Signed-off-by: Eduard Gilmutdinov <edgilmutdinov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

On some AIO (All In One) models with the codec alc668
(Vendor ID: 0x10ec0668) on it, when we plug a headphone into the jack,
the system will switch the output to headphone and set the speaker to
automute as well as change the speaker Pin-ctls from 0x40 to 0x00,
this will bring loud noise to the headphone.

I tried to disable the corresponding EAPD, but it did not help to
eliminate the noise.

According to Takashi's suggestion, we use amp operation to replace the
pinctl modification for the automute, this really eliminate the noise.

BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Apply the codec->power_filter to the FG nodes in general for reducing
hackish set_power_state ops override in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A).  This patch removes the indep_hp flag for such codecs.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA.  Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled.  With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The failures of buffer preallocations at driver initializations aren't
critical but it's still helpful to inform, so that user can know that
something doesn't work as expected.

For example, the recent page allocator change triggered regressions,
but developers didn't notice until recently because the driver didn't
complain.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Occasionally, on playback stream ringbuffer wraparound, the EMU20K1
hardware will momentarily return 0 instead of the proper current(loop)
address. This patch handles that case, fixing the problem of playback
position corruption and subsequent loss of buffered sound data, that
occurs with some common buffering layout patterns(e.g. multiple
simultaneous output streams with differently-sized or
non-power-of-2-sized buffers).

An alternate means of fixing the problem would be to read the ca
register continuously, until two sequential reads return the same
value; however, that would be a more invasive change, has performance
implications, and isn't necessary unless there are also issues with the
value not being updated atomically in regards to individual bits or
something similar(which I have not encountered through light testing).

I have no EMU20K2 hardware to confirm if the issue is present there,
but even if it's not, this change shouldn't break anything that's not
already broken.
Signed-off-by: Sarah Bessmer <aotos@fastmail.fm>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of keeping a separate snd-page-alloc module, merge into the
core snd-pcm module, as we don't need to keep it as an individual
module due to the drop of page reservation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

After cutting off the proc and page reservation codes, we don't need
many headers any longer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Nowadays we have CMA for obtaining the contiguous memory pages
efficiently.  Let's kill the old kludge for reserving the memory pages
for large buffers.  It was rarely useful (only for preserving pages
among module reloading or a little help by an early boot scripting),
used only by a couple of drivers, and yet it gives too much ugliness
than its benefit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It's almost superfluous, and doesn't help much for real uses.
Let's reduce the layer size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch adds the device ID for Intel Broadwell display HD-Audio controller,
and applies Haswell properties to this device.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Both patch_realtek.c and patch_conexant.c contain the fairy same code
snippet for supporting Thinkpad ACPI LED controls.  Split them into
thinkpad_helper.c and include it from both places.  Although this
isn't the best approach from the code size POV, the probability for
coexistence of both Realtek and Conexant codecs on a single machine is
pretty low, thus it'll end up with less memory footprint than
splitting to yet another module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.

This patch adds the check of the duplication for avoiding it.

After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints.  This makes even me referring back to the
document often.  Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead.  No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It turned out that some AMD HDMI controllers still don't provide
proper values in GCAP register (all zero), and the driver assigns only
one stream in that case, although the connected codec chip supports
more than one stream.

In this patch, the default max number of streams for AMD HDMI
controllers is increased to 8, which  should suffice for most use
cases.  The overhead by this increase is more azx_dev struct and BDL
allocations, so it's negligible.  Of course, if the controller
provides a proper GCAP register, the register value would be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

this gives ability to convey the valid values of supported rates in
sample_rates array
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that we don't use SNDRV_PCM_RATE_xxx bit fields for sample rate, we need to
change the description to an array for describing the sample rates supported by
the sink/source
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

commit f0e9c080 - "ALSA: compress: change the way sample rates are sent to
kernel" changed the way sample rates are sent. So now we don't need to check for
PCM_RATE_xxx in kernel
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression pdev;
@@

pci_set_power_state(pdev,
- 3
+ PCI_D3hot
 )
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This motherboard seems to have a flaky jack detection - when the
front HP is not present, the jack state quickly switches on and off.

This has been reported by three people in the bug, so I doubt it's
a user error this time.

BugLink: https://bugs.launchpad.net/bugs/1248116Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: Updates  for v3.14

Not a lot going on framework wise, partly due to Christmas at least in
the case of the work I've been doing, but there's been quite a lot of
cleanup activity going on and the usual trickle of new drivers:

 - Update to the generic DMA code to support deferred probe and managed
   resources.
 - New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
   and Analog Devices AXI I2S and S/PDIF controller IPs.
 - Device tree support for the simple card, max98090 and cs42l52.
 - Conversion of the Samsung drivers to native dmaengine, making them
   multiplatform compatible and hopefully helping keep them more modern
   and up to date.
 - More regmap conversions, including a very welcome one for twl6040
   from Peter Ujfalusi.
 - A big overhaul of the DaVinci drivers also from Peter Ujfalusi.

Merge remote-tracking branches 'asoc/topic/ad1836', 'asoc/topic/ad193x', 'asoc/topic/adav80x', 'asoc/topic/adsp', 'asoc/topic/ak4641', 'asoc/topic/ak4642', 'asoc/topic/arizona', 'asoc/topic/atmel', 'asoc/topic/au1x', 'asoc/topic/axi', 'asoc/topic/bcm2835', 'asoc/topic/blackfin', 'asoc/topic/cs4271', 'asoc/topic/cs42l52', 'asoc/topic/da7210', 'asoc/topic/davinci', 'asoc/topic/ep93xx', 'asoc/topic/fsl', 'asoc/topic/fsl-mxs', 'asoc/topic/generic', 'asoc/topic/hdmi', 'asoc/topic/jack', 'asoc/topic/jz4740', 'asoc/topic/max98090', 'asoc/topic/mxs', 'asoc/topic/omap', 'asoc/topic/pxa', 'asoc/topic/rcar', 'asoc/topic/s6000', 'asoc/topic/sai', 'asoc/topic/samsung', 'asoc/topic/sgtl5000', 'asoc/topic/spear', 'asoc/topic/ssm2518', 'asoc/topic/ssm2602', 'asoc/topic/tegra', 'asoc/topic/tlv320aic3x', 'asoc/topic/twl6040', 'asoc/topic/txx9', 'asoc/topic/uda1380', 'asoc/topic/width', 'asoc/topic/wm8510', 'asoc/topic/wm8523', 'asoc/topic/wm8580', 'asoc/topic/wm8711', 'asoc/topic/wm8728', 'asoc/topic/wm8731', 'asoc/topic/wm8741', 'asoc/topic/wm8750', 'asoc/topic/wm8753', 'asoc/topic/wm8776', 'asoc/topic/wm8804', 'asoc/topic/wm8900', 'asoc/topic/wm8901', 'asoc/topic/wm8940', 'asoc/topic/wm8962', 'asoc/topic/wm8974', 'asoc/topic/wm8985', 'asoc/topic/wm8988', 'asoc/topic/wm8990', 'asoc/topic/wm8991', 'asoc/topic/wm8994', 'asoc/topic/wm8995', 'asoc/topic/wm9081' and 'asoc/topic/x86' into asoc-next

Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>

ffs() returns the bit position from 1, while the ssm2158 driver code
assumes it being 0-based.  Also, the bit mask computation of the two
channel slots are incorrect; it must have worked just casually.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>

Try to get the device's module clock if the dt has no clocks and
system-clock-frequency properties.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This is a quick fix for the below two issues when building spdif as modules.

1) If modprobing modules in order: (Step 1) snd-soc-fsl-spdif -> (Step 2)
snd-soc-imx-spdif -> (Step 3) snd-soc-spdif-tx/rx, we will fail to create
imx-spdif card and dai link unless we rmmod snd-soc-imx-spdif and modprobe
it again due to the execution platform_driver_unregister() in probe() when
meeting -EPROBE_DEFER at Step 2.

2) After "imx-spdif sound-spdif.17: dit-hifi <-> 2004000.spdif mapping ok",
'rmmod snd-soc-imx-spdif' would cause kernel dump with warning:
WARNING: CPU: 0 PID: 1301 at /home/rmk/git/linux-rmk/fs/sysfs/dir.c:915 sysfs_hash_and_remove+0x84/0x90()
sysfs: can not remove 'dapm_widget', no directory
This should be caused by disordered resourse releasing of the whole link.
And trying to unregister the card and then CODEC dev can't fix this issue.

Thus this patch just provides a simple fix to these two bugs by using the
snd-soc-dummy in the core instead of seperate snd-soc-spdif-tx/rx so that
there's no need to handle the registering and unregistering of CODEC or
CODEC dai any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>