Merge tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu into next/dt

Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:

The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.

Besides them there are 2 other patches:
 - One adding the crypto support for Armada 37xx SoCs
 - An other adding Ethernet aliases on A7K/A8K base boards

* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: add Ethernet aliases
  arm64: dts: marvell: replace cpm by cp0, cps by cp1
  arm64: dts: marvell: de-duplicate CP110 description
  arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
  arm64: dts: marvell: use mvebu-icu.h where possible
  arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
  arm64: dts: marvell: fix typos in comment describing the NAND controller
  arm64: dts: marvell: use lower case for unit address and reg property
  arm64: dts: marvell: fix watchdog unit address in Armada AP806
  arm64: dts: marvell: armada-37xx: add a crypto node
  ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
  ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7

arch/arm/boot/dts/kirkwood-openblocks_a7.dts

@@ -53,7 +53,8 @@ s24c02: s24c02@50 {
 		};
 
 		pinctrl: pin-controller@10000 {
-			pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header>;
+			pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header
+				     &pmx_gpio_header_gpo>;
 			pinctrl-names = "default";
 
 			pmx_uart0: pmx-uart0 {
@@ -85,11 +86,16 @@ pmx_dip_switches: pmx-dip-switches {
 			 * ground.
 			 */
 			pmx_gpio_header: pmx-gpio-header {
-				marvell,pins = "mpp17", "mpp7", "mpp29", "mpp28",
+				marvell,pins = "mpp17", "mpp29", "mpp28",
 					       "mpp35", "mpp34", "mpp40";
 				marvell,function = "gpio";
 			};
 
+			pmx_gpio_header_gpo: pxm-gpio-header-gpo {
+				marvell,pins = "mpp7";
+				marvell,function = "gpo";
+			};
+
 			pmx_gpio_init: pmx-init {
 				marvell,pins = "mpp38";
 				marvell,function = "gpio";

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -316,6 +316,20 @@ xor11 {
 				};
 			};
 
+			crypto: crypto@90000 {
+				compatible = "inside-secure,safexcel-eip97";
+				reg = <0x90000 0x20000>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "mem", "ring0", "ring1",
+						  "ring2", "ring3", "eip";
+				clocks = <&nb_periph_clk 15>;
+			};
+
 			sdhci1: sdhci@d0000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";

arch/arm64/boot/dts/marvell/armada-7040-db.dts

@@ -61,7 +61,13 @@ memory@0 {
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+	};
+
+	cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
@@ -70,7 +76,7 @@ cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
 		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+	cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3h1-vbus";
 		regulator-min-microvolt = <5000000>;
@@ -79,14 +85,14 @@ cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
 		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_usb3_0_phy: cpm-usb3-0-phy {
+	cp0_usb3_0_phy: cp0-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_0_vbus>;
+		vcc-supply = <&cp0_reg_usb3_0_vbus>;
 	};
 
-	cpm_usb3_1_phy: cpm-usb3-1-phy {
+	cp0_usb3_1_phy: cp0-usb3-1-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_1_vbus>;
+		vcc-supply = <&cp0_reg_usb3_1_vbus>;
 	};
 };
 
@@ -129,11 +135,11 @@ &uart0 {
 };
 
 
-&cpm_pcie2 {
+&cp0_pcie2 {
 	status = "okay";
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 
@@ -156,7 +162,7 @@ expander0: pca9555@21 {
 	};
 };
 
-&cpm_nand {
+&cp0_nand {
 	/*
 	 * SPI on CPM and NAND have common pins on this board. We can
 	 * use only one at a time. To enable the NAND (whihch will
@@ -186,7 +192,7 @@ partition@1000000 {
 };
 
 
-&cpm_spi1 {
+&cp0_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
@@ -214,17 +220,17 @@ partition@400000 {
 	};
 };
 
-&cpm_sata0 {
+&cp0_sata0 {
 	status = "okay";
 };
 
-&cpm_usb3_0 {
-	usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+	usb-phy = <&cp0_usb3_0_phy>;
 	status = "okay";
 };
 
-&cpm_usb3_1 {
-	usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+	usb-phy = <&cp0_usb3_1_phy>;
 	status = "okay";
 };
 
@@ -235,14 +241,14 @@ &ap_sdhci0 {
 	non-removable;
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	status = "okay";
 	bus-width = <4>;
 	no-1-8-v;
 	cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>;
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -253,28 +259,28 @@ phy1: ethernet-phy@1 {
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy2 0>;
+	phys = <&cp0_comphy2 0>;
 };
 
-&cpm_eth1 {
+&cp0_eth1 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "sgmii";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy0 1>;
+	phys = <&cp0_comphy0 1>;
 };
 
-&cpm_eth2 {
+&cp0_eth2 {
 	status = "okay";
 	phy = <&phy1>;
 	phy-mode = "rgmii-id";

arch/arm64/boot/dts/marvell/armada-70x0.dtsi

@@ -44,25 +44,46 @@
  * Device Tree file for the Armada 70x0 SoC
  */
 
-#include "armada-cp110-master.dtsi"
-
 / {
 	aliases {
-		gpio1 = &cpm_gpio1;
-		gpio2 = &cpm_gpio2;
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
 	};
 };
 
-&cpm_gpio1 {
+/*
+ * Instantiate the CP110
+ */
+#define CP110_NAME		cp0
+#define CP110_BASE		f2000000
+#define CP110_PCIE_IO_BASE	0xf9000000
+#define CP110_PCIE_MEM_BASE	0xf6000000
+#define CP110_PCIE0_BASE	f2600000
+#define CP110_PCIE1_BASE	f2620000
+#define CP110_PCIE2_BASE	f2640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
+&cp0_gpio1 {
 	status = "okay";
 };
 
-&cpm_gpio2 {
+&cp0_gpio2 {
 	status = "okay";
 };
 
-&cpm_syscon0 {
-	cpm_pinctrl: pinctrl {
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
 		compatible = "marvell,armada-7k-pinctrl";
 
 		nand_pins: nand-pins {

arch/arm64/boot/dts/marvell/armada-8020.dtsi

@@ -60,6 +60,6 @@ / {
  * oscillator so this one is let enabled.
  */
 
-&cpm_rtc {
+&cp0_rtc {
 	status = "disabled";
 };

arch/arm64/boot/dts/marvell/armada-8040-db.dts

@@ -61,46 +61,53 @@ memory@0 {
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
-	cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth2;
+		ethernet2 = &cp1_eth0;
+		ethernet3 = &cp1_eth1;
+	};
+
+	cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cpm-usb3h0-vbus";
+		regulator-name = "cp0-usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
+	cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cpm-usb3h1-vbus";
+		regulator-name = "cp0-usb3h1-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
 	};
 
-	cpm_usb3_0_phy: cpm-usb3-0-phy {
+	cp0_usb3_0_phy: cp0-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_0_vbus>;
+		vcc-supply = <&cp0_reg_usb3_0_vbus>;
 	};
 
-	cpm_usb3_1_phy: cpm-usb3-1-phy {
+	cp0_usb3_1_phy: cp0-usb3-1-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cpm_reg_usb3_1_vbus>;
+		vcc-supply = <&cp0_reg_usb3_1_vbus>;
 	};
 
-	cps_reg_usb3_0_vbus: cps-usb3-0-vbus {
+	cp1_reg_usb3_0_vbus: cp1-usb3-0-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "cps-usb3h0-vbus";
+		regulator-name = "cp1-usb3h0-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&expander1 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	cps_usb3_0_phy: cps-usb3-0-phy {
+	cp1_usb3_0_phy: cp1-usb3-0-phy {
 		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cps_reg_usb3_0_vbus>;
+		vcc-supply = <&cp1_reg_usb3_0_vbus>;
 	};
 };
 
@@ -144,16 +151,16 @@ &uart0 {
 };
 
 /* CON6 on CP0 expansion */
-&cpm_pcie0 {
+&cp0_pcie0 {
 	status = "okay";
 };
 
 /* CON5 on CP0 expansion */
-&cpm_pcie2 {
+&cp0_pcie2 {
 	status = "okay";
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 
@@ -178,23 +185,23 @@ expander1: pca9555@25 {
 };
 
 /* CON4 on CP0 expansion */
-&cpm_sata0 {
+&cp0_sata0 {
 	status = "okay";
 };
 
 /* CON9 on CP0 expansion */
-&cpm_usb3_0 {
-	usb-phy = <&cpm_usb3_0_phy>;
+&cp0_usb3_0 {
+	usb-phy = <&cp0_usb3_0_phy>;
 	status = "okay";
 };
 
 /* CON10 on CP0 expansion */
-&cpm_usb3_1 {
-	usb-phy = <&cpm_usb3_1_phy>;
+&cp0_usb3_1 {
+	usb-phy = <&cp0_usb3_1_phy>;
 	status = "okay";
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
@@ -202,42 +209,42 @@ phy1: ethernet-phy@1 {
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	phy-mode = "10gbase-kr";
 };
 
-&cpm_eth2 {
+&cp0_eth2 {
 	status = "okay";
 	phy = <&phy1>;
 	phy-mode = "rgmii-id";
 };
 
 /* CON6 on CP1 expansion */
-&cps_pcie0 {
+&cp1_pcie0 {
 	status = "okay";
 };
 
 /* CON7 on CP1 expansion */
-&cps_pcie1 {
+&cp1_pcie1 {
 	status = "okay";
 };
 
 /* CON5 on CP1 expansion */
-&cps_pcie2 {
+&cp1_pcie2 {
 	status = "okay";
 };
 
-&cps_i2c0 {
+&cp1_i2c0 {
 	status = "okay";
 	clock-frequency = <100000>;
 };
 
-&cps_spi1 {
+&cp1_spi1 {
 	status = "okay";
 
 	spi-flash@0 {
@@ -272,14 +279,14 @@ partition@f00000 {
  * Proper NAND usage will require DPR-76 to be in position 1-2, which disables
  * MDIO signal of CP1.
  */
-&cps_nand {
+&cp1_nand {
 	num-cs = <1>;
 	pinctrl-0 = <&nand_pins>, <&nand_rb>;
 	pinctrl-names = "default";
 	nand-ecc-strength = <4>;
 	nand-ecc-step-size = <512>;
 	marvell,nand-enable-arbiter;
-	marvell,system-controller = <&cps_syscon0>;
+	marvell,system-controller = <&cp1_syscon0>;
 	nand-on-flash-bbt;
 
 	partition@0 {
@@ -297,22 +304,22 @@ partition@1000000 {
 };
 
 /* CON4 on CP1 expansion */
-&cps_sata0 {
+&cp1_sata0 {
 	status = "okay";
 };
 
 /* CON9 on CP1 expansion */
-&cps_usb3_0 {
-	usb-phy = <&cps_usb3_0_phy>;
+&cp1_usb3_0 {
+	usb-phy = <&cp1_usb3_0_phy>;
 	status = "okay";
 };
 
 /* CON10 on CP1 expansion */
-&cps_usb3_1 {
+&cp1_usb3_1 {
 	status = "okay";
 };
 
-&cps_mdio {
+&cp1_mdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -320,16 +327,16 @@ phy0: ethernet-phy@0 {
 	};
 };
 
-&cps_ethernet {
+&cp1_ethernet {
 	status = "okay";
 };
 
-&cps_eth0 {
+&cp1_eth0 {
 	status = "okay";
 	phy-mode = "10gbase-kr";
 };
 
-&cps_eth1 {
+&cp1_eth1 {
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";
@@ -341,7 +348,7 @@ &ap_sdhci0 {
 	non-removable;
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	status = "okay";
 	bus-width = <8>;
 	non-removable;

arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts

@@ -62,6 +62,12 @@ memory@0 {
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
 
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp1_eth0;
+		ethernet2 = &cp1_eth1;
+	};
+
 	/* Regulator labels correspond with schematics */
 	v_3_3: regulator-3-3v {
 		compatible = "regulator-fixed";
@@ -84,9 +90,9 @@ v_vddo_h: regulator-1-8v {
 	v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio = <&cpm_gpio2 15 GPIO_ACTIVE_HIGH>;
+		gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cpm_xhci_vbus_pins>;
+		pinctrl-0 = <&cp0_xhci_vbus_pins>;
 		regulator-name = "v_5v0_usb3_hst_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -120,17 +126,17 @@ &ap_sdhci0 {
 	vqmmc-supply = <&v_vddo_h>;
 };
 
-&cpm_i2c0 {
+&cp0_i2c0 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_i2c0_pins>;
+	pinctrl-0 = <&cp0_i2c0_pins>;
 	status = "okay";
 };
 
-&cpm_i2c1 {
+&cp0_i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_i2c1_pins>;
+	pinctrl-0 = <&cp0_i2c1_pins>;
 	status = "okay";
 
 	i2c-switch@70 {
@@ -157,9 +163,9 @@ sfp_1g_i2c: i2c@2 {
 	};
 };
 
-&cpm_mdio {
+&cp0_mdio {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_ge_mdio_pins>;
+	pinctrl-0 = <&cp0_ge_mdio_pins>;
 	status = "okay";
 
 	ge_phy: ethernet-phy@0 {
@@ -167,44 +173,44 @@ ge_phy: ethernet-phy@0 {
 	};
 };
 
-&cpm_pcie0 {
+&cp0_pcie0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_pcie_pins>;
+	pinctrl-0 = <&cp0_pcie_pins>;
 	num-lanes = <4>;
 	num-viewport = <8>;
-	reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_LOW>;
+	reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
-&cpm_pinctrl {
-	cpm_ge_mdio_pins: ge-mdio-pins {
+&cp0_pinctrl {
+	cp0_ge_mdio_pins: ge-mdio-pins {
 		marvell,pins = "mpp32", "mpp34";
 		marvell,function = "ge";
 	};
-	cpm_i2c1_pins: i2c1-pins {
+	cp0_i2c1_pins: i2c1-pins {
 		marvell,pins = "mpp35", "mpp36";
 		marvell,function = "i2c1";
 	};
-	cpm_i2c0_pins: i2c0-pins {
+	cp0_i2c0_pins: i2c0-pins {
 		marvell,pins = "mpp37", "mpp38";
 		marvell,function = "i2c0";
 	};
-	cpm_xhci_vbus_pins: xhci0-vbus-pins {
+	cp0_xhci_vbus_pins: xhci0-vbus-pins {
 		marvell,pins = "mpp47";
 		marvell,function = "gpio";
 	};
-	cpm_pcie_pins: pcie-pins {
+	cp0_pcie_pins: pcie-pins {
 		marvell,pins = "mpp52";
 		marvell,function = "gpio";
 	};
-	cpm_sdhci_pins: sdhci-pins {
+	cp0_sdhci_pins: sdhci-pins {
 		marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
 			       "mpp60", "mpp61";
 		marvell,function = "sdio";
 	};
 };
 
-&cpm_xmdio {
+&cp0_xmdio {
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
@@ -218,83 +224,83 @@ phy8: ethernet-phy@8 {
 	};
 };
 
-&cpm_ethernet {
+&cp0_ethernet {
 	status = "okay";
 };
 
-&cpm_eth0 {
+&cp0_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy0>;
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cpm_comphy4 0>;
+	phys = <&cp0_comphy4 0>;
 };
 
-&cpm_sata0 {
+&cp0_sata0 {
 	/* CPM Lane 0 - U29 */
 	status = "okay";
 };
 
-&cpm_sdhci0 {
+&cp0_sdhci0 {
 	/* U6 */
 	broken-cd;
 	bus-width = <4>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_sdhci_pins>;
+	pinctrl-0 = <&cp0_sdhci_pins>;
 	status = "okay";
 	vqmmc-supply = <&v_3_3>;
 };
 
-&cpm_usb3_0 {
+&cp0_usb3_0 {
 	/* J38? - USB2.0 only */
 	status = "okay";
 };
 
-&cpm_usb3_1 {
+&cp0_usb3_1 {
 	/* J38? - USB2.0 only */
 	status = "okay";
 };
 
-&cps_ethernet {
+&cp1_ethernet {
 	status = "okay";
 };
 
-&cps_eth0 {
+&cp1_eth0 {
 	status = "okay";
 	/* Network PHY */
 	phy = <&phy8>;
 	phy-mode = "10gbase-kr";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cps_comphy4 0>;
+	phys = <&cp1_comphy4 0>;
 };
 
-&cps_eth1 {
+&cp1_eth1 {
 	/* CPS Lane 0 - J5 (Gigabit RJ45) */
 	status = "okay";
 	/* Network PHY */
 	phy = <&ge_phy>;
 	phy-mode = "sgmii";
 	/* Generic PHY, providing serdes lanes */
-	phys = <&cps_comphy0 1>;
+	phys = <&cp1_comphy0 1>;
 };
 
-&cps_pinctrl {
-	cps_spi1_pins: spi1-pins {
+&cp1_pinctrl {
+	cp1_spi1_pins: spi1-pins {
 		marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16";
 		marvell,function = "spi1";
 	};
 };
 
-&cps_sata0 {
+&cp1_sata0 {
 	/* CPS Lane 1 - U32 */
 	/* CPS Lane 3 - U31 */
 	status = "okay";
 };
 
-&cps_spi1 {
+&cp1_spi1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&cps_spi1_pins>;
+	pinctrl-0 = <&cp1_spi1_pins>;
 	status = "okay";
 
 	spi-flash@0 {
@@ -304,7 +310,7 @@ spi-flash@0 {
 	};
 };
 
-&cps_usb3_0 {
+&cp1_usb3_0 {
 	/* CPS Lane 2 - CON7 */
 	usb-phy = <&usb3h0_phy>;
 	status = "okay";

arch/arm64/boot/dts/marvell/armada-8040.dtsi

@@ -59,6 +59,6 @@ / {
  * disable it. However, the RTC clock in CP slave is connected to the
  * oscillator so this one is let enabled.
  */
-&cpm_rtc {
+&cp0_rtc {
 	status = "disabled";
 };

arch/arm64/boot/dts/marvell/armada-80x0.dtsi

@@ -44,34 +44,77 @@
  * Device Tree file for the Armada 80x0 SoC family
  */
 
-#include "armada-cp110-master.dtsi"
-#include "armada-cp110-slave.dtsi"
-
 / {
 	aliases {
-		gpio1 = &cps_gpio1;
-		gpio2 = &cpm_gpio2;
+		gpio1 = &cp1_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+		spi3 = &cp1_spi0;
+		spi4 = &cp1_spi1;
 	};
 };
 
+/*
+ * Instantiate the master CP110
+ */
+#define CP110_NAME		cp0
+#define CP110_BASE		f2000000
+#define CP110_PCIE_IO_BASE	0xf9000000
+#define CP110_PCIE_MEM_BASE	0xf6000000
+#define CP110_PCIE0_BASE	f2600000
+#define CP110_PCIE1_BASE	f2620000
+#define CP110_PCIE2_BASE	f2640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
+/*
+ * Instantiate the slave CP110
+ */
+#define CP110_NAME		cp1
+#define CP110_BASE		f4000000
+#define CP110_PCIE_IO_BASE	0xfd000000
+#define CP110_PCIE_MEM_BASE	0xfa000000
+#define CP110_PCIE0_BASE	f4600000
+#define CP110_PCIE1_BASE	f4620000
+#define CP110_PCIE2_BASE	f4640000
+
+#include "armada-cp110.dtsi"
+
+#undef CP110_NAME
+#undef CP110_BASE
+#undef CP110_PCIE_IO_BASE
+#undef CP110_PCIE_MEM_BASE
+#undef CP110_PCIE0_BASE
+#undef CP110_PCIE1_BASE
+#undef CP110_PCIE2_BASE
+
 /* The 80x0 has two CP blocks, but uses only one block from each. */
-&cps_gpio1 {
+&cp1_gpio1 {
 	status = "okay";
 };
 
-&cpm_gpio2 {
+&cp0_gpio2 {
 	status = "okay";
 };
 
-&cpm_syscon0 {
-	cpm_pinctrl: pinctrl {
-		compatible = "marvell,armada-8k-cpm-pinctrl";
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,armada-8k-cp0-pinctrl";
 	};
 };
 
-&cps_syscon0 {
-	cps_pinctrl: pinctrl {
-		compatible = "marvell,armada-8k-cps-pinctrl";
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
+		compatible = "marvell,armada-8k-cp1-pinctrl";
 
 		nand_pins: nand-pins {
 			marvell,pins =
@@ -91,3 +134,14 @@ nand_rb: nand-rb {
 		};
 	};
 };
+
+&cp1_crypto {
+	/*
+	 * The cryptographic engine found on the cp110
+	 * master is enabled by default at the SoC
+	 * level. Because it is not possible as of now
+	 * to enable two cryptographic engines in
+	 * parallel, disable this one by default.
+	 */
+	status = "disabled";
+};

arch/arm64/boot/dts/marvell/armada-ap806.dtsi

@@ -58,6 +58,7 @@ aliases {
 		serial0 = &uart0;
 		serial1 = &uart1;
 		gpio0 = &ap_gpio;
+		spi0 = &spi0;
 	};
 
 	psci {
@@ -203,7 +204,6 @@ spi0: spi@510600 {
 				reg = <0x510600 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				cell-index = <0>;
 				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&ap_clk 3>;
 				status = "disabled";
@@ -241,7 +241,7 @@ uart1: serial@512100 {
 
 			};
 
-			watchdog: watchdog@600000 {
+			watchdog: watchdog@610000 {
 				compatible = "arm,sbsa-gwdt";
 				reg = <0x610000 0x1000>, <0x600000 0x1000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -286,9 +286,9 @@ ap_gpio: gpio@1040 {
 				};
 			};
 
-			ap_thermal: thermal@6f808C {
+			ap_thermal: thermal@6f808c {
 				compatible = "marvell,armada-ap806-thermal";
-				reg = <0x6f808C 0x4>,
+				reg = <0x6f808c 0x4>,
 				      <0x6f8084 0x8>;
 			};
 		};

arch/arm64/boot/dts/marvell/armada-common.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ */
+
+/* Common definitions used by Armada 7K/8K DTs */
+#define PASTER(x, y) x ## y
+#define EVALUATOR(x, y) PASTER(x, y)
+#define CP110_LABEL(name) EVALUATOR(CP110_NAME, EVALUATOR(_, name))
+#define ADDRESSIFY(addr) EVALUATOR(0x, addr)