Skip to content

L
linux
Commit c3a66272 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge tag 'amlogic-dt64-2' of... 

Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/late

Pull "Amlogic 64-bit DT changes for v4.9, round 2" from Kevin Hilman:

Primarily adding support for newly added drivers

- USB host
- I2C
- SPI flash controller
- PWM
- mailbox, MHU
- pinctrl: add pins for SPI, I2C, SDIO

and then enabling these drivers on various boards.

* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ARM64: dts: meson-gxbb-p20x: Enable USB Nodes
  ARM64: dts: meson-gxbb: add USB Nodes
  ARM64: dts: gxbb: add i2c bus
  ARM64: dts: meson-gxbb: add I2C nodes
  ARM64: dts: meson-gxbb: add pins for I2C
  ARM64: dts: meson-gxbb: Add SPIFC node
  ARM64: dts: meson-gxbb: add the SDIO pins
  ARM64: dts: amlogic: add spi nor pins
  ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver
  ARM64: dts: meson-gxbb: Add Meson GXBB PWM Controller nodes
  ARM64: dts: meson-gxbb: Add Meson MHU Node
  ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices
parents 53570cbc e1e4a1a4
Hide whitespace changes
Inline Side-by-side
Showing with 273 additions and 3 deletions
arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
View file @ c3a66272
......@@ -92,3 +92,9 @@ &ir {
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&i2c_A {
status = "okay";
pinctrl-0 = <&i2c_a_pins>;
pinctrl-names = "default";
};
arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts
View file @ c3a66272
......@@ -50,3 +50,9 @@ / {
compatible = "amlogic,p200", "amlogic,meson-gxbb";
model = "Amlogic Meson GXBB P200 Development Board";
};
&i2c_B {
status = "okay";
pinctrl-0 = <&i2c_b_pins>;
pinctrl-names = "default";
};
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
View file @ c3a66272
......@@ -57,6 +57,19 @@ memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
usb_pwr: regulator-usb-pwrs {
compatible = "regulator-fixed";
regulator-name = "USB_PWR";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
/* signal name in schematic: USB_PWR_EN */
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
/* This UART is brought out to the DB9 connector */
......@@ -77,3 +90,20 @@ &ir {
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_pwr>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
View file @ c3a66272
......@@ -52,6 +52,19 @@ aliases {
chosen {
stdout-path = "serial0:115200n8";
};
usb_vbus: regulator-usb0-vbus {
compatible = "regulator-fixed";
regulator-name = "USB0_VBUS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&uart_AO {
......@@ -66,3 +79,26 @@ &ir {
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&ethmac {
status = "okay";
pinctrl-0 = <&eth_pins>;
pinctrl-names = "default";
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
View file @ c3a66272
......@@ -151,6 +151,25 @@ soc {
#size-cells = <2>;
ranges;
usb0_phy: phy@c0000000 {
compatible = "amlogic,meson-gxbb-usb2-phy";
#phy-cells = <0>;
reg = <0x0 0xc0000000 0x0 0x20>;
resets = <&reset RESET_USB_OTG>;
clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
clock-names = "usb_general", "usb";
status = "disabled";
};
usb1_phy: phy@c0000020 {
compatible = "amlogic,meson-gxbb-usb2-phy";
#phy-cells = <0>;
reg = <0x0 0xc0000020 0x0 0x20>;
clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
clock-names = "usb_general", "usb";
status = "disabled";
};
cbus: cbus@c1100000 {
compatible = "simple-bus";
reg = <0x0 0xc1100000 0x0 0x100000>;
......@@ -180,6 +199,27 @@ uart_B: serial@84dc {
status = "disabled";
};
pwm_ab: pwm@8550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_cd: pwm@8650 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x08650 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
pwm_ef: pwm@86c0 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x086c0 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
uart_C: serial@8700 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x8700 0x0 0x14>;
......@@ -193,6 +233,45 @@ watchdog@98d0 {
reg = <0x0 0x098d0 0x0 0x10>;
clocks = <&xtal>;
};
spifc: spi@8c80 {
compatible = "amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&clkc CLKID_SPI>;
status = "disabled";
};
i2c_A: i2c@8500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x08500 0x0 0x20>;
interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c_B: i2c@87c0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087c0 0x0 0x20>;
interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c_C: i2c@87e0 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087e0 0x0 0x20>;
interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gic: interrupt-controller@c4301000 {
......@@ -244,6 +323,14 @@ mux {
};
};
i2c_ao_pins: i2c_ao {
mux {
groups = "i2c_sck_ao",
"i2c_sda_ao";
function = "i2c_ao";
};
};
pwm_ao_a_3_pins: pwm_ao_a_3 {
mux {
groups = "pwm_ao_a_3";
......@@ -294,6 +381,23 @@ ir: ir@580 {
interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
pwm_ab_AO: pwm@550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x0550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
};
i2c_AO: i2c@500 {
compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x500 0x0 0x20>;
interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc CLKID_AO_I2C>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
periphs: periphs@c8834000 {
......@@ -333,6 +437,16 @@ mux {
};
};
nor_pins: nor {
mux {
groups = "nor_d",
"nor_q",
"nor_c",
"nor_cs";
function = "nor";
};
};
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
......@@ -345,6 +459,25 @@ mux {
};
};
sdio_pins: sdio {
mux {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
"sdio_cmd",
"sdio_clk";
function = "sdio";
};
};
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
function = "sdio";
};
};
uart_a_pins: uart_a {
mux {
groups = "uart_tx_a",
......@@ -369,6 +502,30 @@ mux {
};
};
i2c_a_pins: i2c_a {
mux {
groups = "i2c_sck_a",
"i2c_sda_a";
function = "i2c_a";
};
};
i2c_b_pins: i2c_b {
mux {
groups = "i2c_sck_b",
"i2c_sda_b";
function = "i2c_b";
};
};
i2c_c_pins: i2c_c {
mux {
groups = "i2c_sck_c",
"i2c_sda_c";
function = "i2c_c";
};
};
eth_pins: eth_c {
mux {
groups = "eth_mdio",
......@@ -452,6 +609,15 @@ clkc: clock-controller@0 {
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
mailbox: mailbox@404 {
compatible = "amlogic,meson-gxbb-mhu";
reg = <0 0x404 0 0x4c>;
interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
<0 209 IRQ_TYPE_EDGE_RISING>,
<0 210 IRQ_TYPE_EDGE_RISING>;
#mbox-cells = <1>;
};
};
apb: apb@d0000000 {
......@@ -462,14 +628,40 @@ apb: apb@d0000000 {
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
};
usb0: usb@c9000000 {
compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
reg = <0x0 0xc9000000 0x0 0x40000>;
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
clock-names = "otg";
phys = <&usb0_phy>;
phy-names = "usb2-phy";
dr_mode = "host";
status = "disabled";
};
usb1: usb@c9100000 {
compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
reg = <0x0 0xc9100000 0x0 0x40000>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
clock-names = "otg";
phys = <&usb1_phy>;
phy-names = "usb2-phy";
dr_mode = "host";
status = "disabled";
};
ethmac: ethernet@c9410000 {
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
interrupts = <0 8 1>;
interrupt-names = "macirq";
clocks = <&clkc CLKID_ETH>;
clock-names = "stmmaceth";
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
clock-names = "stmmaceth", "clkin0", "clkin1";
phy-mode = "rgmii";
status = "disabled";
};
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7