43.2mm      -118.8mm        43.2mm  B        360.00 EMIFIL_CAP     
 LC1x       NFM21PC            -73.3624mm     39.1392mm    -73.3624mm     39.1392mm    -72.6552mm     38.4321mm  B        135.00 EMIFIL_CAP     
 LC2x       NFM21PC            -68.5514mm     37.5378mm    -68.5514mm     37.5378mm    -69.2585mm     36.8306mm  B         45.00 EMIFIL_CAP     
-F3B38b     TAXXXX             -88.2926mm     34.2126mm    -88.7015mm     33.9126mm    -87.8836mm     34.0961mm  T        210.00 TA1968A        
+F3B38b     TAXXXX             -88.4158mm     34.5287mm     -88.787mm     34.1575mm    -88.0446mm     34.5464mm  T        225.00 TA1968A        
 F1B38      TAXXXX             -78.9273mm     73.3367mm    -79.0825mm     73.7554mm    -78.7375mm     73.4338mm  T        105.00 TA1968A        
 CU4        C0603              -36.9261mm      40.011mm    -36.9261mm      40.011mm    -37.4564mm     40.5413mm  B        315.00 CAP_SM4.7uF    
 CU5        C0402              -35.5826mm     38.2432mm    -35.5826mm     38.2432mm    -35.9361mm     37.8896mm  B         45.00 CAP_SM100nF    
@@ -814,8 +814,8 @@ LF1b2      L_TDK_0402        -101.7041mm     73.6657mm   -101.7041mm     73.6657
 LF1        L_TDK_0402          -79.321mm      74.742mm     -79.321mm      74.742mm    -79.0028mm     75.0602mm  T        225.00 IND_SM-        
 LF2b2      L_TDK_0402         -99.9527mm     71.5361mm    -99.9527mm     71.5361mm   -100.2708mm     71.2178mm  T         45.00 IND_SM-        
 LF2        L_TDK_0402         -77.6711mm      72.744mm    -77.6711mm      72.744mm     -77.353mm     73.0622mm  T        225.00 IND_SM-        
-LF3b       L_TDK_0402         -89.6211mm     33.9086mm    -89.6211mm     33.9086mm    -89.8461mm     34.2983mm  T        300.00 IND_SM-        
+LF3b       L_TDK_0402         -89.6476mm      33.845mm    -89.6476mm      33.845mm    -89.9658mm     34.1632mm  T        315.00 IND_SM-        
 LF3        L_TDK_0402         -41.7927mm     51.3214mm    -41.7927mm     51.3214mm    -42.2273mm     51.4379mm  T        345.00 IND_SM-        
-LF4b       L_TDK_0402         -87.6847mm     35.4085mm    -87.6847mm     35.4085mm    -87.9097mm     35.7983mm  T        300.00 IND_SM-        
+LF4b       L_TDK_0402         -87.4685mm      35.145mm    -87.4685mm      35.145mm    -87.1503mm     34.8268mm  T        135.00 IND_SM-        
 LF4        L_TDK_0402         -41.4898mm     53.7268mm    -41.4898mm     53.7268mm    -41.9245mm     53.8433mm  T        345.00 IND_SM-        
 

hardOrsTypeC/Project Outputs for OrsTypeC/Pick Place/Pick Place for OrsTypeC(TDDB41).txt

@@ -514,7 +514,7 @@ C37xb      C0402              -83.9669mm     39.9892mm    -83.9669mm     39.9892
 C39xb      C0402              -84.6669mm     39.9892mm    -84.6669mm     39.9892mm    -84.6669mm     39.4892mm  T         90.00 CAP_SM100pF    
 C41xb      C0402-Phillips     -84.2743mm     41.7329mm    -84.2743mm     41.7329mm    -84.2743mm     42.2329mm  T        270.00 1uF            
 C42xb      C0402-Phillips     -80.8743mm     37.4329mm    -80.8743mm     37.4329mm    -80.8743mm     36.9329mm  T         90.00 1uF            
-C44xb      C0402              -86.8398mm      36.119mm    -86.8398mm      36.119mm    -86.8398mm      35.619mm  T         90.00 CAP_SM100pF    
+C44xb      C0402              -86.9373mm     36.2663mm    -86.9373mm     36.2663mm    -87.2909mm     35.9128mm  T         45.00 CAP_SM100pF    
 C45xb      C0402              -86.8169mm     42.8132mm    -86.8169mm     42.8132mm    -86.8169mm     42.3132mm  T         90.00 CAP_SM100pF    
 L5xb       NFM21PC            -82.1243mm     40.6329mm    -82.1243mm     40.6329mm    -83.1243mm     40.6329mm  T        360.00 EMIFIL_CAP     
 L6xb       L0603CS(1608)      -86.1243mm     40.8829mm    -86.1243mm     40.8829mm    -85.4743mm     40.8829mm  T        360.00 IND_SM-18nH 170m Ohms
@@ -779,7 +779,7 @@ CU8b       C0603              -109.596mm     24.6975mm    -109.596mm     24.6975
 CU6b       C0402              -95.5301mm     21.8028mm    -95.5301mm     21.8028mm    -95.5301mm     21.3028mm  B         90.00 CAP_SM100nF    
 CU5b       C0402              -94.4301mm     20.3028mm    -94.4301mm     20.3028mm    -94.9301mm     20.3028mm  B        360.00 CAP_SM100nF    
 CU4b       C0603              -94.1301mm     22.5028mm    -94.1301mm     22.5028mm    -94.1301mm     23.2528mm  B        270.00 CAP_SM4.7uF    
-CU2b       C0402              -90.3754mm     32.9635mm    -90.3754mm     32.9635mm    -89.9424mm     33.2135mm  T        210.00 CAP_SM100pF    
+CU2b       C0402              -90.1625mm     32.6855mm    -90.1625mm     32.6855mm    -89.8089mm     33.0391mm  T        225.00 CAP_SM100pF    
 CU1b       C0402              -105.321mm     21.9975mm    -105.321mm     21.9975mm    -105.321mm     22.4975mm  B        270.00 CAP_SM100pF    
 CA22       C0402              -73.6576mm       36.98mm    -73.6576mm       36.98mm    -74.0112mm     36.6265mm  B         45.00 CAP_SM100nF    
 CA28       C0402              -66.3273mm      37.143mm    -66.3273mm      37.143mm    -65.9737mm     36.7894mm  B        135.00 CAP_SM100nF    
@@ -806,7 +806,7 @@ R140       R0402-Phillips        -60.7mm      137.95mm       -60.7mm      137.95
 Q3         SC70-3LD              -12.5mm        53.7mm       -12.5mm        53.7mm      -13.45mm       53.05mm  B        360.00 VDS= 20V ID= 100mA RDSON= 4 Ohm@VGS=4V
 R4         R0402                 -54.4mm       109.4mm       -54.4mm       109.4mm       -54.9mm       109.4mm  B        360.00 RES_SM-1k      
 R6         R0402                 -14.2mm        51.7mm       -14.2mm        51.7mm       -13.7mm        51.7mm  B        180.00 RES_SM-100k    
-F5B41b     TA2326C            -88.2846mm     34.2174mm    -88.3571mm     34.1131mm    -87.7033mm     34.1568mm  T         30.00 Filter Band 41 
+F5B41b     TA2326C            -88.4039mm     34.5426mm    -88.5063mm     34.4402mm    -87.8861mm     34.6517mm  T         45.00 Filter Band 41 
 F5B41      TA2326C            -41.0149mm     52.3937mm    -41.0434mm     52.3561mm     -40.612mm     52.8492mm  T         75.00 Filter Band 41 
 F7B41b2    TA2326C           -100.5938mm     72.7811mm   -100.6223mm     72.8188mm   -100.7493mm      72.176mm  T        285.00 Filter Band 41 
 F7B41      TA2326C            -78.9502mm     73.3303mm    -78.9787mm     73.3679mm    -79.1057mm     72.7252mm  T        285.00 Filter Band 41 
@@ -814,8 +814,8 @@ LF1b2      L_TDK_0402        -101.7041mm     73.6657mm   -101.7041mm     73.6657
 LF1        L_TDK_0402          -79.321mm      74.742mm     -79.321mm      74.742mm    -79.0028mm     75.0602mm  T        225.00 IND_SM-        
 LF2b2      L_TDK_0402         -99.9527mm     71.5361mm    -99.9527mm     71.5361mm   -100.2708mm     71.2178mm  T         45.00 IND_SM-        
 LF2        L_TDK_0402         -77.6711mm      72.744mm    -77.6711mm      72.744mm     -77.353mm     73.0622mm  T        225.00 IND_SM-        
-LF3b       L_TDK_0402         -89.6211mm     33.9086mm    -89.6211mm     33.9086mm    -89.8461mm     34.2983mm  T        300.00 IND_SM-        
+LF3b       L_TDK_0402         -89.6476mm      33.845mm    -89.6476mm      33.845mm    -89.9658mm     34.1632mm  T        315.00 IND_SM-        
 LF3        L_TDK_0402         -41.7927mm     51.3214mm    -41.7927mm     51.3214mm    -42.2273mm     51.4379mm  T        345.00 IND_SM-        
-LF4b       L_TDK_0402         -87.6847mm     35.4085mm    -87.6847mm     35.4085mm    -87.9097mm     35.7983mm  T        300.00 IND_SM-        
+LF4b       L_TDK_0402         -87.4685mm      35.145mm    -87.4685mm      35.145mm    -87.1503mm     34.8268mm  T        135.00 IND_SM-        
 LF4        L_TDK_0402         -41.4898mm     53.7268mm    -41.4898mm     53.7268mm    -41.9245mm     53.8433mm  T        345.00 IND_SM-        
 

hardOrsTypeC/Project Outputs for OrsTypeC/Status Report.Txt

+Output: NC Drill Files
+Type  : NC Drill
+From  : PCB Document [OrsTypeC.PcbDoc]
+   Generated File[NC Drill Files-Plated.TXT]
+   Generated File[NC Drill Files-NonPlated.TXT]
+   Generated File[NC Drill Files.LDP]
+   Generated File[NC Drill Files.DRR]
+
+
+Files Generated   : 4
+Documents Printed : 0
+
+Finished Output Generation At 11:59:25 On 04/05/2023