- 22 Sep, 2021 5 commits
-
-
Shai Malin authored
If the HW device is during recovery, the HW resources will never return, hence we shouldn't wait for the CID (HW context ID) bitmaps to clear. This fix speeds up the error recovery flow. Fixes: 64515dc8 ("qed: Add infrastructure for error detection and recovery") Signed-off-by:
Michal Kalderon <mkalderon@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
Shai Malin <smalin@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Julian Wiedmann says: ==================== s390/qeth: fixes 2021-09-21 This brings two fixes for deadlocks when a device is removed while it has certain types of async work pending. And one additional fix for a missing NULL check in an error case. ==================== Link: https://lore.kernel.org/r/20210921145217.1584654-1-jwi@linux.ibm.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Alexandra Winter authored
Commit 0b9902c1 ("s390/qeth: fix deadlock during recovery") removed taking discipline_mutex inside qeth_do_reset(), fixing potential deadlocks. An error path was missed though, that still takes discipline_mutex and thus has the original deadlock potential. Intermittent deadlocks were seen when a qeth channel path is configured offline, causing a race between qeth_do_reset and ccwgroup_remove. Call qeth_set_offline() directly in the qeth_do_reset() error case and then a new variant of ccwgroup_set_offline(), without taking discipline_mutex. Fixes: b41b554c ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Reviewed-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Alexandra Winter authored
Problem: qeth_close_dev_handler is a worker that tries to acquire card->discipline_mutex via drv->set_offline() in ccwgroup_set_offline(). Since commit b41b554c ("s390/qeth: fix locking for discipline setup / removal") qeth_remove_discipline() is called under card->discipline_mutex and cancels the work and waits for it to finish. STOPLAN reception with reason code IPA_RC_VEPA_TO_VEB_TRANSITION is the only situation that schedules close_dev_work. In that situation scheduling qeth recovery will also result in an offline interface, when resetting the isolation mode fails, if the external switch is still set to VEB. And since commit 0b9902c1 ("s390/qeth: fix deadlock during recovery") qeth recovery does not aquire card->discipline_mutex anymore. So we accept the longer pathlength of qeth_schedule_recovery in this error situation and re-use the existing function. As a side-benefit this changes the hwtrap to behave like during recovery instead of like during a user-triggered set_offline. Fixes: b41b554c ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by:
-
Julian Wiedmann authored
When qeth_set_online() calls qeth_clear_working_pool_list() to roll back after an error exit from qeth_hardsetup_card(), we are at risk of accessing card->qdio.in_q before it was allocated by qeth_alloc_qdio_queues() via qeth_mpc_initialize(). qeth_clear_working_pool_list() then dereferences NULL, and by writing to queue->bufs[i].pool_entry scribbles all over the CPU's lowcore. Resulting in a crash when those lowcore areas are used next (eg. on the next machine-check interrupt). Such a scenario would typically happen when the device is first set online and its queues aren't allocated yet. An early IO error or certain misconfigs (eg. mismatched transport mode, bad portno) then cause us to error out from qeth_hardsetup_card() with card->qdio.in_q still being NULL. Fix it by checking the pointer for NULL before accessing it. Note that we also have (rare) paths inside qeth_mpc_initialize() where a configuration change can cause us to free the existing queues, expecting that subsequent code will allocate them again. If we then error out before that re-allocation happens, the same bug occurs. Fixes: eff73e16 ("s390/qeth: tolerate pre-filled RX buffer") Reported-by:
Stefan Raspl <raspl@linux.ibm.com> Root-caused-by:
Heiko Carstens <hca@linux.ibm.com> Signed-off-by:
-
- 21 Sep, 2021 8 commits
-
-
David S. Miller authored
Vladimir Oltean says: ==================== Fix mdiobus users with devres Commit ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") by Bartosz Golaszewski has introduced two classes of potential bugs by making the devres callback of devm_mdiobus_alloc stop calling mdiobus_unregister. The exact buggy circumstances are presented in the individual commit messages. I have searched the tree for other occurrences, but at the moment: - for issue (a) I have no concrete proof that other buses except SPI and I2C suffer from it, and the only SPI or I2C device drivers that call of_mdiobus_alloc are the DSA drivers that leave a NULL ds->slave_mii_bus and a non-NULL ds->ops->phy_read, aka ksz9477, ksz8795, lan9303_i2c, vsc73xx-spi. - for issue (b), all drivers which call of_mdiobus_alloc either use of_mdiobus_register too, or call mdiobus_unregister sometime within the ->remove path. Although at this point I've seen enough strangeness caused by this "device_del during ->shutdown" that I'm just going to copy the SPI and I2C subsystem maintainers to this patch series, to get their feedback whether they've had reports about things like this before. I don't think other buses behave in this way, it forces SPI and I2C devices to have to protect themselves from a really strange set of issues. ==================== Signed-off-by:
-
Vladimir Oltean authored
The Linux device model permits both the ->shutdown and ->remove driver methods to get called during a shutdown procedure. Example: a DSA switch which sits on an SPI bus, and the SPI bus driver calls this on its ->shutdown method: spi_unregister_controller -> device_for_each_child(&ctlr->dev, NULL, __unregister); -> spi_unregister_device(to_spi_device(dev)); -> device_del(&spi->dev); So this is a simple pattern which can theoretically appear on any bus, although the only other buses on which I've been able to find it are I2C: i2c_del_adapter -> device_for_each_child(&adap->dev, NULL, __unregister_client); -> i2c_unregister_device(client); -> device_unregister(&client->dev); The implication of this pattern is that devices on these buses can be unregistered after having been shut down. The drivers for these devices might choose to return early either from ->remove or ->shutdown if the other callback has already run once, and they might choose that the ->shutdown method should only perform a subset of the teardown done by ->remove (to avoid unnecessary delays when rebooting). So in other words, the device driver may choose on ->remove to not do anything (therefore to not unregister an MDIO bus it has registered on ->probe), because this ->remove is actually triggered by the device_shutdown path, and its ->shutdown method has already run and done the minimally required cleanup. This used to be fine until the blamed commit, but now, the following BUG_ON triggers: void mdiobus_free(struct mii_bus *bus) { /* For compatibility with error handling in drivers. */ if (bus->state == MDIOBUS_ALLOCATED) { kfree(bus); return; } BUG_ON(bus->state != MDIOBUS_UNREGISTERED); bus->state = MDIOBUS_RELEASED; put_device(&bus->dev); } In other words, there is an attempt to free an MDIO bus which was not unregistered. The attempt to free it comes from the devres release callbacks of the SPI device, which are executed after the device is unregistered. I'm not saying that the fact that MDIO buses allocated using devres would automatically get unregistered wasn't strange. I'm just saying that the commit didn't care about auditing existing call paths in the kernel, and now, the following code sequences are potentially buggy: (a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device located on a bus that unregisters its children on shutdown. After the blamed patch, either both the alloc and the register should use devres, or none should. (b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no mdiobus_unregister at all in the remove path. After the blamed patch, nobody unregisters the MDIO bus anymore, so this is even more buggy than the previous case which needs a specific bus configuration to be seen, this one is an unconditional bug. In this case, the Realtek drivers fall under category (b). To solve it, we can register the MDIO bus under devres too, which restores the previous behavior. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by:Lino Sanfilippo <LinoSanfilippo@gmx.de> Reported-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Vladimir Oltean authored
The Linux device model permits both the ->shutdown and ->remove driver methods to get called during a shutdown procedure. Example: a DSA switch which sits on an SPI bus, and the SPI bus driver calls this on its ->shutdown method: spi_unregister_controller -> device_for_each_child(&ctlr->dev, NULL, __unregister); -> spi_unregister_device(to_spi_device(dev)); -> device_del(&spi->dev); So this is a simple pattern which can theoretically appear on any bus, although the only other buses on which I've been able to find it are I2C: i2c_del_adapter -> device_for_each_child(&adap->dev, NULL, __unregister_client); -> i2c_unregister_device(client); -> device_unregister(&client->dev); The implication of this pattern is that devices on these buses can be unregistered after having been shut down. The drivers for these devices might choose to return early either from ->remove or ->shutdown if the other callback has already run once, and they might choose that the ->shutdown method should only perform a subset of the teardown done by ->remove (to avoid unnecessary delays when rebooting). So in other words, the device driver may choose on ->remove to not do anything (therefore to not unregister an MDIO bus it has registered on ->probe), because this ->remove is actually triggered by the device_shutdown path, and its ->shutdown method has already run and done the minimally required cleanup. This used to be fine until the blamed commit, but now, the following BUG_ON triggers: void mdiobus_free(struct mii_bus *bus) { /* For compatibility with error handling in drivers. */ if (bus->state == MDIOBUS_ALLOCATED) { kfree(bus); return; } BUG_ON(bus->state != MDIOBUS_UNREGISTERED); bus->state = MDIOBUS_RELEASED; put_device(&bus->dev); } In other words, there is an attempt to free an MDIO bus which was not unregistered. The attempt to free it comes from the devres release callbacks of the SPI device, which are executed after the device is unregistered. I'm not saying that the fact that MDIO buses allocated using devres would automatically get unregistered wasn't strange. I'm just saying that the commit didn't care about auditing existing call paths in the kernel, and now, the following code sequences are potentially buggy: (a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device located on a bus that unregisters its children on shutdown. After the blamed patch, either both the alloc and the register should use devres, or none should. (b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no mdiobus_unregister at all in the remove path. After the blamed patch, nobody unregisters the MDIO bus anymore, so this is even more buggy than the previous case which needs a specific bus configuration to be seen, this one is an unconditional bug. In this case, DSA falls into category (a), it tries to be helpful and registers an MDIO bus on behalf of the switch, which might be on such a bus. I've no idea why it does it under devres. It does this on probe: if (!ds->slave_mii_bus && ds->ops->phy_read) alloc and register mdio bus and this on remove: if (ds->slave_mii_bus && ds->ops->phy_read) unregister mdio bus I _could_ imagine using devres because the condition used on remove is different than the condition used on probe. So strictly speaking, DSA cannot determine whether the ds->slave_mii_bus it sees on remove is the ds->slave_mii_bus that _it_ has allocated on probe. Using devres would have solved that problem. But nonetheless, the existing code already proceeds to unregister the MDIO bus, even though it might be unregistering an MDIO bus it has never registered. So I can only guess that no driver that implements ds->ops->phy_read also allocates and registers ds->slave_mii_bus itself. So in that case, if unregistering is fine, freeing must be fine too. Stop using devres and free the MDIO bus manually. This will make devres stop attempting to free a still registered MDIO bus on ->shutdown. Fixes: ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by:Florian Fainelli <f.fainelli@gmail.com> Tested-by:
-
Masanari Iida authored
This patch fixes a spelling typo in ice.rst Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Since the blamed commit, dsa_tree_teardown_switches() was split into two smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports. However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports. Fixes: a57d8c21 ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports") Signed-off-by:
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: fixes 2021-09-20 Please apply the following patches for smc to netdev's net tree. The first patch adds a missing error check, and the second patch fixes a possible leak of a lock in a worker. ==================== Signed-off-by: -
Karsten Graul authored
The abort_work is scheduled when a connection was detected to be out-of-sync after a link failure. The work calls smc_conn_kill(), which calls smc_close_active_abort() and that might end up calling smc_close_cancel_work(). smc_close_cancel_work() cancels any pending close_work and tx_work but needs to release the sock_lock before and acquires the sock_lock again afterwards. So when the sock_lock was NOT acquired before then it may be held after the abort_work completes. Thats why the sock_lock is acquired before the call to smc_conn_kill() in __smc_lgr_terminate(), but this is missing in smc_conn_abort_work(). Fix that by acquiring the sock_lock first and release it after the call to smc_conn_kill(). Fixes: b286a065 ("net/smc: handle incoming CDC validation message") Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Karsten Graul authored
Coverity stumbled over a missing error check in smc_clc_prfx_set(): *** CID 1475954: Error handling issues (CHECKED_RETURN) /net/smc/smc_clc.c: 233 in smc_clc_prfx_set() >>> CID 1475954: Error handling issues (CHECKED_RETURN) >>> Calling "kernel_getsockname" without checking return value (as is done elsewhere 8 out of 10 times). 233 kernel_getsockname(clcsock, (struct sockaddr *)&addrs); Add the return code check in smc_clc_prfx_set(). Fixes: c246d942 ("net/smc: restructure netinfo for CLC proposal msgs") Reported-by:
-
- 20 Sep, 2021 11 commits
-
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: add some fixes for -net This series adds some fixes for the HNS3 ethernet driver. ==================== Signed-off-by: -
Yufeng Mo authored
hclge_get_reset_status() should return the tqp reset status. However, if the CMDQ fails, the caller will take it as tqp reset success status by mistake. Therefore, uses a parameters to get the tqp reset status instead. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
liaoguojia authored
The input parameters may not be reliable, so check the vlan id before using it, otherwise may set wrong vlan id into hardware. Fixes: dc8131d8 ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls") Signed-off-by:
liaoguojia <liaoguojia@huawei.com> Signed-off-by:
-
Yufeng Mo authored
The input parameters may not be reliable. Before using the queue id, we should check this parameter. Otherwise, memory overwriting may occur. Fixes: d3410018 ("net: hns3: refactor the mailbox message between PF and VF") Signed-off-by:
-
Jiaran Zhang authored
vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs. So the actual vf id is equal to vport_id minus 1. Some VF print logs are actually vport, and logs of vf id actually use vport id, so this patch fixes them. Fixes: ac887be5 ("net: hns3: change print level of RAS error log from warning to error") Fixes: adcf738b ("net: hns3: cleanup some print format warning") Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
Jian Shen authored
The vf id from ethtool is added 1 before configured to driver. So it's necessary to minus 1 when printing it, in order to keep consistent with user's configuration. Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
When user change rss 'hfunc' without set rss 'hkey' by ethtool -X command, the driver will ignore the 'hfunc' for the hkey is NULL. It's unreasonable. So fix it. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: 374ad291 ("net: hns3: Add RSS general configuration support for VF") Signed-off-by:
-
Arnd Bergmann authored
Without CONFIG_COMMON_CLK, this fails to link: arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_register_i2c': ptp_ocp.c:(.text+0xcc0): undefined reference to `__clk_hw_register_fixed_rate' arm-linux-gnueabi-ld: ptp_ocp.c:(.text+0xcf4): undefined reference to `devm_clk_hw_register_clkdev' arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_detach': ptp_ocp.c:(.text+0x1c24): undefined reference to `clk_hw_unregister_fixed_rate' Fixes: a7e1abad ("ptp: Add clock driver for the OpenCompute TimeCard.") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Michael Chan authored
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS + 1. Because the first TX BD for a packet is always a long TX BD, we need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with this value to make this more clear. The current code uses a minimum that is off by 1. Fix it using this constant. The tx_wake_thresh to determine when to wake up the TX queue is half the ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next packet which may have maximum fragments. So the comparison of the available TX BDs with tx_wake_thresh should be >= instead of > in the current code. Otherwise, at the smallest ring size, we will never wake up the TX queue and will cause TX timeout. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadocm.com> Signed-off-by:
-
Ido Schimmel authored
The resilient nexthop group torture tests in fib_nexthop.sh exposed a possible division by zero while replacing a resilient group [1]. The division by zero occurs when the data path sees a resilient nexthop group with zero buckets. The tests replace a resilient nexthop group in a loop while traffic is forwarded through it. The tests do not specify the number of buckets while performing the replacement, resulting in the kernel allocating a stub resilient table (i.e, 'struct nh_res_table') with zero buckets. This table should never be visible to the data path, but the old nexthop group (i.e., 'oldg') might still be used by the data path when the stub table is assigned to it. Fix this by only assigning the stub table to the old nexthop group after making sure the group is no longer used by the data path. Tested with fib_nexthops.sh: Tests passed: 222 Tests failed: 0 [1] divide error: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 1850 Comm: ping Not tainted 5.14.0-custom-10271-ga86eb53057fe #1107 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:nexthop_select_path+0x2d2/0x1a80 [...] Call Trace: fib_select_multipath+0x79b/0x1530 fib_select_path+0x8fb/0x1c10 ip_route_output_key_hash_rcu+0x1198/0x2da0 ip_route_output_key_hash+0x190/0x340 ip_route_output_flow+0x21/0x120 raw_sendmsg+0x91d/0x2e10 inet_sendmsg+0x9e/0xe0 __sys_sendto+0x23d/0x360 __x64_sys_sendto+0xe1/0x1b0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Cc: stable@vger.kernel.org Fixes: 283a72a5 ("nexthop: Add implementation of resilient next-hop groups") Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Xuan Zhuo authored
The process will cause napi.state to contain NAPI_STATE_SCHED and not in the poll_list, which will cause napi_disable() to get stuck. The prefix "NAPI_STATE_" is removed in the figure below, and NAPI_STATE_HASHED is ignored in napi.state. CPU0 | CPU1 | napi.state =============================================================================== napi_disable() | | SCHED | NPSVC napi_enable() | | { | | smp_mb__before_atomic(); | | clear_bit(SCHED, &n->state); | | NPSVC | napi_schedule_prep() | SCHED | NPSVC | napi_poll() | | napi_complete_done() | | { | | if (n->state & (NPSVC | | (1) | _BUSY_POLL))) | | return false; | | ................ | | } | SCHED | NPSVC | | clear_bit(NPSVC, &n->state); | | SCHED } | | | | napi_schedule_prep() | | SCHED | MISSED (2) (1) Here return direct. Because of NAPI_STATE_NPSVC exists. (2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list Since NAPI_STATE_SCHED already exists and napi is not in the sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always exist. 1. This will cause this queue to no longer receive packets. 2. If you encounter napi_disable under the protection of rtnl_lock, it will cause the entire rtnl_lock to be locked, affecting the overall system. This patch uses cmpxchg to implement napi_enable(), which ensures that there will be no race due to the separation of clear two bits. Fixes: 2d8bff12 ("netpoll: Close race condition between poll_one_napi and napi_disable") Signed-off-by:Xuan Zhuo <xuanzhuo@linux.alibaba.com> Reviewed-by:
Dust Li <dust.li@linux.alibaba.com> Signed-off-by:
-
- 19 Sep, 2021 16 commits
-
-
Shuah Khan authored
Makefile uses TEST_PROGS instead of TEST_GEN_PROGS to define executables. TEST_PROGS is for shell scripts that need to be installed and run by the common lib.mk framework. The common framework doesn't touch TEST_PROGS when it does build and clean. As a result "make kselftest-clean" and "make clean" fail to remove executables. Run and install work because the common framework runs and installs TEST_PROGS. Build works because the Makefile defines "all" rule which is unnecessary if TEST_GEN_PROGS is used. Use TEST_GEN_PROGS so the common framework can handle build/run/ install/clean properly. Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Lama Kayal authored
Any link state change that's done prior to net device registration isn't reflected on the state, thus the operational state is left obsolete, with 'UNKNOWN' status. To resolve the issue, query link state from FW upon open operations to ensure operational state is updated. Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by:
Lama Kayal <lkayal@nvidia.com> Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Shuah Khan authored
Fix the args to fprintf(). Splitting the message ends up passing incorrect arg for "sigurg %d" and an extra arg overall. The test result message ends up incorrect. test_unix_oob.c: In function ‘main’: test_unix_oob.c:274:43: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘char *’ [-Wformat=] 274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ", | ~^ | | | int | %s 275 | "atmark %d\n", signal_recvd, len, oob, atmark); | ~~~~~~~~~~~~~ | | | char * test_unix_oob.c:274:19: warning: too many arguments for format [-Wformat-extra-args] 274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ", Signed-off-by: -
Christian Lamparter authored
Due to the inclusion of nvmem handling into the mac-address getter function of_get_mac_address() by commit d01f449c ("of_net: add NVMEM support to of_get_mac_address") it is now possible to get a -EPROBE_DEFER return code. Which did cause bgmac to assign a random ethernet address. This exact issue happened on my Meraki MR32. The nvmem provider is an EEPROM (at24c64) which gets instantiated once the module driver is loaded... This happens once the filesystem becomes available. With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error. Then the driver subsystem will reschedule the probe at a later time. Cc: Petr Štetiar <ynezz@true.cz> Cc: Michael Walle <michael@walle.cc> Fixes: d01f449c ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Commit 86f8b1c0 ("net: dsa: Do not make user port errors fatal") decided it was fine to ignore errors on certain ports that fail to probe, and go on with the ports that do probe fine. Commit fb6ec87f ("net: dsa: Fix type was not set for devlink port") noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get called, and devlink notices after a timeout of 3600 seconds and prints a WARN_ON. So it went ahead to unregister the devlink port. And because there exists an UNUSED port flavour, we actually re-register the devlink port as UNUSED. Commit 08156ba4 ("net: dsa: Add devlink port regions support to DSA") added devlink port regions, which are set up by the driver and not by DSA. When we trigger the devlink port deregistration and reregistration as unused, devlink now prints another WARN_ON, from here: devlink_port_unregister: WARN_ON(!list_empty(&devlink_port->region_list)); So the port still has regions, which makes sense, because they were set up by the driver, and the driver doesn't know we're unregistering the devlink port. Somebody needs to tear them down, and optionally (actually it would be nice, to be consistent) set them up again for the new devlink port. But DSA's layering stays in our way quite badly here. The options I've considered are: 1. Introduce a function in devlink to just change a port's type and flavour. No dice, devlink keeps a lot of state, it really wants the port to not be registered when you set its parameters, so changing anything can only be done by destroying what we currently have and recreating it. 2. Make DSA cache the parameters passed to dsa_devlink_port_region_create, and the region returned, keep those in a list, then when the devlink port unregister needs to take place, the existing devlink regions are destroyed by DSA, and we replay the creation of new regions using the cached parameters. Problem: mv88e6xxx keeps the region pointers in chip->ports[port].region, and these will remain stale after DSA frees them. There are many things DSA can do, but updating mv88e6xxx's private pointers is not one of them. 3. Just let the driver do it (i.e. introduce a very specific method called ds->ops->port_reinit_as_unused, which unregisters its devlink port devlink regions, then the old devlink port, then registers the new one, then the devlink port regions for it). While it does work, as opposed to the others, it's pretty horrible from an API perspective and we can do better. 4. Introduce a new pair of methods, ->port_setup and ->port_teardown, which in the case of mv88e6xxx must register and unregister the devlink port regions. Call these 2 methods when the port must be reinitialized as unused. Naturally, I went for the 4th approach. Fixes: 08156ba4 ("net: dsa: Add devlink port regions support to DSA") Signed-off-by:
-
Krzysztof Kozlowski authored
The MODULE_DEVICE_TABLE already creates proper alias for platform driver. Having another MODULE_ALIAS causes the alias to be duplicated. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
David S. Miller authored
Colin Foster says: ==================== ocelot phylink fixes When the ocelot driver was migrated to phylink, e6e12df6 ("net: mscc: ocelot: convert to phylink") there were two additional writes to registers that became stale. One write was to DEV_CLOCK_CFG and one was to ANA_PFC_PCF_CFG. Both of these writes referenced the variable "speed" which originally was set to OCELOT_SPEED_{10,100,1000,2500}. These macros expand to values of 3, 2, 1, or 0, respectively. After the update, the variable speed is set to SPEED_{10,100,1000,2500} which expand to 10, 100, 1000, and 2500. So invalid values were getting written to the two registers, which would lead to either a lack of functionality or undefined funcationality. Fixing these values was the intent of v1 of this patch set - submitted as "[PATCH v1 net] net: ethernet: mscc: ocelot: bug fix when writing MAC speed" During that review it was determined that both writes were actually unnecessary. DEV_CLOCK_CFG is a duplicate write, so can be removed entirely. This was accidentally submitted as as a new, lone patch titled "[PATCH v1 net] net: mscc: ocelot: remove buggy duplicate write to DEV_CLOCK_CFG". This is part of what is considered v2 of this patch set. Additionally, the write to ANA_PFC_PFC_CFG is also unnecessary. Priority flow contol is disabled, so configuring it is useless and should be removed. This was also submitted as a new, lone patch titled "[PATCH v1 net] net: mscc: ocelot: remove buggy and useless write to ANA_PFC_PFC_CFG". This is the rest of what is considered v2 of this patch set. v3 Identical to v2, but fixes the patch numbering to v3 and submitting the two changes as a patch set. v2 Note: I misunderstood and submitted two new "v1" patches instead of a single "v2" patch set. - Remove the buggy writes altogher ==================== Signed-off-by:
-
Colin Foster authored
When updating ocelot to use phylink, a second write to DEV_CLOCK_CFG was mistakenly left in. It used the variable "speed" which, previously, would would have been assigned a value of OCELOT_SPEED_1000. In phylink the variable is be SPEED_1000, which is invalid for the DEV_CLOCK_LINK_SPEED macro. Removing it as unnecessary and buggy. Fixes: e6e12df6 ("net: mscc: ocelot: convert to phylink") Signed-off-by:
Colin Foster <colin.foster@in-advantage.com> Reviewed-by:
-
Colin Foster authored
A useless write to ANA_PFC_PFC_CFG was left in while refactoring ocelot to phylink. Since priority flow control is disabled, writing the speed has no effect. Further, it was using ethtool.h SPEED_ instead of OCELOT_SPEED_ macros, which are incorrectly offset for GENMASK. Lastly, for priority flow control to properly function, some scenarios would rely on the rate adaptation from the PCS while the MAC speed would be fixed. So it isn't used, and even if it was, neither "speed" nor "mac_speed" are necessarily the correct values to be used. Fixes: e6e12df6 ("net: mscc: ocelot: convert to phylink") Signed-off-by:
-
Thomas Gleixner authored
lock_sock_fast() and lock_sock_nested() contain lockdep annotations for the sock::sk_lock.owned 'mutex'. sock::sk_lock.owned is not a regular mutex. It is just lockdep wise equivalent. In fact it's an open coded trivial mutex implementation with some interesting features. sock::sk_lock.slock is a regular spinlock protecting the 'mutex' representation sock::sk_lock.owned which is a plain boolean. If 'owned' is true, then some other task holds the 'mutex', otherwise it is uncontended. As this locking construct is obviously endangered by lock ordering issues as any other locking primitive it got lockdep annotated via a dedicated dependency map sock::sk_lock.dep_map which has to be updated at the lock and unlock sites. lock_sock_nested() is a straight forward 'mutex' lock operation: might_sleep(); spin_lock_bh(sock::sk_lock.slock) while (!try_lock(sock::sk_lock.owned)) { spin_unlock_bh(sock::sk_lock.slock); wait_for_release(); spin_lock_bh(sock::sk_lock.slock); } The lockdep annotation for sock::sk_lock.owned is for unknown reasons _after_ the lock has been acquired, i.e. after the code block above and after releasing sock::sk_lock.slock, but inside the bottom halves disabled region: spin_unlock(sock::sk_lock.slock); mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_); local_bh_enable(); The placement after the unlock is obvious because otherwise the mutex_acquire() would nest into the spin lock held region. But that's from the lockdep perspective still the wrong place: 1) The mutex_acquire() is issued _after_ the successful acquisition which is pointless because in a dead lock scenario this point is never reached which means that if the deadlock is the first instance of exposing the wrong lock order lockdep does not have a chance to detect it. 2) It only works because lockdep is rather lax on the context from which the mutex_acquire() is issued. Acquiring a mutex inside a bottom halves and therefore non-preemptible region is obviously invalid, except for a trylock which is clearly not the case here. This 'works' stops working on RT enabled kernels where the bottom halves serialization is done via a local lock, which exposes this misplacement because the 'mutex' and the local lock nest the wrong way around and lockdep complains rightfully about a lock inversion. The placement is wrong since the initial commit a5b5bb9a ("[PATCH] lockdep: annotate sk_locks") which introduced this. Fix it by moving the mutex_acquire() in front of the actual lock acquisition, which is what the regular mutex_lock() operation does as well. lock_sock_fast() is not that straight forward. It looks at the first glance like a convoluted trylock operation: spin_lock_bh(sock::sk_lock.slock) if (!sock::sk_lock.owned) return false; while (!try_lock(sock::sk_lock.owned)) { spin_unlock_bh(sock::sk_lock.slock); wait_for_release(); spin_lock_bh(sock::sk_lock.slock); } spin_unlock(sock::sk_lock.slock); mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_); local_bh_enable(); return true; But that's not the case: lock_sock_fast() is an interesting optimization for short critical sections which can run with bottom halves disabled and sock::sk_lock.slock held. This allows to shortcut the 'mutex' operation in the non contended case by preventing other lockers to acquire sock::sk_lock.owned because they are blocked on sock::sk_lock.slock, which in turn avoids the overhead of doing the heavy processing in release_sock() including waking up wait queue waiters. In the contended case, i.e. when sock::sk_lock.owned == true the behavior is the same as lock_sock_nested(). Semantically this shortcut means, that the task acquired the 'mutex' even if it does not touch the sock::sk_lock.owned field in the non-contended case. Not telling lockdep about this shortcut acquisition is hiding potential lock ordering violations in the fast path. As a consequence the same reasoning as for the above lock_sock_nested() case vs. the placement of the lockdep annotation applies. The current placement of the lockdep annotation was just copied from the original lock_sock(), now renamed to lock_sock_nested(), implementation. Fix this by moving the mutex_acquire() in front of the actual lock acquisition and adding the corresponding mutex_release() into unlock_sock_fast(). Also document the fast path return case with a comment. Reported-by:Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: netdev@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Alejandro Concepcion-Rodriguez authored
The file sja1105.txt was converted to nxp,sja1105.yaml. Signed-off-by:
Alejandro Concepcion-Rodriguez <asconcepcion@acoro.eu> Signed-off-by:
-
Randy Dunlap authored
When IGC=y and PTP_1588_CLOCK=m, the ptp_*() interface family is not available to the igc driver. Make this driver depend on PTP_1588_CLOCK_OPTIONAL so that it will build without errors. Various igc commits have used ptp_*() functions without checking that PTP_1588_CLOCK is enabled. Fix all of these here. Fixes these build errors: ld: drivers/net/ethernet/intel/igc/igc_main.o: in function `igc_msix_other': igc_main.c:(.text+0x6494): undefined reference to `ptp_clock_event' ld: igc_main.c:(.text+0x64ef): undefined reference to `ptp_clock_event' ld: igc_main.c:(.text+0x6559): undefined reference to `ptp_clock_event' ld: drivers/net/ethernet/intel/igc/igc_ethtool.o: in function `igc_ethtool_get_ts_info': igc_ethtool.c:(.text+0xc7a): undefined reference to `ptp_clock_index' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_feature_enable_i225': igc_ptp.c:(.text+0x330): undefined reference to `ptp_find_pin' ld: igc_ptp.c:(.text+0x36f): undefined reference to `ptp_find_pin' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_init': igc_ptp.c:(.text+0x11cd): undefined reference to `ptp_clock_register' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_stop': igc_ptp.c:(.text+0x12dd): undefined reference to `ptp_clock_unregister' ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe': Fixes: 64433e5b ("igc: Enable internal i225 PPS") Fixes: 60dbede0 ("igc: Add support for ethtool GET_TS_INFO command") Fixes: 87938851 ("igc: enable auxiliary PHC functions for the i225") Fixes: 5f295805 ("igc: Add basic skeleton for PTP") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Ederson de Souza <ederson.desouza@intel.com> Cc: Tony Nguyen <anthony.l.nguyen@intel.com> Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: intel-wired-lan@lists.osuosl.org Acked-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by:
-
Claudiu Manoil authored
The only struct dim_sample member that does not get initialized by dim_update_sample() is comp_ctr. (There is special API to initialize comp_ctr: dim_update_sample_with_comps(), and it is currently used only for RDMA.) comp_ctr is used to compute curr_stats->cmps and curr_stats->cpe_ratio (see dim_calc_stats()) which in turn are consumed by the rdma_dim_*() API. Therefore, functionally, the net_dim*() API consumers are not affected. Nevertheless, fix the computation of statistics based on an uninitialized variable, even if the mentioned statistics are not used at the moment. Fixes: ae0e6a5d ("enetc: Add adaptive interrupt coalescing") Signed-off-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
Claudiu Manoil authored
irq_set_affinity_hit() stores a reference to the cpumask_t parameter in the irq descriptor, and that reference can be accessed later from irq_affinity_hint_proc_show(). Since the cpu_mask parameter passed to irq_set_affinity_hit() has only temporary storage (it's on the stack memory), later accesses to it are illegal. Thus reads from the corresponding procfs affinity_hint file can result in paging request oops. The issue is fixed by the get_cpu_mask() helper, which provides a permanent storage for the cpumask_t parameter. Fixes: d4fd0404 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by:
-
Jason Wang authored
We try to use build_skb() if we had sufficient tailroom. But we forget to release the unused pages chained via private in big mode which will leak pages. Fixing this by release the pages after building the skb in big mode. Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Fixes: fb32856b ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Signed-off-by:
Jason Wang <jasowang@redhat.com> Reviewed-by:
-
Jan Beulich authored
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the special considerations for the head of the SKB no longer apply. Don't mistakenly report ERROR to the frontend for the first entry in the list, even if - from all I can tell - this shouldn't matter much as the overall transmit will need to be considered failed anyway. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
Paul Durrant <paul@xen.org> Signed-off-by:
-
