- 13 Jun, 2019 1 commit
-
-
Vladimir Oltean authored
The LS1021A-TSN is a development board built by VVDN/Argonboards in partnership with NXP. It features the LS1021A SoC and the first-generation SJA1105T Ethernet switch for prototyping implementations of a subset of IEEE 802.1 TSN standards. It has two regular Ethernet ports and four switched, TSN-capable ports. It also features: - One Arduino header - One expansion header - Two USB 3.0 ports - One mini PCIe slot - One SATA interface - Accelerometer, gyroscope, temperature sensors Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 12 Jun, 2019 5 commits
-
-
Igor Opaniuk authored
Allows to use the SD interface at a higher speed mode if the card supports it. For this the signaling voltage is switched from 3.3V to 1.8V under the usdhc1's drivers control. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Leonard Crestez authored
According to latest docs imx7d chips can go from 800 to 1200 mhz. Maximum frequency is determined from two speed grading bits present in OCOTP fuses at same location as other imx chips. Also update to "typical" voltages from latest datasheet, 25mv higher than current dts. All imx7s parts are still fixed at 800mhz Based on: * IMX7DCEC Rev. 6, 03/2019 * IMX7SCEC Rev. 6, 03/2019 * IMX7DRM Rev. 1, 01/2018 Page 1102 Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Peter Robinson authored
This updates the WL1831 bluetooth to use the serial serdev driver interface. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Peter Robinson authored
The i2c2 bus has a external plug which enables the easy connection of external "bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards has a pair of on board motion sensors, accelerometer and magnetometer on one chip and gyroscope on another so it makes sense to enable these i2c buses for use. Tested on UDOO Neo Full. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Peter Robinson authored
Use the SPDX License Identifier for GPL-2.0+ OR X11 Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 05 Jun, 2019 1 commit
-
-
Anson Huang authored
On i.MX7D SDB board, SW2 supplies a lot of peripheral devices, its voltage should be fixed at 1.8V. The commit 43967d9b ("ARM: dts: imx7d-sdb: Assign corresponding power supply for LDOs") assigns SW2 as the supplier of vdd1p0d, and when its comsumers pcie-phy/mipi-phy try to set the vdd1p0d to 1.0V, regulator core will also set SW2 to its best(min) voltage to 1.5V, and it will lead to board reset. This patch makes SW2's voltage fixed at 1.8V to avoid this issue. Fixes: 43967d9b ("ARM: dts: imx7d-sdb: Assign corresponding power supply for LDOs") Reported-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 23 May, 2019 5 commits
-
-
Andrey Smirnov authored
Both rev C and rev B of the board come with two QSPI-NOR chips attached to the SoC. Add DT code describing all of this. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Andrey Smirnov authored
UART2 is connected to PTD22/23, not PTD0/1. Fix corresponding pinmux node. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Fabio Estevam <festevam@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Steve Longerbeam authored
Add video capture support from the OV5642 to IPU CSI0 on the i.MX53 SMD. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> [fabio: remove unnecessary 'regulator-always-on' from camera regulators] Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Steve Longerbeam authored
Add video capture_subsystem device node, and include both CSI ports. Prepare for adding sensors by adding the parallel sensor anchor endpoints to the CSI ports. Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Rob Herring authored
While properties and child nodes with the same name are valid DT, the practice is not encouraged. Furthermore, the collision is problematic for YAML encoded DT. Let's just avoid the issue and rename the nodes. Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 20 May, 2019 19 commits
-
-
Anson Huang authored
On i.MX6SX SDB board, vgen6 supplies vdd1p1/vdd2p5 LDO and sw2 supplies vdd3p0 LDO, this patch assigns corresponding power supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log: vdd1p1: supplied by regulator-dummy vdd3p0: supplied by regulator-dummy vdd2p5: supplied by regulator-dummy With this patch, the power supply is more accurate: vdd1p1: supplied by VGEN6 vdd3p0: supplied by SW2 vdd2p5: supplied by VGEN6 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX6SLL EVK board, sw2 supplies vdd3p0 LDO, this patch assigns corresponding power supply for vdd3p0 to avoid confusion by below log: vdd3p0: supplied by regulator-dummy With this patch, the power supply is more accurate: vdd3p0: supplied by SW2 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX6SL EVK board, sw2 supplies vdd1p1/vdd2p5/vdd3p0 LDO, this patch assigns corresponding power supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log: vdd1p1: supplied by regulator-dummy vdd3p0: supplied by regulator-dummy vdd2p5: supplied by regulator-dummy With this patch, the power supply is more accurate: vdd1p1: supplied by SW2 vdd3p0: supplied by SW2 vdd2p5: supplied by SW2 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX7D SDB board, sw2 supplies 1p0d/1p2 LDO, this patch assigns corresponding power supply for 1p0d/1p2 LDO to avoid confusion by below log: vdd1p0d: supplied by regulator-dummy vdd1p2: supplied by regulator-dummy With this patch, the power supply is more accurate: vdd1p0d: supplied by SW2 vdd1p2: supplied by SW2 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
On i.MX6Q/DL SabreSD board, vgen5 supplies vdd1p1/vdd2p5 LDO and sw2 supplies vdd3p0 LDO, this patch assigns corresponding power supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log: vdd1p1: supplied by regulator-dummy vdd3p0: supplied by regulator-dummy vdd2p5: supplied by regulator-dummy With this patch, the power supply is more accurate: vdd1p1: supplied by VGEN5 vdd3p0: supplied by SW2 vdd2p5: supplied by VGEN5 Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
Add clock-frequency property to CPU node. Avoids warnings like "/cpus/cpu@0 missing clock-frequency property" for "arm,cortex-a7". Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
This patch adds i.MX7ULP EVK board MIPI-DSI backlight support. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
Add i.MX7ULP EVK board PWM support. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Leo Yan authored
CoreSight DT bindings have been updated, thus the old compatible strings are obsolete and the drivers will report warning if DTS uses these obsolete strings. This patch switches to the new bindings for CoreSight dynamic funnel and static replicator, so can dismiss warning during initialisation. Cc: Shawn Guo <shawnguo@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Fabio Estevam <festevam@gmail.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Update pinmux settings according to hardware team input. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Add meaningful GPIO line names for the board GPIOs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Add GPIO beeper, to let the board produce beeps. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Add GPIO power button and GPIO poweroff, which is present on new hardware. These let the system power itself off on shutdown. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
The yellow LED is in the ethernet jack socket, bind it to netdev trigger to indicate ethernet activity. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Add ethernet PHY GPIO reset line, to let the kernel to reset the PHY. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Turn USBH1 into Host and update the GPIO polarity of the regulator to match new hardware. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Marek Vasut authored
Enable flow control lines on UART1 and UART2, add matching pinmux entries. Add and enable UART3 with RS485 mode enabled on boot. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> To: linux-arm-kernel@lists.infradead.org Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
i.MX6Q/DL's WDOGs use IMX6QDL_CLK_IPG as clock root, assign IMX6QDL_CLK_IPG to them instead of IMX6QDL_CLK_DUMMY. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
Anson Huang authored
i.MX6SL's KPP and WDOG use IMX6SL_CLK_IPG as clock root, assign IMX6SL_CLK_IPG to them instead of IMX6SL_CLK_DUMMY. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-
- 19 May, 2019 9 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifsLinus Torvalds authored
Pull UBIFS fixes from Richard Weinberger: - build errors wrt xattrs - mismerge which lead to a wrong Kconfig ifdef - missing endianness conversion * tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: ubifs: Convert xattr inum to host order ubifs: Use correct config name for encryption ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
-
Linus Torvalds authored
Merge yet more updates from Andrew Morton: "A few final bits: - large changes to vmalloc, yielding large performance benefits - tweak the console-flush-on-panic code - a few fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: panic: add an option to replay all the printk message in buffer initramfs: don't free a non-existent initrd fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro mm/vmalloc.c: keep track of free blocks for vmap allocation
-
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuildLinus Torvalds authored
Pull more Kbuild updates from Masahiro Yamada: - remove unneeded use of cc-option, cc-disable-warning, cc-ldoption - exclude tracked files from .gitignore - re-enable -Wint-in-bool-context warning - refactor samples/Makefile - stop building immediately if syncconfig fails - do not sprinkle error messages when $(CC) does not exist - move arch/alpha/defconfig to the configs subdirectory - remove crappy header search path manipulation - add comment lines to .config to clarify the end of menu blocks - check uniqueness of module names (adding new warnings intentionally) * tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits) kconfig: use 'else ifneq' for Makefile to improve readability kbuild: check uniqueness of module names kconfig: Terminate menu blocks with a comment in the generated config kbuild: add LICENSES to KBUILD_ALLDIRS kbuild: remove 'addtree' and 'flags' magic for header search paths treewide: prefix header search paths with $(srctree)/ media: prefix header search paths with $(srctree)/ media: remove unneeded header search paths alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig kbuild: terminate Kconfig when $(CC) or $(LD) is missing kbuild: turn auto.conf.cmd into a mandatory include file .gitignore: exclude .get_maintainer.ignore and .gitattributes kbuild: add all Clang-specific flags unconditionally kbuild: Don't try to add '-fcatch-undefined-behavior' flag kbuild: add some extra warning flags unconditionally kbuild: add -Wvla flag unconditionally arch: remove dangling asm-generic wrappers samples: guard sub-directories with CONFIG options kbuild: re-enable int-in-bool-context warning MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux* ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c updates from Wolfram Sang: "Some I2C core API additions which are kind of simple but enhance error checking for users a lot, especially by returning errno now. There are wrappers to still support the old API but it will be removed once all users are converted" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: core: add device-managed version of i2c_new_dummy i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Some bug fixes, and an update to the URL's for the final version of Unicode 12.1.0" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: avoid panic during forced reboot due to aborted journal ext4: fix block validity checks for journal inodes using indirect blocks unicode: update to Unicode 12.1.0 final unicode: add missing check for an error return from utf8lookup() ext4: fix miscellaneous sparse warnings ext4: unsigned int compared against zero ext4: fix use-after-free in dx_release() ext4: fix data corruption caused by overlapping unaligned and aligned IO jbd2: fix potential double free ext4: zero out the unused memory region in the extent tree block
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Minor cleanup and fixes, one for stable, four rdma (smbdirect) related. Also adds SEEK_HOLE support" * tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: add support for SEEK_DATA and SEEK_HOLE Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file cifs: Allocate memory for all iovs in smb2_ioctl cifs: Don't match port on SMBDirect transport cifs:smbd Use the correct DMA direction when sending data cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called cifs: use the right include for signal_pending() smb3: trivial cleanup to smb2ops.c cifs: cleanup smb2ops.c and normalize strings smb3: display session id in debug data
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf tooling updates from Ingo Molnar: "perf.data: - Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x perf.data file size reduction on variety of tested workloads what saves storage space on larger server systems where perf.data size can easily reach several tens or even hundreds of GiBs, especially when profiling with DWARF-based stacks and tracing of context switches. perf record: - Improve -user-regs/intr-regs suggestions to overcome errors perf annotate: - Remove hist__account_cycles() from callback, speeding up branch processing (perf record -b) perf stat: - Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for both hardware threads in a core. We can already do this with --per-core, but it's often useful to do this together with other metrics that are collected per hardware thread. I.e. now its possible to do this per-event, and have it mixed with other events not aggregated by core. arm64: - Map Brahma-B53 CPUID to cortex-a53 events. - Add Cortex-A57 and Cortex-A72 events. csky: - Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work on the C-SKY arch. x86: - Add support for recording and printing XMM registers, available, for instance, on Icelake. - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support. UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP. Intel PT: - Fix instructions sampling rate. - Timestamp fixes. - Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste the trees, useful for e-mailing" * 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits) perf stat: Support 'percore' event qualifier perf stat: Factor out aggregate counts printing perf tools: Add a 'percore' event qualifier perf docs: Add description for stderr perf intel-pt: Fix sample timestamp wrt non-taken branches perf intel-pt: Fix improved sample timestamp perf intel-pt: Fix instructions sampling rate perf regs x86: Add X86 specific arch__intr_reg_mask() perf parse-regs: Add generic support for arch__intr/user_reg_mask() perf parse-regs: Split parse_regs perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events perf vendor events arm64: Remove [[:xdigit:]] wildcard perf jevents: Remove unused variable perf test zstd: Fixup verbose mode output perf tests: Implement Zstd comp/decomp integration test perf inject: Enable COMPRESSED record decompression perf report: Implement perf.data record decompression perf record: Implement -z,--compression_level[=<n>] option perf report: Add stub processing of compressed events for -D ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull clocksource updates from Ingo Molnar: "Misc clocksource/clockevent driver updates that came in a bit late but are ready for v5.2" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: misc: atmel_tclib: Do not probe already used TCBs clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static clocksource/drivers/tcb_clksrc: Rename the file for consistency clocksource/drivers/timer-atmel-pit: Rework Kconfig option clocksource/drivers/tcb_clksrc: Move Kconfig option ARM: at91: Implement clocksource selection clocksource/drivers/tcb_clksrc: Use tcb as sched_clock clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib ARM: at91: move SoC specific definitions to SoC folder clocksource/drivers/timer-milbeaut: Cleanup common register accesses clocksource/drivers/timer-milbeaut: Add shutdown function clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer clocksource/drivers/tegra: Rework for compensation of suspend time clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804 clocksource/drivers/sun4i: Add a compatible for suniv dt-bindings: timer: Add Allwinner suniv timer
-