- 03 Dec, 2016 7 commits
-
-
Jacob Keller authored
A comment incorrectly referred to i40e_vsi_sync_filters_subtask which does not actually exist. Reference the correct function instead. Change-ID: I6bd805c605741ffb6fe34377259bb0d597edfafd Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Michal Kosiarz authored
Some external PHYs require Clause22 method for accessing registers. This patch also adds some defines to support blink led on devices using 10CBaseT PHY. Change-ID: I868a4326911900f6c89e7e522fda4968b0825f14 Signed-off-by:
Michal Kosiarz <michal.kosiarz@intel.com> Signed-off-by:
Matt Jared <matthew.a.jared@intel.com> Tested-by:
-
Jacob Keller authored
Separate the global private flags and the regular private flags per interface into two arrays. Future additions of private flags will not need to be duplicated which may lead to buggy code. Also rename "i40e_priv_flags_strings_gl" to "i40e_gl_priv_flags_strings" for clarity, as it reads more naturally. Change-ID: I68caef3c9954eb7da342d7f9d20f2873186f2758 Signed-off-by:
-
Jacob Keller authored
Replace a check of magic number 4095 with VLAN_N_VID. This makes it obvious that a later check against VLAN_N_VID is always true and can be removed. Change-ID: I28998f127a61a529480ce63d8a07e266f6c63b7b Signed-off-by:
-
Jacob Keller authored
This label is unnecessary, as are jumping to a block that checks aq_ret and then immediately skipping it and returning. So just jump straight to the error_param and remove this unnecessary label. Also use goto error_param even in the last check for style consistency. Change-ID: If487c7d10c4048e37c594e5eca167693aaed45f6 Signed-off-by:
-
Alexander Duyck authored
This change makes it so that we are much more robust about defining what we can and cannot offload. Previously we were performing no checks. This should bring us up to parity with the i40e PF driver. In addition the device only supports GSO as long as the MSS is 64 or greater. We were not checking this so an MSS less than that was resulting in Tx hangs. Change-ID: If533553ec92fc6ba694eab6ac81fdaf3004f3592 Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Alexander Duyck authored
This change makes it so that we are much more robust about defining what we can and cannot offload. Previously we were just checking for the L4 tunnel header length, however there are other fields we should be verifying as there are multiple scenarios in which we cannot perform hardware offloads. In addition the device only supports GSO as long as the MSS is 64 or greater. We were not checking this so an MSS less than that was resulting in Tx hangs. Change-ID: I5e2fd5f3075c73601b4b36327b771c64fcb6c31b Signed-off-by:
-
- 02 Dec, 2016 33 commits
-
-
David S. Miller authored
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.10 Major changes: rsi * filter rx frames * configure tx power * make it possible to select antenna * support 802.11d brcmfmac * cleanup of scheduled scan code * support for bcm43341 chipset with different chip id * support rev6 of PCIe device interface ath10k * add spectral scan support for QCA6174 and QCA9377 families * show used tx bitrate with 10.4 firmware wil6210 * add power save mode support * add abort scan functionality * add support settings retry limit for short frames bcma * add Dell Inspiron 3148 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Gregory CLEMENT says: ==================== Support Armada 37xx SoC (ARMv8 64-bits) in mvneta driver The Armada 37xx is a new ARMv8 SoC from Marvell using same network controller as the older Armada 370/38x/XP SoCs. This series adapts the driver in order to be able to use it on this new SoC. The main changes are: - 64-bits support: the first patches allow using the driver on a 64-bit architecture. - MBUS support: the mbus configuration is different on Armada 37xx from the older SoCs. - per cpu interrupt: Armada 37xx do not support per cpu interrupt for the NETA IP, the non-per-CPU behavior was added back. The first patch is an optimization in the rx path in swbm mode. The second patch remove unnecessary allocation for HWBM. The first item is solved by patches 4 and 5. The 2 last items are solved by patch 6. In patch 7 the dt support is added. Beside Armada 37xx, this series have been again tested on Armada XP and Armada 38x (with Hardware Buffer Management and with Software Buffer Management). This is the 6th version of the series: - 1st version: http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/469588.html - 2nd version: http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470476.html - 3rd version: http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470901.html - 4th version: http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/471039.html - 5th version: http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/471478.html Changelog: v5 -> v6: - Added Tested-by from Marcin Wojtas on the series - Added Reviewed-by from Jisheng Zhang on patch 3 - Fix eth1 phy mode for Armada 3720 DB board on patch 7 v4 -> v5: - remove unnecessary cast in patch 3 v3 -> v4: - Adding new patch: "net: mvneta: do not allocate buffer in rxq init with HWBM" - Simplify the HWBM case in patch 3 as suggested by Marcin v2 -> v3: - Adding patch 1 "Optimize rx path for small frame" - Fix the kbuild error by moving the "phys_addr += pp->rx_offset_correction;" line from patch 2 to patch 3 where rx_offset_correction is introduced. - Move the memory allocation of the buf_virt_addr of the rxq to be called by the probe function in order to avoid a memory leak. ==================== Signed-off-by:
-
Gregory CLEMENT authored
Add neta nodes for network support both in device tree for the SoC and the board. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Marcin Wojtas authored
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller as older Armada 370/38x/XP. There are however some differences that needed taking into account when adding support for it: * open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus configuration for network controller has to be done on two levels: global and per-port. The first one is inherited from the bootloader. The latter can be opened in a default way, leaving arbitration to the bus controller. Hence filled mbus_dram_target_info structure is not needed * make per-CPU operation optional - Recent patches adding RSS and XPS support for Armada 38x/XP enabled per-CPU operation of the controller by default. Contrary to older SoC's Armada 3700 SoC's network controller is not capable of per-CPU processing due to interrupt lines' connectivity. This patch restores non-per-CPU operation, which is now optional and depends on neta_armada3700 flag value in mvneta_port structure. In order not to complicate the code, separate interrupt subroutine is implemented. For now, on the Armada 3700, RSS is disabled as the current implementation depend on the per cpu interrupts. [gregory.clement@free-electrons.com: extract from a larger patch, replace some ifdef and port to net-next for v4.10] Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Signed-off-by:
-
Gregory CLEMENT authored
Actually only the mvneta_bm support is not 64-bits compatible. The mvneta code itself can run on 64-bits architecture. Signed-off-by:
-
Marcin Wojtas authored
Prepare the mvneta driver in order to be usable on the 64 bits platform such as the Armada 3700. [gregory.clement@free-electrons.com]: this patch was extract from a larger one to ease review and maintenance. Signed-off-by:
-
Gregory CLEMENT authored
Until now the virtual address of the received buffer were stored in the cookie field of the rx descriptor. However, this field is 32-bits only which prevents to use the driver on a 64-bits architecture. With this patch the virtual address is stored in an array not shared with the hardware (no more need to use the DMA API). Thanks to this, it is possible to use cache contrary to the access of the rx descriptor member. The change is done in the swbm path only because the hwbm uses the cookie field, this also means that currently the hwbm is not usable in 64-bits. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Tested-by:
-
Gregory CLEMENT authored
For HWBM all buffers are allocated in mvneta_bm_construct() and in runtime they are put into descriptors by hardware. There is no need to fill them at this point. Suggested-by:
-
Gregory CLEMENT authored
For small frame reuse the phys_addr variable instead of accessing the uncacheable value in the rx descriptor. Signed-off-by:
-
David S. Miller authored
David Ahern says: ==================== net: Add bpf support for sockets The recently added VRF support in Linux leverages the bind-to-device API for programs to specify an L3 domain for a socket. While SO_BINDTODEVICE has been around for ages, not every ipv4/ipv6 capable program has support for it. Even for those programs that do support it, the API requires processes to be started as root (CAP_NET_RAW) which is not desirable from a general security perspective. This patch set leverages Daniel Mack's work to attach bpf programs to a cgroup to provide a capability to set sk_bound_dev_if for all AF_INET{6} sockets opened by a process in a cgroup when the sockets are allocated. For example: 1. configure vrf (e.g., using ifupdown2) auto eth0 iface eth0 inet dhcp vrf mgmt auto mgmt iface mgmt vrf-table auto 2. configure cgroup mount -t cgroup2 none /tmp/cgroupv2 mkdir /tmp/cgroupv2/mgmt test_cgrp2_sock /tmp/cgroupv2/mgmt 15 3. set shell into cgroup (e.g., can be done at login using pam) echo $$ >> /tmp/cgroupv2/mgmt/cgroup.procs At this point all commands run in the shell (e.g, apt) have sockets automatically bound to the VRF (see output of ss -ap 'dev == <vrf>'), including processes not running as root. This capability enables running any program in a VRF context and is key to deploying Management VRF, a fundamental configuration for networking gear, with any Linux OS installation. This patchset also exports the socket family, type and protocol as read-only allowing bpf filters to deny a process in a cgroup the ability to open specific types of AF_INET or AF_INET6 sockets. v7 - comments from Alexei v6 - add export of socket family, type and protocol ==================== Signed-off-by: -
David Ahern authored
Add examples preventing a process in a cgroup from opening a socket based family, protocol and type. Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
David Ahern authored
Add support for section names starting with cgroup/skb and cgroup/sock. Signed-off-by:
-
David Ahern authored
Add socket family, type and protocol to bpf_sock allowing bpf programs read-only access. Add __sk_flags_offset[0] to struct sock before the bitfield to programmtically determine the offset of the unsigned int containing protocol and type. Signed-off-by:
-
David Ahern authored
Add a simple program to demonstrate the ability to attach a bpf program to a cgroup that sets sk_bound_dev_if for AF_INET{6} sockets when they are created. Signed-off-by: -
David Ahern authored
Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run any time a process in the cgroup opens an AF_INET or AF_INET6 socket. Currently only sk_bound_dev_if is exported to userspace for modification by a bpf program. This allows a cgroup to be configured such that AF_INET{6} sockets opened by processes are automatically bound to a specific device. In turn, this enables the running of programs that do not support SO_BINDTODEVICE in a specific VRF context / L3 domain. Signed-off-by: -
David Ahern authored
Code move and rename only; no functional change intended. Signed-off-by:
-
Eric Dumazet authored
My recent commit to get more precise rx/tx counters in ndo_get_stats64() can lead to crashes at device dismantle, as Jesper found out. We must prevent mlx4_en_fold_software_stats() trying to access tx/rx rings if they are deleted. Fix this by adding a test against priv->port_up in mlx4_en_fold_software_stats() Calling mlx4_en_fold_software_stats() from mlx4_en_stop_port() allows us to eventually broadcast the latest/current counters to rtnetlink monitors. Fixes: 40931b85 ("mlx4: give precise rx/tx bytes/packets counters") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-and-bisected-by:
Jesper Dangaard Brouer <brouer@redhat.com> Tested-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Sunil Goutham authored
Transmit queue timeout issue is seen in two cases - Due to a race condition btw setting stop_queue at xmit() and checking for stopped_queue in NAPI poll routine, at times transmission from a SQ comes to a halt. This is fixed by using barriers and also added a check for SQ free descriptors, incase SQ is stopped and there are only CQE_RX i.e no CQE_TX. - Contrary to an assumption, a HW errata where HW doesn't stop transmission even though there are not enough CQEs available for a CQE_TX is not fixed in T88 pass 2.x. This results in a Qset error with 'CQ_WR_FULL' stalling transmission. This is fixed by adjusting RXQ's RED levels for CQ level such that there is always enough space left for CQE_TXs. Signed-off-by:
Sunil Goutham <sgoutham@cavium.com> Signed-off-by:
-
David S. Miller authored
Hadar Hen Zion says: ==================== Offloading tc rules using underline Hardware device This series adds flower classifier support in offloading tc rules when the Software ingress device is different from the Hardware ingress device, such as when dealing with IP tunnels The first two patches are a small fixes to flower, checking the skip_hw flag wasn't set before calling the Hardware offloading functions which will try to offload the rule. The next two patches are infrastructure patches, a preparation for the fourth patch which is adding support in flower to offload rules when the ingress device is not a Hardware device and therefore can't offload. In this case ndo_setup_tc is called with the mirred (egress) device. The last three patchs are adding mlx5e support to offload rules using the new "egress_device" flag. Thanks, Hadar Changes from v0: - check if CONFIG_NET_CLS_ACT is defined befor calling tc_action_ops get_dev() ==================== Signed-off-by: -
Hadar Hen Zion authored
When ndo_setup_tc is called with an egress_dev flag set, it means that the ndo call was executed on the mirred action (egress) device and not on the ingress device. In order to support this kind of ndo_setup_tc call, and insert the correct decap rule to the hardware, the uplink device on the same eswitch should be found. Currently, we use this resolution between the mirred device and the uplink on the same eswitch to offload vxlan shared device decap rules. Signed-off-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
-
Hadar Hen Zion authored
Replace the representor private data to a net_device pointer holding the representor netdevice, instead of void pointer holding mlx5e_priv. It will be used by a new eswitch service function, returning the uplink representor netdevice. Signed-off-by:
-
Hadar Hen Zion authored
The VF Representor udp tunnel ndo entries were removed by mistake, return them. Fixes: 370bad0f ('net/mlx5e: Support HW (offloaded) and SW counters for SRIOV switchdev mode') Signed-off-by:
-
Hadar Hen Zion authored
In order to support hardware offloading when the device given by the tc rule is different from the Hardware underline device, extract the mirred (egress) device from the tc action when a filter is added, using the new tc_action_ops, get_dev(). Flower caches the information about the mirred device and use it for calling ndo_setup_tc in filter change, update stats and delete. Calling ndo_setup_tc of the mirred (egress) device instead of the ingress device will allow a resolution between the software ingress device and the underline hardware device. The resolution will take place inside the offloading driver using 'egress_device' flag added to tc_to_netdev struct which is provided to the offloading driver. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Hadar Hen Zion authored
Adding support to a new tc_action_ops. get_dev is a general option which allows to get the underline device when trying to offload a tc rule. In case of mirred action the returned device is the mirred (egress) device. Signed-off-by:
-
Hadar Hen Zion authored
Instead of providing many arguments to fl_hw_{replace/destroy}_filter functions, just provide cls_fl_filter struct that includes all the relevant args. This patches doesn't add any new functionality. Signed-off-by: -
Hadar Hen Zion authored
Check skip_hw flag isn't set before calling fl_hw_{replace/destroy}_filter and fl_hw_update_stats functions. Replace the call to tc_should_offload with tc_can_offload. tc_can_offload only checks if the device supports offloading, the check for skip_hw flag is done earlier in the flow. Signed-off-by: -
Hadar Hen Zion authored
Creating a difference between two possible cases: 1. Not offloading tc rule since the user sets 'skip_hw' flag. 2. Not offloading tc rule since the device doesn't support offloading. This patch doesn't add any new functionality. Signed-off-by:
-
Florian Westphal authored
Eric says: "By looking at tcpdump, and TS val of xmit packets of multiple flows, we can deduct the relative qdisc delays (think of fq pacing). This should work even if we have one flow per remote peer." Having random per flow (or host) offsets doesn't allow that anymore so add a way to turn this off. Suggested-by:
Florian Westphal <fw@strlen.de> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Florian Westphal authored
jiffies based timestamps allow for easy inference of number of devices behind NAT translators and also makes tracking of hosts simpler. commit ceaa1fef ("tcp: adding a per-socket timestamp offset") added the main infrastructure that is needed for per-connection ts randomization, in particular writing/reading the on-wire tcp header format takes the offset into account so rest of stack can use normal tcp_time_stamp (jiffies). So only two items are left: - add a tsoffset for request sockets - extend the tcp isn generator to also return another 32bit number in addition to the ISN. Re-use of ISN generator also means timestamps are still monotonically increasing for same connection quadruple, i.e. PAWS will still work. Includes fixes from Eric Dumazet. Signed-off-by:
-
David S. Miller authored
Manish Rangankar says: ==================== Add QLogic FastLinQ iSCSI (qedi) driver. This series introduces hardware offload iSCSI initiator driver for the 41000 Series Converged Network Adapters (579xx chip) by Qlogic. The overall driver design includes a common module ('qed') and protocol specific dependent modules ('qedi' for iSCSI). This is an open iSCSI driver, modifications to open iSCSI user components 'iscsid', 'iscsiuio', etc. are required for the solution to work. The user space changes are also in the process of being submitted. https://groups.google.com/forum/#!forum/open-iscsi The 'qed' common module, under drivers/net/ethernet/qlogic/qed/, is enhanced with functionality required for the iSCSI support. This series is based on: net tree base: Merge of net and net-next as of 11/29/2016 Changes from RFC v2: 1. qedi patches are squashed into single patch to prevent krobot warning. 2. Fixed 'hw_p_cpuq' incompatible pointer type. 3. Fixed sparse incompatible types in comparison expression. 4. Misc fixes with latest 'checkpatch --strict' option. 5. Remove int_mode option from MODULE_PARAM. 6. Prefix all MODULE_PARAM params with qedi_*. 7. Use CONFIG_QED_ISCSI instead of CONFIG_QEDI 8. Added bad task mem access fix. ==================== Signed-off-by: -
Yuval Mintz authored
This patch adds out of order packet handling for hardware offloaded iSCSI. Out of order packet handling requires driver buffer allocation and assistance. Signed-off-by:
Arun Easi <arun.easi@cavium.com> Signed-off-by:
Yuval Mintz <yuval.mintz@cavium.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Yuval Mintz authored
This adds the backbone required for the various HW initalizations which are necessary for the iSCSI driver (qedi) for QLogic FastLinQ 4xxxx line of adapters - FW notification, resource initializations, etc. Signed-off-by:
-
Rasmus Villemoes authored
This is already using the %pM printf extension; might as well also use %ph to make the code smaller. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
