- 05 Sep, 2008 7 commits
-
-
Michael Buesch authored
This adds read/write phyops for the LP-PHY and LP-PHY radios. Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Michael Buesch authored
This adds template code for the LP-PHY. No actual functionality is implemented. Signed-off-by:
-
Michael Buesch authored
Sourcecode files for PHY code are named by phy_XXX.{c,h} where XXX is the PHY type. Move the N-PHY code to match the other files. Signed-off-by: -
Michael Buesch authored
This moves the remaining code from phy.c to phy_a.c phy.c is removed. No functional change. Just moving code and removing dead code. Signed-off-by:
-
Luis R. Rodriguez authored
It is obviously good for userspace to know up front which interface modes a given piece of hardware might support (even if adding such an interface might fail later because of concurrency issues), so let's make cfg80211 aware of that. For good measure, disallow adding interfaces in all other modes so drivers don't forget to announce support for one mode when they add it. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
Nick Kossifidis authored
* No code changes... * Split hw.c to multiple files for better maintenance and add some documentation on each file code is going to grow soon (eeprom.c for example is going to get much stuff currently developed on ath_info) so it's better this way. * Rename following functions to maintain naming scheme: ah_setup_xtx_desc -> ah_setup_mrr_tx_desc (Because xtx doesn't say much, it's actually a multi-rate-retry tx descriptor) ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp (We don't put any "buf" we set descriptor pointers on hw) ath5k_hw_tx_start -> ath5k_hw_start_tx_dma ath5k_hw_start_rx -> ath5k_hw_start_rx_dma ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu (It's easier this way to identify them, we also have ath5k_hw_start_rx_pcu which completes the set) ath5k_hw_set_intr -> ath5k_hw_set_imr (As in get_isr we set imr here, not "intr") * Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can include support for different rx descriptors in the future * Further cleanups so that checkpatch doesn't complain (only some > 80 col warnings for eeprom.h and reg.h as usual due to comments) Tested on 5211 and 5213 cards and works ok. Changes-licensed-under: ISC Signed-off-by:Nick Kossifidis <mickflemm@gmail.com> Acked-by:
-
Michael Buesch authored
It is valid to pass &gphy->rfatt and &gphy->bbatt as rfatt and bbatt pointer arguments to the function. So we have to use memmove for the possibly overlapping memory areas. Signed-off-by:
-
- 03 Sep, 2008 33 commits
-
-
Ilpo Järvinen authored
Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Huang Weiyi authored
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. drivers/net/myri10ge/myri10ge.c drivers/net/netxen/netxen_nic_ethtool.c drivers/net/tokenring/lanstreamer.c This patch removes the said #include <version.h>. Signed-off-by:
Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by:
-
Kevin Lo authored
This patch uses netdev_alloc_skb. This sets skb->dev and allows arch specific allocation. Also cleanup the alignment code. Signed-off-by:
Kevin Lo <kevlo@kevlo.org> Signed-off-by:
-
Kevin Lo authored
This patch uses netdev_alloc_skb. This sets skb->dev and allows arch specific allocation. Also cleanup the alignment code. Signed-off-by:
-
Kevin Lo authored
Use netdev_alloc_skb. This sets skb->dev and allows arch specific allocation. Also cleanup the alignment code. Signed-off-by:
-
Stephen Hemminger authored
Change bootup messages to print more information. This is to help users who may have old buggy EEPROM image. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
-
Stephen Hemminger authored
Cleanup and harden the routines accessing the EEPROM. 1. Prevent spin forever waiting for the TWSI bus 2. Fix write eeprom to write full words rather than only 16 bits Luckly the vendor doesn't provide EEPROM in Linux format so it must never have been used. 3. Don't allow partial eeprom writes, not needed, not safe. These are non-urgent bug fixes. Signed-off-by: -
Jeff Garzik authored
Merge branch 'r8169-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6 into upstream-next
-
Alexander Duyck authored
This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue. Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Alexander Duyck authored
Remove code that was in place to support fake netdev Signed-off-by:
-
Alexander Duyck authored
The cleaned variable can be replaced by the count of packets cleaned during the tx interrupt routine so it can be removed. Signed-off-by:
-
Bruce Allan authored
This new part has the same feature set as previous parts with the addition of MSI-X support. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
-
Bruce Allan authored
Add support for new LOM devices on the latest generation ICHx platforms. Signed-off-by:
-
Bruce Allan authored
Enable PCI device ID for a new combination of MAC and PHY already supported in the driver. Signed-off-by:
-
PJ Waskiewicz authored
Change TSO offloads to use a different context than VLAN insertion and Tx checksumming. Hardware has separate registers internally for storing these so use them. Signed-off-by:
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
hardware was configured incorrectly which led all hints to be sent to queue[0]'s DCA configuration. Signed-off-by:
-
Jesse Brandeburg authored
Signed-off-by:
-
Jesse Brandeburg authored
DCA related fixes ================= - ixgbe was not compiling and using DCA correctly if dca was a module - DCA interface changed with new kernel - ixgbe was not correctly configured to indicate DCA hints to the correct CPU. Signed-off-by:
-
Jesse Brandeburg authored
as mentioned by Herbert, our hardware supports IP offloads, not full checksum offloads for any protocol in existence (even though the hardware just provides generic csum support over any range of bytes) Signed-off-by:
-
Jesse Brandeburg authored
This locks the seed down so loading/unloading the driver will present predictable hashing from RSS. Also move the rx_buf_len out of the adapter struct, and into the Rx ring struct. Signed-off-by:
-
Jesse Brandeburg authored
Enable Tx Head Writeback in the hardware. This helps performance by removing adapter writebacks to descriptors on transmit completion. Signed-off-by:
-
Jesse Brandeburg authored
Since the adapter cannot tell what the remote end's flow control capability is through auto-neg, we must turn off flow control by default. Signed-off-by:
-
Jesse Brandeburg authored
Cleanup all the different references to the Tx ring and Rx ring structures and make them common across the driver. Signed-off-by:
-
Jesse Brandeburg authored
Signed-off-by:
-
Christopher Leech authored
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists. Signed-off-by:
Christopher Leech <christopher.leech@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
Signed-off-by:
-
Jesse Brandeburg authored
the driver was misinterpreting rx_csum return value in the descriptor so occassionally we would indicate an rx_csum error in our stats when there was none. This would have no effect on traffic because we would just hand the packet to the stack anyway without the offload flag set, but would increase CPU for those packets that needed a recompute. Signed-off-by:
-
roel kluin authored
MAL[12]_IER_EVENTS definitions have MAL_IER_OTE twice but lack MAL_IER_DE Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Randy Dunlap authored
Fix hp-plus Makefile object file: drivers/built-in.o: In function `hpp_open': hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt' hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open' drivers/built-in.o: In function `hpp_close': hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close' drivers/built-in.o: In function `hpp_probe1': hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll' drivers/built-in.o: In function `hp_plus_probe': (.init.text+0x7407): undefined reference to `__alloc_ei_netdev' make[1]: *** [.tmp_vmlinux1] Error 1 Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Brian Haley authored
Resending since I didn't see any responses from the first try. Change __constant_htons() to htons() in the bonding driver, it should only be used for initializers. -Brian Signed-off-by:
Brian Haley <brian.haley@hp.com> Signed-off-by:
-
Ben Hutchings authored
When !port_enabled, defer the write to reconfigure_mac_wrapper. Whilst here, simplify the logic now that efx_start_port() always calls efx_reconfigure_port(). From: Steve Hodgson <shodgson@solarflare.com> Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Ben Hutchings authored
This was originally a kludge to fix broken locking, which has since been fixed properly. Signed-off-by:
-
Ben Hutchings authored
Include PMA/PMD in loopback self-tests as intended. Add NVRAM checksum validation and include it in self-tests. Add register self-tests. Run PHY self-tests where available. Signed-off-by:
-
