Merge tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "The code fixes in this round are all for the Texas Instruments OMAP
  platform, addressing several regressions related to the ti-sysc
  interconnect changes that was merged in linux-5.11 and one recently
  introduced RCU usage warning.

  Tero Kristo updates his maintainer file entries as he is changing to a
  new employer.

  The other changes are for devicetree files across eight different
  platforms:

  TI OMAP:
   - multiple gpio related one-line fixes

  Allwinner/sunxi:
   - ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
   - soc: sunxi: mbus: Remove DE2 display engine compatibles

  NXP lpc32xx:
   - ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL

  STMicroelectronics stm32
   - multiple minor fixes for DHCOM/DHCOR boards

  NXP Layerscape:
   - Fix DCFG address range on LS1046A SoC

  Amlogic meson:
   - fix reboot issue on odroid C4
   - revert an ethernet change that caused a regression
   - meson-g12: Set FL-adj property value

  Rockchip:
   - multiple minor fixes on 64-bit rockchip machines

  Qualcomm:
   - Regression fixes for Lenovo Yoga touchpad and for interconnect
     configuration
   - Boot fixes for 'LPASS' clock configuration on two machines"

* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  arm64: dts: ls1046a: fix dcfg address range
  soc: sunxi: mbus: Remove DE2 display engine compatibles
  arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
  Revert "arm64: dts: amlogic: add missing ethernet reset ID"
  arm64: dts: rockchip: Disable display for NanoPi R2S
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
  arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
  ...

MAINTAINERS

@@ -2616,8 +2616,8 @@ S:	Maintained
 F:	drivers/power/reset/keystone-reset.c
 
 ARM/TEXAS INSTRUMENTS K3 ARCHITECTURE
-M:	Tero Kristo <t-kristo@ti.com>
 M:	Nishanth Menon <nm@ti.com>
+M:	Tero Kristo <kristo@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -6474,9 +6474,9 @@ S:	Maintained
 F:	drivers/edac/skx_*.[ch]
 
 EDAC-TI
-M:	Tero Kristo <t-kristo@ti.com>
+M:	Tero Kristo <kristo@kernel.org>
 L:	linux-edac@vger.kernel.org
-S:	Maintained
+S:	Odd Fixes
 F:	drivers/edac/ti_edac.c
 
 EDIROL UA-101/UA-1000 DRIVER
@@ -17572,7 +17572,7 @@ F:	include/linux/dma/k3-psil.h
 
 TEXAS INSTRUMENTS' SYSTEM CONTROL INTERFACE (TISCI) PROTOCOL DRIVER
 M:	Nishanth Menon <nm@ti.com>
-M:	Tero Kristo <t-kristo@ti.com>
+M:	Tero Kristo <kristo@kernel.org>
 M:	Santosh Shilimkar <ssantosh@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org
 S:	Maintained
@@ -17716,9 +17716,9 @@ S:	Maintained
 F:	drivers/clk/clk-cdce706.c
 
 TI CLOCK DRIVER
-M:	Tero Kristo <t-kristo@ti.com>
+M:	Tero Kristo <kristo@kernel.org>
 L:	linux-omap@vger.kernel.org
-S:	Maintained
+S:	Odd Fixes
 F:	drivers/clk/ti/
 F:	include/linux/clk/ti.h
 

arch/arm/boot/dts/lpc32xx.dtsi

@@ -326,9 +326,6 @@ clk: clock-controller@0 {
 
 					clocks = <&xtal_32k>, <&xtal>;
 					clock-names = "xtal_32k", "xtal";
-
-					assigned-clocks = <&clk LPC32XX_CLK_HCLK_PLL>;
-					assigned-clock-rates = <208000000>;
 				};
 			};
 

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -114,7 +114,7 @@ spi_lcd: spi_lcd {
 		gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>;
 		gpio-miso = <&gpio1 18 GPIO_ACTIVE_HIGH>;
 		gpio-mosi = <&gpio1 20 GPIO_ACTIVE_HIGH>;
-		cs-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
 		/* lcd panel */
@@ -124,7 +124,6 @@ lcd: td028ttec1@0 {
 			spi-max-frequency = <100000>;
 			spi-cpol;
 			spi-cpha;
-			spi-cs-high;
 
 			backlight= <&backlight>;
 			label = "lcd";

arch/arm/boot/dts/omap4-droid4-xt894.dts

@@ -16,8 +16,13 @@ volume_down {
 			debounce-interval = <10>;
 		};
 
+		/*
+		 * We use pad 0x4a100116 abe_dmic_din3.gpio_122 as the irq instead
+		 * of the gpio interrupt to avoid lost events in deeper idle states.
+		*/
 		slider {
 			label = "Keypad Slide";
+			interrupts-extended = <&omap4_pmx_core 0xd6>;
 			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
 			linux,input-type = <EV_SW>;
 			linux,code = <SW_KEYPAD_SLIDE>;

arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi

@@ -33,9 +33,9 @@ &gpiob {
 	 * during TX anyway and that it only controls drive enable DE
 	 * line. Hence, the RX is always enabled here.
 	 */
-	rs485-rx-en {
+	rs485-rx-en-hog {
 		gpio-hog;
-		gpios = <8 GPIO_ACTIVE_HIGH>;
+		gpios = <8 0>;
 		output-low;
 		line-name = "rs485-rx-en";
 	};
@@ -61,9 +61,9 @@ &gpioi {
 	 * order to reset the Hub when USB bus is powered down, but
 	 * so far there is no such functionality.
 	 */
-	usb-hub {
+	usb-hub-hog {
 		gpio-hog;
-		gpios = <2 GPIO_ACTIVE_HIGH>;
+		gpios = <2 0>;
 		output-high;
 		line-name = "usb-hub-reset";
 	};
@@ -87,6 +87,12 @@ eeprom@50 {
 	};
 };
 
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
 &i2c5 {	/* TP7/TP8 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c5_pins_a>;
@@ -104,7 +110,7 @@ &sdmmc3 {
 	 * are used for on-board microSD slot instead.
 	 */
 	/delete-property/broken-cd;
-	cd-gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
 	disable-wp;
 };
 

arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi

@@ -43,9 +43,9 @@ &gpioa {
 	 * in order to turn on port power when USB bus is powered up, but so
 	 * far there is no such functionality.
 	 */
-	usb-port-power {
+	usb-port-power-hog {
 		gpio-hog;
-		gpios = <13 GPIO_ACTIVE_LOW>;
+		gpios = <13 0>;
 		output-low;
 		line-name = "usb-port-power";
 	};

arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi

@@ -390,7 +390,8 @@ &sdmmc1 {
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
-	broken-cd;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
 	st,use-ckin;

arch/arm/boot/dts/sun7i-a20-bananapro.dts

@@ -110,7 +110,7 @@ &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&reg_gmac_3v3>;
 	status = "okay";
 };

arch/arm/mach-omap1/board-osk.c

@@ -203,6 +203,8 @@ static int osk_tps_setup(struct i2c_client *client, void *context)
 	 */
 	gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
 	gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
+	/* Free the GPIO again as the driver will request it */
+	gpio_free(OSK_TPS_GPIO_USB_PWR_EN);
 
 	/* Set GPIO 2 high so LED D3 is off by default */
 	tps65010_set_gpio_out_value(GPIO2, HIGH);

arch/arm/mach-omap2/Kconfig

@@ -17,11 +17,10 @@ config ARCH_OMAP3
 	bool "TI OMAP3"
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 	select OMAP_HWMOD
 	select OMAP_INTERCONNECT
-	select PM_OPP if PM
-	select PM if CPU_IDLE
+	select PM_OPP
 	select SOC_HAS_OMAP2_SDRC
 	select ARM_ERRATA_430973
 
@@ -30,7 +29,7 @@ config ARCH_OMAP4
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
 	select ARCH_NEEDS_CPU_IDLE_COUPLED if SMP
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 	select ARM_ERRATA_720789
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
@@ -40,7 +39,7 @@ config ARCH_OMAP4
 	select OMAP_INTERCONNECT_BARRIER
 	select PL310_ERRATA_588369 if CACHE_L2X0
 	select PL310_ERRATA_727915 if CACHE_L2X0
-	select PM_OPP if PM
+	select PM_OPP
 	select PM if CPU_IDLE
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_775420
@@ -50,7 +49,7 @@ config SOC_OMAP5
 	bool "TI OMAP5"
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_ARCH_TIMER
@@ -58,14 +57,14 @@ config SOC_OMAP5
 	select OMAP_HWMOD
 	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
-	select PM_OPP if PM
+	select PM_OPP
 	select ZONE_DMA if ARM_LPAE
 
 config SOC_AM33XX
 	bool "TI AM33XX"
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 
 config SOC_AM43XX
 	bool "TI AM43x"
@@ -79,13 +78,13 @@ config SOC_AM43XX
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_775420
 	select OMAP_INTERCONNECT
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 
 config SOC_DRA7XX
 	bool "TI DRA7XX"
 	depends on ARCH_MULTI_V7
 	select ARCH_OMAP2PLUS
-	select ARM_CPU_SUSPEND if PM
+	select ARM_CPU_SUSPEND
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_ARCH_TIMER
@@ -94,7 +93,7 @@ config SOC_DRA7XX
 	select OMAP_HWMOD
 	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
-	select PM_OPP if PM
+	select PM_OPP
 	select ZONE_DMA if ARM_LPAE
 	select PINCTRL_TI_IODELAY if OF && PINCTRL
 
@@ -112,9 +111,11 @@ config ARCH_OMAP2PLUS
 	select OMAP_DM_TIMER
 	select OMAP_GPMC
 	select PINCTRL
-	select PM_GENERIC_DOMAINS if PM
-	select PM_GENERIC_DOMAINS_OF if PM
+	select PM
+	select PM_GENERIC_DOMAINS
+	select PM_GENERIC_DOMAINS_OF
 	select RESET_CONTROLLER
+	select SIMPLE_PM_BUS
 	select SOC_BUS
 	select TI_SYSC
 	select OMAP_IRQCHIP
@@ -140,7 +141,6 @@ config ARCH_OMAP2PLUS_TYPICAL
 	select I2C_OMAP
 	select MENELAUS if ARCH_OMAP2
 	select NEON if CPU_V7
-	select PM
 	select REGULATOR
 	select REGULATOR_FIXED_VOLTAGE
 	select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4

arch/arm/mach-omap2/cpuidle44xx.c

@@ -151,10 +151,10 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 				 (cx->mpu_logic_state == PWRDM_POWER_OFF);
 
 	/* Enter broadcast mode for periodic timers */
-	tick_broadcast_enable();
+	RCU_NONIDLE(tick_broadcast_enable());
 
 	/* Enter broadcast mode for one-shot timers */
-	tick_broadcast_enter();
+	RCU_NONIDLE(tick_broadcast_enter());
 
 	/*
 	 * Call idle CPU PM enter notifier chain so that
@@ -166,7 +166,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 
 	if (dev->cpu == 0) {
 		pwrdm_set_logic_retst(mpu_pd, cx->mpu_logic_state);
-		omap_set_pwrdm_state(mpu_pd, cx->mpu_state);
+		RCU_NONIDLE(omap_set_pwrdm_state(mpu_pd, cx->mpu_state));
 
 		/*
 		 * Call idle CPU cluster PM enter notifier chain
@@ -178,7 +178,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 				index = 0;
 				cx = state_ptr + index;
 				pwrdm_set_logic_retst(mpu_pd, cx->mpu_logic_state);
-				omap_set_pwrdm_state(mpu_pd, cx->mpu_state);
+				RCU_NONIDLE(omap_set_pwrdm_state(mpu_pd, cx->mpu_state));
 				mpuss_can_lose_context = 0;
 			}
 		}
@@ -194,9 +194,9 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 		    mpuss_can_lose_context)
 			gic_dist_disable();
 
-		clkdm_deny_idle(cpu_clkdm[1]);
-		omap_set_pwrdm_state(cpu_pd[1], PWRDM_POWER_ON);
-		clkdm_allow_idle(cpu_clkdm[1]);
+		RCU_NONIDLE(clkdm_deny_idle(cpu_clkdm[1]));
+		RCU_NONIDLE(omap_set_pwrdm_state(cpu_pd[1], PWRDM_POWER_ON));
+		RCU_NONIDLE(clkdm_allow_idle(cpu_clkdm[1]));
 
 		if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) &&
 		    mpuss_can_lose_context) {
@@ -222,7 +222,7 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 	cpu_pm_exit();
 
 cpu_pm_out:
-	tick_broadcast_exit();
+	RCU_NONIDLE(tick_broadcast_exit());
 
 fail:
 	cpuidle_coupled_parallel_barrier(dev, &abort_barrier);

arch/arm/mach-omap2/pdata-quirks.c

@@ -522,6 +522,7 @@ static struct of_dev_auxdata omap_auxdata_lookup[] = {
 		       &dra7_ipu1_dsp_iommu_pdata),
 #endif
 	/* Common auxdata */
+	OF_DEV_AUXDATA("simple-pm-bus", 0, NULL, omap_auxdata_lookup),
 	OF_DEV_AUXDATA("ti,sysc", 0, NULL, &ti_sysc_pdata),
 	OF_DEV_AUXDATA("pinctrl-single", 0, NULL, &pcs_pdata),
 	OF_DEV_AUXDATA("ti,omap-prm-inst", 0, NULL, &ti_prm_pdata),

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -280,8 +280,6 @@ ethmac: ethernet@ff3f0000 {
 				      "timing-adjustment";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
-			resets = <&reset RESET_ETHERNET>;
-			reset-names = "stmmaceth";
 			power-domains = <&pwrc PWRC_AXG_ETHERNET_MEM_ID>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi

@@ -224,8 +224,6 @@ ethmac: ethernet@ff3f0000 {
 				      "timing-adjustment";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
-			resets = <&reset RESET_ETHERNET>;
-			reset-names = "stmmaceth";
 			status = "disabled";
 
 			mdio0: mdio {
@@ -2390,7 +2388,7 @@ dwc3: usb@ff500000 {
 				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 				dr_mode = "host";
 				snps,dis_u2_susphy_quirk;
-				snps,quirk-frame-length-adjustment;
+				snps,quirk-frame-length-adjustment = <0x20>;
 				snps,parkmode-disable-ss-quirk;
 			};
 		};

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -13,7 +13,6 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/meson-gxbb-power.h>
-#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -576,8 +575,6 @@ ethmac: ethernet@c9410000 {
 			interrupt-names = "macirq";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
-			resets = <&reset RESET_ETHERNET>;
-			reset-names = "stmmaceth";
 			power-domains = <&pwrc PWRC_GXBB_ETHERNET_MEM_ID>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts

@@ -52,7 +52,7 @@ tflash_vdd: regulator-tflash_vdd {
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
-		gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 	};

arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi

@@ -385,7 +385,7 @@ bportals: bman-portals@508000000 {
 
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1046a-dcfg", "syscon";
-			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			reg = <0x0 0x1ee0000 0x0 0x1000>;
 			big-endian;
 		};
 

arch/arm64/boot/dts/qcom/sdm845-db845c.dts

@@ -415,7 +415,9 @@ &dsi0_phy {
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
-			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
 };
 
 &gpu {

arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts

@@ -302,7 +302,9 @@ &dsi0_phy {
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
-			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
 };
 
 &gpu {
@@ -320,6 +322,8 @@ &i2c1 {
 &i2c3 {
 	status = "okay";
 	clock-frequency = <400000>;
+	/* Overwrite pinctrl-0 from sdm845.dtsi */
+	pinctrl-0 = <&qup_i2c3_default &i2c3_hid_active>;
 
 	tsel: hid@15 {
 		compatible = "hid-over-i2c";
@@ -327,9 +331,6 @@ tsel: hid@15 {
 		hid-descr-addr = <0x1>;
 
 		interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c3_hid_active>;
 	};
 
 	tsc2: hid@2c {
@@ -338,11 +339,6 @@ tsc2: hid@2c {
 		hid-descr-addr = <0x20>;
 
 		interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c3_hid_active>;
-
-		status = "disabled";
 	};
 };
 

arch/arm64/boot/dts/rockchip/px30.dtsi

@@ -1097,7 +1097,7 @@ vopl_out_lvds: endpoint@1 {
 	vopl_mmu: iommu@ff470f00 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff470f00 0x0 0x100>;
-		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "vopl_mmu";
 		clocks = <&cru ACLK_VOPL>, <&cru HCLK_VOPL>;
 		clock-names = "aclk", "iface";

arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts

@@ -114,6 +114,10 @@ &cpu3 {
 	cpu-supply = <&vdd_arm>;
 };
 
+&display_subsystem {
+	status = "disabled";
+};
+
 &gmac2io {
 	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
 	assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;

arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts

@@ -790,7 +790,6 @@ &pcie_phy {
 &pcie0 {
 	bus-scan-delay-ms = <1000>;
 	ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
-	max-link-speed = <2>;
 	num-lanes = <4>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie_clkreqn_cpm>;

arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -234,6 +234,7 @@ pcie0: pcie@f8000000 {
 		reg = <0x0 0xf8000000 0x0 0x2000000>,
 		      <0x0 0xfd000000 0x0 0x1000000>;
 		reg-names = "axi-base", "apb-base";
+		device_type = "pci";
 		#address-cells = <3>;
 		#size-cells = <2>;
 		#interrupt-cells = <1>;
@@ -252,7 +253,6 @@ pcie0: pcie@f8000000 {
 				<0 0 0 2 &pcie0_intc 1>,
 				<0 0 0 3 &pcie0_intc 2>,
 				<0 0 0 4 &pcie0_intc 3>;
-		linux,pci-domain = <0>;
 		max-link-speed = <1>;
 		msi-map = <0x0 &its 0x0 0x1000>;
 		phys = <&pcie_phy 0>, <&pcie_phy 1>,
@@ -1278,7 +1278,6 @@ vdec: video-codec@ff660000 {
 		compatible = "rockchip,rk3399-vdec";
 		reg = <0x0 0xff660000 0x0 0x400>;
 		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "vdpu";
 		clocks = <&cru ACLK_VDU>, <&cru HCLK_VDU>,
 			 <&cru SCLK_VDU_CA>, <&cru SCLK_VDU_CORE>;
 		clock-names = "axi", "ahb", "cabac", "core";

arch/arm64/configs/defconfig

@@ -1076,7 +1076,7 @@ CONFIG_INTERCONNECT=y
 CONFIG_INTERCONNECT_QCOM=y
 CONFIG_INTERCONNECT_QCOM_MSM8916=m
 CONFIG_INTERCONNECT_QCOM_OSM_L3=m
-CONFIG_INTERCONNECT_QCOM_SDM845=m
+CONFIG_INTERCONNECT_QCOM_SDM845=y
 CONFIG_INTERCONNECT_QCOM_SM8150=m
 CONFIG_INTERCONNECT_QCOM_SM8250=m
 CONFIG_EXT2_FS=y

drivers/bus/simple-pm-bus.c

@@ -16,6 +16,7 @@
 
 static int simple_pm_bus_probe(struct platform_device *pdev)
 {
+	const struct of_dev_auxdata *lookup = dev_get_platdata(&pdev->dev);
 	struct device_node *np = pdev->dev.of_node;
 
 	dev_dbg(&pdev->dev, "%s\n", __func__);
@@ -23,7 +24,7 @@ static int simple_pm_bus_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 
 	if (np)
-		of_platform_populate(np, NULL, NULL, &pdev->dev);
+		of_platform_populate(np, NULL, lookup, &pdev->dev);
 
 	return 0;
 }

drivers/soc/sunxi/sunxi_mbus.c

@@ -23,12 +23,7 @@ static const char * const sunxi_mbus_devices[] = {
 	"allwinner,sun7i-a20-display-engine",
 	"allwinner,sun8i-a23-display-engine",
 	"allwinner,sun8i-a33-display-engine",
-	"allwinner,sun8i-a83t-display-engine",
-	"allwinner,sun8i-h3-display-engine",
-	"allwinner,sun8i-r40-display-engine",
-	"allwinner,sun8i-v3s-display-engine",
 	"allwinner,sun9i-a80-display-engine",
-	"allwinner,sun50i-a64-display-engine",
 
 	/*
 	 * And now we have the regular devices connected to the MBUS

drivers/soc/ti/omap_prm.c

@@ -860,6 +860,7 @@ static int omap_prm_reset_init(struct platform_device *pdev,
 	const struct omap_rst_map *map;
 	struct ti_prm_platform_data *pdata = dev_get_platdata(&pdev->dev);
 	char buf[32];
+	u32 v;
 
 	/*
 	 * Check if we have controllable resets. If either rstctrl is non-zero
@@ -907,6 +908,16 @@ static int omap_prm_reset_init(struct platform_device *pdev,
 		map++;
 	}
 
+	/* Quirk handling to assert rst_map_012 bits on reset and avoid errors */
+	if (prm->data->rstmap == rst_map_012) {
+		v = readl_relaxed(reset->prm->base + reset->prm->data->rstctrl);
+		if ((v & reset->mask) != reset->mask) {
+			dev_dbg(&pdev->dev, "Asserting all resets: %08x\n", v);
+			writel_relaxed(reset->mask, reset->prm->base +
+				       reset->prm->data->rstctrl);
+		}
+	}
+
 	return devm_reset_controller_register(&pdev->dev, &reset->rcdev);
 }