The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.

Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Abort failed command from workqueue rather than from an interrupt,
allowing longer delays in abortion.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
solution with no need for locking.

This path also adds some cleanups.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

If the get_cover_state is not set, it occurs the oops.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Using setup_timer() instead of init_timer() on omap.c file.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initialization stream until
the controller starts running again and responds with the end of command
status.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Fix the data timeout calculation for MMC multislot support.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

New functions to support MMC multislot:
mmc_omap_release_dma() and mmc_omap_abort_xfer().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch adds back MMC cover switch support in a way that
supports multiple slots.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Introduce new MMC multislot structure and change driver to use it.

Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch removes the MMC cover switch handling temporarily
to make following multislot patches cleaner.

MMC cover switch handling will be added back in later patches
after adding basic multislot support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

According with commit 255d01af
from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman.
MMC_CAP_BYTEBLOCK is not defined causing the compile error:

drivers/mmc/host/omap.c: In function `mmc_omap_probe':
drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function)
drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once
drivers/mmc/host/omap.c:1077: error: for each function it appears in.)
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

As noted by Kyungmin Park, the divisor calculation has
an unnecessary increase.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch removes some opcodes from host driver so there's no need on putting
'#include <linux/mmc/mmc.h>', that should not be needed in host drivers.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Remove the use of the sdhci specific device name and use the mmc controller
name instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (64 commits)
  ocfs2/net: Add debug interface to o2net
  ocfs2: Only build ocfs2/dlm with the o2cb stack module
  ocfs2/cluster: Get rid of arguments to the timeout routines
  ocfs2: Put tree in MAINTAINERS
  ocfs2: Use BUG_ON
  ocfs2: Convert ocfs2 over to unlocked_ioctl
  ocfs2: Improve rename locking
  fs/ocfs2/aops.c: test for IS_ERR rather than 0
  ocfs2: Add inode stealing for ocfs2_reserve_new_inode
  ocfs2: Add ac_alloc_slot in ocfs2_alloc_context
  ocfs2: Add a new parameter for ocfs2_reserve_suballoc_bits
  ocfs2: Enable cross extent block merge.
  ocfs2: Add support for cross extent block
  ocfs2: Move /sys/o2cb to /sys/fs/o2cb
  sysfs: Allow removal of symlinks in the sysfs root
  ocfs2:  Reconnect after idle time out.
  ocfs2/dlm: Cleanup lockres print
  ocfs2/dlm: Fix lockname in lockres print function
  ocfs2/dlm: Move dlm_print_one_mle() from dlmmaster.c to dlmdebug.c
  ocfs2/dlm: Dumps the purgelist into a debugfs file
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (49 commits)
  [GFS2] fix assertion in log_refund()
  [GFS2] fix GFP_KERNEL misuses
  [GFS2] test for IS_ERR rather than 0
  [GFS2] Invalidate cache at correct point
  [GFS2] fs/gfs2/recovery.c: suppress warnings
  [GFS2] Faster gfs2_bitfit algorithm
  [GFS2] Streamline quota lock/check for no-quota case
  [GFS2] Remove drop of module ref where not needed
  [GFS2] gfs2_adjust_quota has broken unstuffing code
  [GFS2] possible null pointer dereference fixup
  [GFS2] Need to ensure that sector_t is 64bits for GFS2
  [GFS2] re-support special inode
  [GFS2] remove gfs2_dev_iops
  [GFS2] fix file_system_type leak on gfs2meta mount
  [GFS2] Allow bmap to allocate extents
  [GFS2] Fix a page lock / glock deadlock
  [GFS2] proper extern for gfs2/locking/dlm/mount.c:gdlm_ops
  [GFS2] gfs2/ops_file.c should #include "ops_inode.h"
  [GFS2] be*_add_cpu conversion
  [GFS2] Fix bug where we called drop_bh incorrectly
  ...

TF_MASK is no longer defined, use X86_EFLAGS_TF.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (27 commits)
  [IA64] kdump: Add crash_save_vmcoreinfo for INIT
  [IA64] Fix NUMA configuration issue
  [IA64] Itanium Spec updates
  [IA64] Untangle sync_icache_dcache() page size determination
  [IA64] arch/ia64/kernel/: use time_* macros
  [IA64] remove redundant display of free swap space in show_mem()
  [IA64] make IOMMU respect the segment boundary limits
  [IA64] kprobes: kprobe-booster for ia64
  [IA64] fix getpid and set_tid_address fast system calls for pid namespaces
  [IA64] Replace explicit jiffies tests with time_* macros.
  [IA64] use goto to jump out do/while_each_thread
  [IA64] Fix unlock ordering in smp_callin
  [IA64] pgd_offset() constfication.
  [IA64] kdump: crash.c coding style fix
  [IA64] kdump: add kdump_on_fatal_mca
  [IA64] Minimize per_cpu reservations.
  [IA64] Correct pernodesize calculation.
  [IA64] Kernel parameter for max number of concurrent global TLB purges
  [IA64] Multiple outstanding ptc.g instruction support
  [IA64] Implement smp_call_function_mask for ia64
  ...

This patch exposes o2net information via debugfs. The information includes
the list of sockets (sock_containers) as well as the list of outstanding
messages (send_tracking). Useful for o2dlm debugging.

(This patch is derived from an earlier one written by Zach Brown that
exposed the same information via /proc.)

[Mark: checkpatch fixes]
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

fs/ocfs2/dlm/ocfs2_dlm.ko and fs/ocfs2/dlm/ocfs2_dlmfs.ko get built if
CONFIG_FS_OCFS2 is specified. This isn't quite how it should happen any more
- the "o2cb" dlm modules should only be built if CONFIG_FS_OCFS2_O2CB is
set, so update the dlm Makefile accordingly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>

We keep seeing bug reports related to NULL pointer derefs in
o2net_set_nn_state(). When I originally wrote up the configurable timeout
patch, I had tried to plan for multiple clusters. This was silly.

The timeout routines all use o2nm_single_cluster so there's no point in
passing an argument at all. This patch removes the arguments and kills those
bugs dead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

The ocfs2 MAINTAINERS entry should have the git tree URL.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

if (...) BUG(); should be replaced with BUG_ON(...) when the test has no
side-effects to allow a definition of BUG_ON that drops the code completely.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@ disable unlikely @ expression E,f; @@

(
  if (<... f(...) ...>) { BUG(); }
|
- if (unlikely(E)) { BUG(); }
+ BUG_ON(E);
)

@@ expression E,f; @@

(
  if (<... f(...) ...>) { BUG(); }
|
- if (E) { BUG(); }
+ BUG_ON(E);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

As far as I can see there is nothing in ocfs2_ioctl that requires the BKL,
so use unlocked_ioctl
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

ocfs2_rename() was being too aggressive with the rename lock - we only need
it for certain forms of directory rename.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

The function ocfs2_start_trans always returns either a valid pointer or a
value made with ERR_PTR, so its result should be tested with IS_ERR, not
with a test for 0.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

Inode allocation is modified to look in other nodes allocators during
extreme out of space situations. We retry our own slot when space is freed
back to the global bitmap, or whenever we've allocated more than 1024 inodes
from another slot.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

In inode stealing, we no longer restrict the allocation to
happen in the local node. So it is neccessary for us to add
a new member in ocfs2_alloc_context to indicate which slot
we are using for allocation. We also modify the process of
local alloc so that this member can be used there also.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

In some cases(Inode stealing from other nodes), we may not want
ocfs2_reserve_suballoc_bits to allocate new groups from the
global_bitmap since it may already be full. So add a new parameter
for this.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

In ocfs2_figure_merge_contig_type, we judge whether there exists
a cross extent block merge and enable it by setting CONTIG_LEFT
and CONTIG_RIGHT accordingly.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>

In ocfs2_merge_rec_left, when we find the merge extent is "CONTIG_RIGHT"
with the first extent record of the next extent block, we will merge it to
the next extent block and change all the related extent blocks accordingly.

In ocfs2_merge_rec_right, when we find the merge extent is "CONTIG_LEFT"
with the last extent record of the previous extent block, we will merge
it to the prevoius extent block and change all the related extent blocks
accordingly.

As for CONTIG_LEFTRIGHT, we will handle CONTIG_RIGHT first so that when
the index is zero, the merge process will be more efficient and easier.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>