- 28 Jan, 2022 25 commits
-
-
Chen-Yu Tsai authored
Encoders typically operate on macroblocks. Thus their output or coded resolution is constrained to multiples of macroblocks. For frame sizes not aligned to macroblocks, cropping is needed to limit the visible area of the frame. Add support for cropping on the output (source) side for encoders, using the selection API. Signed-off-by:
Chen-Yu Tsai <wenst@chromium.org> Reviewed-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Chen-Yu Tsai authored
The Hantro H1 hardware can crop off pixels from the right and bottom of the source frame. These are controlled with the H1_REG_IN_IMG_CTRL_OVRFLB and H1_REG_IN_IMG_CTRL_OVRFLR in the H1_REG_IN_IMG_CTRL register. The ChromeOS kernel driver that this was based on incorrectly added the _D4 suffix H1_REG_IN_IMG_CTRL_OVRFLB. This field crops the bottom of the input frame, and the number is _not_ divided by 4. [1] Correct the name to avoid confusion when crop support with the selection API is added. [1] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/refs/ \ heads/chromeos-4.19/drivers/staging/media/hantro/hantro_h1_vp8_enc.c#377 Fixes: 775fec69 ("media: add Rockchip VPU JPEG encoder driver") Fixes: a29add8c ("media: rockchip/vpu: rename from rockchip to hantro") Signed-off-by:
-
Benjamin Mugnier authored
Mickael left the company and is not willing to keep maintainership. Add Sylvain and myself as maintainers of mipid02 driver. Signed-off-by:
Benjamin Mugnier <benjamin.mugnier@foss.st.com> Signed-off-by:
-
Christophe JAILLET authored
No concurrent access is possible when a bitmap is local to a function. So prefer the non-atomic '__[set|clear]_bit()' functions to save a few cycles. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Martin Kepplinger authored
Add the fsl,imx8mq-csi compatible string to the bindings for nxp,imx7-csi. The i.MX8MQ SoC contains the same CSI bridge controller as the i.MX7. Signed-off-by:
Martin Kepplinger <martin.kepplinger@puri.sm> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Martin Kepplinger authored
Modeled after the NXP driver mx6s_capture.c that this driver is based on, imx8mq needs different settings for the baseaddr_switch mechanism. Define the needed bits and set that for imx8mq. Without these settings, the system will "sometimes" hang completely when starting to stream (the interrupt will never be called). Signed-off-by:
Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by:
-
Jiasheng Jiang authored
As the possible failure of the kzalloc(), the 'new_ts' could be NULL pointer. Therefore, it should be better to check it in order to avoid the dereference of the NULL pointer. Also, the caller esparser_queue() needs to deal with the return value of the amvdec_add_ts(). Fixes: 876f123b ("media: meson: vdec: bring up to compliance") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Suggested-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
-
Mirela Rabulea authored
If the application queues an NV12M jpeg as output buffer, but then queues a single planar capture buffer, the kernel will crash with "Unable to handle kernel NULL pointer dereference" in mxc_jpeg_addrs, prevent this by finishing the job with error. Signed-off-by:
Mirela Rabulea <mirela.rabulea@oss.nxp.com> Signed-off-by:
-
Jean-Michel Hautbois authored
This packed grey-scale image format has a depth of 10 bits per pixel. Every four consecutive pixels are packed into 5 bytes. Each of the first 4 bytes contain the 8 high order bits of the pixels, and the 5th byte contains the 2 least significants bits of each pixel, in the same order. The first two bytes are not corresponding to this description, fix it. Fixes: af4f4505 ("media: doc: pixfmt-yuv: Move all luma-only YUV formats to common file") Signed-off-by:
Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com> Reviewed-by:
-
Daniel Lundberg Pedersen authored
Example should be comparing errno to EINTR instead of doing assignment. Signed-off-by:
Daniel Lundberg Pedersen <dlp@qtec.com> Reviewed-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Miaoqian Lin authored
The reference taken by 'of_find_device_by_node()' must be released when not needed anymore. Add the corresponding 'put_device()' in the error handling path. Fixes: e7f3c548 ("[media] coda: use VDOA for un-tiling custom macroblock format") Signed-off-by:
Miaoqian Lin <linmq006@gmail.com> Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Signed-off-by:
-
Lad Prabhakar authored
mtk_vpu_probe() calls platform_get_resource(pdev, IORESOURCE_IRQ, ..) to check if IRQ resource exists and later calls platform_get_irq(pdev, ..) to get the actual IRQ. This patch drops an unnecessary call to platform_get_resource() and checks the return value of platform_get_irq(pdev, ..) to make sure the IRQ line is valid. Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
Łukasz Stelmach <l.stelmach@samsung.com> Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq_byname(). Signed-off-by:
-
Lad Prabhakar authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
-
Jacopo Mondi authored
The 'maxim,gpio-poc' property is used when the remote camera power-over-coax is controlled by one of the MAX9286 gpio lines, to instruct the driver about which line to use and what the line polarity is. Add to the max9286 driver support for parsing the newly introduced property and use it if available in place of the usual supply, as it is not possible to establish one as consumer of the max9286 gpio controller. If the new property is present, no gpio controller is registered and 'poc-supply' is ignored. In order to maximize code re-use, break out the max9286 gpio handling function so that they can be used by the gpio controller through the gpio-consumer API, or directly by the driver code. Wrap the power up and power down routines to their own function to be able to use either the gpio line directly or the supply. This will make it easier to control the remote camera power at run time. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by:
-
Jacopo Mondi authored
Define a new vendor property in the maxim,max9286 binding schema. The new property allows to declare that the remote camera power-over-coax is controlled by one of the MAX9286 gpio lines. As it is currently not possible to establish a regulator as consumer of the MAX9286 gpio controller for this purpose, the property allows to declare that the camera power is controlled by the MAX9286 directly. The property accepts a gpio-index (0 or 1) and one line polarity flag as defined by dt-bindings/gpio/gpio.h. Reviewed-by:
-
Jacopo Mondi authored
The dt-bindings examples are usually indented with 4 spaces. The maxim,max9286 schema has the example indented with only 2 spaces, re-indent it. Cosmetic change only. Reviewed-by:
-
- 24 Jan, 2022 5 commits
-
-
Sean Young authored
Re-write without unnecessary shifts. Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
This IR receiver has two limitations: 1) Any IR pulse or space longer than 12ms will be truncated to 12ms 2) Any pulses/spaces after the first 68 are lost ir_raw_event_reset() won't help here. If the IR cannot be decoded, any decoder should reset itself, and if it does not, this is a bug in the decoder. Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by:
-
Sean Young authored
The ir receiver generates an interrupt with the IR data, once a space of at least ok_count is has been seen. Currently this is about 110ms; when holding down a button on a nec remote, no such space is seen until the button is released. This means nothing happens until you release the button. The sample rate is fixed at 46us, so the maximum space that can be encoded is about 12ms. So, the set ok_count above that at 23ms. Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by:
-
Sean Young authored
When a driver reports a timeout, no more IR activity will be reported until the next pulse. A space is inserted between the timeout and the next pulse, based on ktime. The timeout reports already a duration, so this duration should not be added to the gap. Otherwise there is no change to the functionality. Signed-off-by:
-
Peiwei Hu authored
Fix leak in error path. Signed-off-by:
Peiwei Hu <jlu.hpw@foxmail.com> Signed-off-by:
-
- 23 Jan, 2022 10 commits
-
-
Yunfei Dong authored
There are only two lines in mtk_vcodec_release_enc_pm, using pm_runtime_disable and put_device instead directly. Move pm_runtime_enable outside mtk_vcodec_release_enc_pm to symmetry with pm_runtime_disable, after that, rename mtk_vcodec_init_enc_pm to *_clk since it only has clock operations now. Signed-off-by:
Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by:
Yong Wu <yong.wu@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
-
Yunfei Dong authored
There are only two lines in mtk_vcodec_release_dec_pm, using pm_runtime_disable and put_device instead directly. Move pm_runtime_enable outside mtk_vcodec_init_dec_pm to symmetry with pm_runtime_disable, after that, rename mtk_vcodec_init_dec_pm to *_clk since it only has clock operations now. Signed-off-by:
-
Yunfei Dong authored
There is just one core thread, in order to separate different hardware, using codec type to separeate it in scp driver. Signed-off-by:
-
Yunfei Dong authored
Add core dec and dec end ipi msg: AP_IPIMSG_DEC_CORE/AP_IPIMSG_DEC_CORE_END. Signed-off-by:
-
Yunfei Dong authored
Use the dma_set_mask_and_coherent helper to set vdec DMA bit mask to support 34bits iova space(16GB) that the mt8192 iommu HW support. Whole the iova range separate to 0~4G/4G~8G/8G~12G/12G~16G, regarding which iova range VDEC actually locate, it depends on the dma-ranges property of vdec dtsi node. Signed-off-by:
-
Yunfei Dong authored
Add work queue to process core hardware information. First, get lat_buf from message queue, then call core hardware of each codec(H264/VP9/AV1) to decode, finally puts lat_buf back to the message. Signed-off-by:
Steve Cho <stevecho@chromium.org> Signed-off-by:
-
Yunfei Dong authored
For add new hardware, not only need to lock lat hardware, also need to lock core hardware in case of different instance start to decoder at the same time. Signed-off-by:
-
Yunfei Dong authored
Generalizes power and clock on/off interfaces to support different hardware. Signed-off-by:
-
Yunfei Dong authored
For lat and core architecture, lat thread will send message to core thread when lat decode done. Core hardware will use the message from lat to decode, then free message to lat thread when decode done. Signed-off-by:
-
Yunfei Dong authored
Adds irq interface for multi hardware. Signed-off-by:
-
