This patch (as949) changes the usbmon driver to use the new urb->ep
field rather than urb->pipe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as948) removes most of the references to urb->pipe from
the usbfs routines in devio.c.  The one tricky aspect is in
snoop_urb(), which can be called before the URB is submitted and which
uses usb_urb_dir_in().  For this to work properly, the URB's direction
flag must be set manually in proc_do_submiturb().

The patch also fixes a minor bug; the wValue, wIndex, and wLength
fields were snooped in proc_do_submiturb() without conversion from
le16 to CPU-byte-ordering.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as947) changes the device initialization and enumeration
code in hub.c; now udev->devnum will be set to 0 while the device is
being accessed at address 0.  Until now this wasn't needed because the
address value was passed as part of urb->pipe; without that field the
device address must be stored elsewhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as946) eliminates many of the uses of urb->pipe in
usbcore.  Unfortunately there will have to be a significant API
change, affecting all USB drivers, before we can remove it entirely.
This patch contents itself with changing only the interface to
usb_buffer_map_sg() and friends: The pipe argument is replaced with a
direction flag.  That can be done easily because those routines get
used in only one place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as945) adds a bit to urb->transfer_flags for recording the
direction of the URB.  The bit is set/cleared automatically in
usb_submit_urb() so drivers don't have to worry about it (although as
a result, it isn't valid until the URB has been submitted).  Inline
routines are added for easily checking an URB's direction.  They
replace calls to usb_pipein in the DMA-mapping parts of hcd.c.

For non-control endpoints, the direction is determined directly from
the endpoint descriptor.  However control endpoints are
bi-directional; for them the direction is determined from the
bRequestType byte and the wLength value in the setup packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as944) adds an explicit "enabled" field to the
usb_host_endpoint structure and uses it in place of the current
mechanism.  This is merely a time-space tradeoff; it makes checking
whether URBs may be submitted to an endpoint simpler.  The existing
mechanism is efficient when converting urb->pipe to an endpoint
pointer, but it's not so efficient when urb->ep is used instead.

As a side effect, the procedure for enabling an endpoint is now a
little more complicated.  The ad-hoc inline code in usb.c and hub.c
for enabling ep0 is now replaced with calls to usb_enable_endpoint,
which is no longer static.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as943) prepares the way for eliminating urb->pipe by
introducing an endpoint pointer into struct urb.  For now urb->ep
is set by usb_submit_urb() from the pipe value; eventually drivers
will set it themselves and we will remove urb->pipe completely.

The patch also adds new inline routines to retrieve an endpoint
descriptor's number and transfer type, essentially as replacements for
usb_pipeendpoint and usb_pipetype.

usb_submit_urb(), usb_hcd_submit_urb(), and usb_hcd_unlink_urb() are
converted to use the new field and new routines.  Other parts of
usbcore will be converted in later patches.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Coverity checker spotted that we have already oops'ed if "us"
was NULL.

Since "us" can't be NULL in the only caller this patch removes the
NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This just fixes some whitespace bugs in <linux/usb_gadget.h>,
mostly extraneous spaces where a single tab suffices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Remove the references to CONFIG_USBD_SAFE_SERIAL_{VENDOR,PRODUCT},
which aren't defined in any Kconfig file.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The ZF Micro OHCI controller exhibits unexpected behavior that seems to be
related to high load.  Under certain conditions, the controller will
complete a TD, remove it from the endpoint's queue, and fail to add it to
the donelist. This causes the endpoint to appear to stop responding. Worse,
if the device is removed while in that state, OHCI will hang while waiting
for the orphaned TD to complete.  The situation is not recoverable without
rebooting.

This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag:

 1. A watchdog routine periodically scans the OHCI structures to check
    for orphaned TDs. In these cases the TD is taken back from the
    controller and completed normally.

 2. If a device is removed while the endpoint is hung but before the
    watchdog catches the situation, any outstanding TDs are taken back
    from the controller in the 'sanitize' phase.

The ohci-hcd driver used to print "INTR_SF lossage" in this situation;
this changes it to the universally accurate "ED unlink timeout".  Other
instances of this message presumably have different root causes.

Both this Compaq quirk and a NEC quirk are now properly compiled out for
non-PCI builds of this driver.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Employ the new API URB_FREE_BUFFER that we've got. There was talk of a combined
constructor for this case, but apparently it's not happening, so just set the
flag explicitly for now.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch implements a mode when a printer returns ENOSPC when it runs
out of paper. The default remains the same as before. An application which
wishes to use this function has to enable it explicitly with an ioctl
LPABORT.

This is done on a request by our (Fedora) CUPS guy, Tim Waugh. The API is
similar enough to the lp0's one that CUPS works with both (but see below),
but it's has some differences.

Most importantly, the abort mode is persistent in case of lp0: once tunelp
was run your cat fill blow up until you reboot or run tunelp again. For
usblp, I made it so the abort mode is only in effect as long as device
is open. This way you can mix and match CUPS and cat(1) freely and nothing
bad happens even if you run out of paper. It is also safer in the face
of any unexpected crashes.

It has to be noted that mixing LPABORT and O_NONBLOCK is not advised.
It probably does not do what you want: instead of returning -ENOSPC
it will always return -EAGAIN (because it would otherwise block while
waiting for the paper). Applications which use O_NONBLOCK should continue
to use LPGETSTATUS like before.

Finally, CUPS actually requires patching to take full advantage of this.
It has several components; those which invoke LPABORT work, but some of
them need the ioctl added. This is completely compatible, you can mix
old CUPS and new kernels or vice versa.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch cleans up duplicate includes in
	drivers/usb/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This trivial patch removes the unneeded pointer intf returned from
usb_ifnum_to_if(), which is never used. The check for NULL can be simply done
by if (!usb_ifnum_to_if(usb_dev, 2)).
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ZLIB]: Fix external builds of zlib_inflate code.
  [TG3]: Fix APE induced regression
  [SKY2]: version 1.19
  [SKY2]: use netdevice stats struct
  [SKY2]: fiber advertise bits initialization (trivial)
  [SKY2]: fix power settings on Yukon XL
  [SKY2]: ethtool register reserved area blackout

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move zlib_inflate_blob() out into it's own source file,
infutil.c, so that things like the powerpc zImage builder
in arch/powerpc/boot/Makefile don't end up trying to
compile it.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.

Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
  [POWERPC] Add memchr() to the bootwrapper
  [POWERPC] Implement logging of unhandled signals
  [POWERPC] Add legacy serial support for OPB with flattened device tree
  [POWERPC] Use 1TB segments
  [POWERPC] XilinxFB: Allow fixed framebuffer base address
  [POWERPC] XilinxFB: Add support for custom screen resolution
  [POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
  [POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
  [POWERPC] 4xx: Kilauea defconfig file
  [POWERPC] 4xx: Kilauea DTS
  [POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
  [POWERPC] 4xx: Add AMCC 405EX support to cputable.c
  [POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
  [POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
  [POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
  [POWERPC] 85xx: Killed <asm/mpc85xx.h>
  [POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
  [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
  [POWERPC] mpc8272ads: Remove muram from the CPM reg property.
  [POWERPC] Make clockevents work on PPC601 processors
  ...

Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] sata_mv: more S/G fixes

* corruption fix: we only want the lower 16 bits of length (0 == 64kb)

* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
  so we must reset it to own hw-specific length.

* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Implement show_unhandled_signals sysctl + support to print when a process
is killed due to unhandled signals just as i386 and x86_64 does.

Default to having it off, unlike x86 that defaults on.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Currently find_legacy_serial_ports() can find no serial ports on the
OPB with flattened device tree.  Thus no legacy boot console can be
initialized.  Just the early udbg console works, which is initialized
with udbg_init_44x_as1 on the UART's physical address specified in
kernel config.  This happens because we look for ns16750 serial
devices only and expect opb node to have a device type property.  This
patch makes it look for ns16550-compatible devices and use
of_device_is_compatible() for opb in case device type is not
specified.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).

We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.

We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments.  That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.

Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>

Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Some custom implementations of the xilinx fb can use resolutions other
than 640x480.  This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver.  Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add 64-bit physical address support to setup_indirect_pci().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
  mlx4_core: Fix section mismatches
  IPoIB: Allow setting policy to ignore multicast groups
  IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
  IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
  IB/ipath: Remove redundant link state checks
  IB/ipath: Fix IB_EVENT_PORT_ERR event
  IB/ipath: Better handling of unexpected GPIO interrupts
  IB/ipath: Maintain active time on all chips
  IB/ipath: Fix QHT7040 serial number check
  IB/ipath: Indicate a couple of chip bugs to userspace
  IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
  IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
  IB/ipath: Remove duplicate copy of LMC
  IB/ipath: Add ability to set the LMC via the sysfs debugging interface
  IB/ipath: Optimize completion queue entry insertion and polling
  IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
  IB/ipath: Generate flush CQE when QP is in error state
  IB/ipath: Remove redundant code
  IB/ipath: Future proof eeprom checksum code (contents reading)
  IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
  [SKY2]: status polling loop (post merge)
  [NET]: Fix NAPI completion handling in some drivers.
  [TCP]: Limit processing lost_retrans loop to work-to-do cases
  [TCP]: Fix lost_retrans loop vs fastpath problems
  [TCP]: No need to re-count fackets_out/sacked_out at RTO
  [TCP]: Extract tcp_match_queue_to_sack from sacktag code
  [TCP]: Kill almost unused variable pcount from sacktag
  [TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
  [TCP]: Add bytes_acked (ABC) clearing to FRTO too
  [IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
  [NETFILTER]: x_tables: add missing ip6t_modulename aliases
  [NETFILTER]: nf_conntrack_tcp: fix connection reopening
  [QETH]: fix qeth_main.c
  [NETLINK]: fib_frontend build fixes
  [IPv6]: Export userland ND options through netlink (RDNSS support)
  [9P]: build fix with !CONFIG_SYSCTL
  [NET]: Fix dev_put() and dev_hold() comments
  [NET]: make netlink user -> kernel interface synchronious
  [NET]: unify netlink kernel socket recognition
  [NET]: cleanup 3rd argument in netlink_sendskb
  ...

Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.

(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (80 commits)
  [MIPS] tlbex.c: Cleanup __init usage.
  [MIPS] WRPPMC serial support move to platform device
  [MIPS] R1: Fix hazard barriers to make kernels work on R2 also.
  [MIPS] VPE: reimplement ELF loader.
  [MIPS] cleanup WRPPMC include files
  [MIPS] Add BUG_ON assertion for attempt to run kernel on the wrong CPU type.
  [MIPS] SMP: Use ISO C struct initializer for local structs.
  [MIPS] SMP: Kill useless casts.
  [MIPS] Kill num_online_cpus() loops.
  [MIPS] SMP: Implement smp_call_function_mask().
  [MIPS] Make facility to convert CPU types to strings generally available.
  [MIPS] Convert list of CPU types from #define to enum.
  [MIPS] Optimize get_unaligned / put_unaligned implementations.
  [MIPS] checkfiles: Fix "need space after that ','" errors.
  [MIPS] Fix "no space between function name and open parenthesis" warnings.
  [MIPS] Allow hardwiring of the CPU type to a single type for optimization.
  [MIPS] tlbex: Size optimize code by declaring a few functions inline.
  [MIPS] pg-r4k.c: Dump the generated code
  [MIPS] Cobalt: Remove cobalt_machine_power_off()
  [MIPS] Cobalt: Move reset port definition to arch/mips/cobalt/reset.c
  ...