Pull "mvebu dt64 for 4.16 (part 3)" from Gregory CLEMENT:

Fix for the CP110 dt de-duplication series

* tag 'mvebu-dt64-4.16-3' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string

Other platforms' device-tree files start with a platform prefix, such as
sun7i-a20-*.dts or at91-*.dts.
This naming scheme turns out to be handy when using multi-platform build
systems such as OpenWrt.
Prepend oxnas files with their platform prefix to comply with the naming
scheme already used for most other platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:

arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000

As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:

arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18

It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.

Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:

arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000

arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000

arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000

[arnd: marked Cc:stable since this warning shows up with the latest dtc
       by default, and is more likely to actually cause problems than the
       other patches from this series]

Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

When replacing the cpm by cp0 and cps by cp1 [1] not only the label and
the alias were replaced but also the compatible string which was wrong.

Due to this the pinctrl driver was no more probed.

This patch fix it by reverting this change for the pinctrl compatible
string on Armada 8K.

[1]: "arm64: dts: marvell: replace cpm by cp0, cps by cp1"
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This fixes the following warning by also sending the flags argument for
gpio controllers:

Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000

Fixes: 8113ba91 ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f6 updated it incorrectly
while moving from platform code to DT. Fix it.

Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f6 ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The interrupt-parent of rtc was missing, add it.

Fixes: 8113ba91 ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":

arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])

Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt64-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM64 changes for v4.16, part 2

1. Fix DTC warnings around unit addresses.
2. Add SPDX license identifiers.

* tag 'samsung-dt64-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: Add SPDX license identifiers
  arm64: dts: exynos: Fix typo in MSCL clock controller unit address of Exynos5433
  arm64: dts: exynos: Use lower case hex addresses in node unit addresses
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM changes for 4.16, part 2

1. Add SPDX license identifiers.
2. Properly fix DTC warning for PMU/RTC interrupts on Exynos5410.

* tag 'samsung-dt-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: fix RTC interrupt for exynos5410
  Revert "ARM: dts: exynos: Add missing interrupt-controller properties to Exynos5410 PMU"
  ARM: dts: s5pv210: Add SPDX license identifiers
  ARM: dts: s3c64xx: Add SPDX license identifiers
  ARM: dts: s3c24xx: Add SPDX license identifiers
  ARM: dts: exynos: Add SPDX license identifiers
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner DT changes for 4.16, bis

A few improvements to our DT support, with:
  - basic DRM support for the A83t
  - simplefb support for the H3 and H5 SoCs
  - One fix for the USB ethernet on the Orange Pi R1

* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a711: Enable the LCD
  ARM: dts: sun8i: a83t: Add LVDS pins group
  ARM: dts: sun8i: a83t: Enable the PWM
  ARM: dts: sun8i: a83t: Add display pipeline
  ARM: sunxi: h3/h5: add simplefb nodes
  arm64: allwinner: h5: add compatible string for DE2 CCU
  ARM: sun8i: h3/h5: add DE2 CCU device node for H3
  dt-bindings: simplefb-sunxi: add pipelines for DE2
  ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Another round of 64-bit DT changes for the new Amlogic SoCs.  These
include IR, SPI and ethernet MAC support for the new AXG family SoCs.

* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-axg: enable ethernet for A113D S400 board
  ARM64: dts: meson-axg: add ethernet mac controller
  ARM64: dts: meson-axg: add the SPICC controller
  ARM64: dts: meson-axg: enable IR controller
  arm64: dts: meson-axg: switch uart_ao clock to CLK81
  clk: meson-axg: add clocks dt-bindings required header
  dt-bindings: clock: add compatible variant for the Meson-AXG
Signed-off-by: Olof Johansson <olof@lixom.net>

According to the comment added to exynos_dt_pmu_match[] in commit
8b283c02 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.

However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.

This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.

Fixes: e1e146b1 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

This reverts commit 6737b081.

Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC.  The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add axg compatible string and device tree bindings

* tag 'meson-clk-headers-for-v4.16-2' of git://github.com/BayLibre/clk-meson:
  clk: meson-axg: add clocks dt-bindings required header
  dt-bindings: clock: add compatible variant for the Meson-AXG

Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:

The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.

Besides them there are 2 other patches:
 - One adding the crypto support for Armada 37xx SoCs
 - An other adding Ethernet aliases on A7K/A8K base boards

* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: add Ethernet aliases
  arm64: dts: marvell: replace cpm by cp0, cps by cp1
  arm64: dts: marvell: de-duplicate CP110 description
  arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
  arm64: dts: marvell: use mvebu-icu.h where possible
  arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
  arm64: dts: marvell: fix typos in comment describing the NAND controller
  arm64: dts: marvell: use lower case for unit address and reg property
  arm64: dts: marvell: fix watchdog unit address in Armada AP806
  arm64: dts: marvell: armada-37xx: add a crypto node
  ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
  ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7

Merge tag 'imx-dt64-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "Freescale arm64 device tree updates for 4.16" from Shawn Guo:

 - LS1088A updates: add device support for DCFG, qoriq-mc, and USB.
 - Add power monitor device INA220 for ls208xa-rdb board.

* tag 'imx-dt64-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: ls208xa: add power monitor chip node
  arm64: dts: ls1088a: Add USB support
  arm64: dts: ls1088a: add fsl-mc hardware resource manager node
  arm64: dts: ls1088a: Added dcfg node in ls1088a dtsi

Merge tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "i.MX device tree changes for 4.16" from Shawn Guo:

 - A few random updates for vf610-zii board: correct switch EEPROM size,
   enable edma1, correct GPIO expander interrupt, add PHYs for switch2
   device.
 - LS1021A device tree updates: add reboot and QSPI device nodes, label
   USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
   setting, enable esdhc device, add Moxa UC-8410A board support.
 - A bunch of patches from Fabio: fix reg - unit address mismatches,
   remove leading zero in unit address, move regulators out of
   simple-bus, move nodes with no reg property out of bus, remove extra
   clock cell, add missing phy-cells to usb-nop-xceiv, etc.
 - A couple series from Hummingboard developers: re-organise device tree
   files for better handling various board versions, and then add the
   new hummingboard2 board support on top of that.
 - Disable AC'97 input pins pad and add support for powering off for
   imx6qdl-udoo board.
 - Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
   board.
 - Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
 - Add new board support of TS-4600 and TS-7970 from Technologic
   Systems.
 - A series from Stefan to update imx7-colibri device tree and then add
   new version of Toradex Colibri iMX7D board with eMMC support.
 - Other random updates on various board support.

* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
  ARM: dts: imx7s: Avoid using label in unit address and reg
  ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
  ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
  ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
  ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
  ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
  ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
  ARM: dts: vf610-zii-dev: enable edma1
  ARM: dts: ls1021a-twr: Remove extra clock cell
  ARM: dts: ls1021a-qds: Remove extra clock cell
  ARM: dts: imx53: add srtc node
  dt-bindings: imx-gpcv2: Fix the unit address
  ARM: imx: dts: Use lower case for bindings notation
  ARM: dts: imx6q-h100: use usdhc2 VSELECT
  ARM: dts: imx6sx: Add support for PCI power domain
  ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
  ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
  ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
  ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
  ARM: dts: imx6qdl-hummingboard2: add PWM3 support
  ...

Merge tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt

Pull "ASPEED device tree updates for 4.16" from Joel Stanley:

Clock driver support:

 Rework all platforms to use proper clock bindings. Linux should now boot
 upstream kernels on ast2400 and ast2500 platforms without out of tree
 patches.

New systems:

 Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
 Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
 Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400

 We also see updates to the Palmetto and Romulus systems to bring them in
 line with the functionality of those above.

 The systems take advantage of recently added drivers for LPC Snoop
 device and the PWM/Tachometer fan controller.

OpenBMC flash layout:

 The flash layout used OpenBMC systems is added and the device trees now
 use it.

* tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
  ARM: dts: aspeed-evb: Add unit name to memory node
  ARM: dts: aspeed-plametto: Add flash layout and fix memory node
  ARM: dts: aspeed-romulus: Update Romulus system
  ARM: dts: aspeed: Add Qanta Q71L BMC machine
  ARM: dts: aspeed: Add Ingrasys Zaius BMC machine
  ARM: dts: aspeed: Add Witherspoon BMC machine
  ARM: dts: aspeed: Sort ASPEED entries in makefile
  ARM: dts: Add OpenBMC flash layout
  ARM: dts: aspeed: Update license headers
  ARM: dts: aspeed: Remove skeleton.dtsi
  ARM: dts: aspeed: Add LPC Snoop device
  ARM: dts: aspeed: Add PWM and tachometer node
  ARM: dts: aspeed: Add clock phandle to GPIO
  ARM: dts: aspeed: Add flash controller clocks
  ARM: dts: aspeed: Add watchdog clocks
  ARM: dts: aspeed: Add MAC clocks
  ARM: dts: aspeed: Add proper clock references
  ARM: dts: aspeed: Add LPC and child devices
  dt-bindings: gpio: Add ASPEED constants
  dt-bindings: clock: Add ASPEED constants
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.

This commit is the result of:

 sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
 sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*

So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.

In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:

 - Base address of the registers is different for the "config-space"

 - Base address of the PCIe registers, MEM, CONF and IO areas were
   different

 - Labels (and phandles pointing to them) of the nodes were different
   ("cpm" prefix in the master CP, "cps" prefix in the slave CP)

This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.

We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.

There are a few aspects that deserve additional explanations:

 - PCIe needs to be handled separately because it is not part of the
   config-space {...} node, since it has registers outside of the
   range covered by config-space {...}.

 - We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
   they are used for the unit address part of some DT nodes. But since
   they are also used for the "reg" property of the same nodes, we
   have an ADDRESSIFY() macro that prepends 0x to those values.

We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:

 - the SDHCI controller that was only described in the master CP110 is
   now also described in the slave CP110. Even though the SDHCI
   controller from the slave CP110 is indeed not usable (as it isn't
   wired to the outside world) it is technically part of the silicon,
   and therefore it is reasonable to also describe it to be part of
   the slave CP110. In addition, if we wanted to get this correct for
   the SDHCI controller, we should also do it for the NAND controller,
   for which the situation is even more complicated: in a single CP110
   configuration (Armada 7K), the usable NAND controller is in the
   master CP110, while in a dual CP110 configuration (Armada 8K), the
   usable NAND controller is in the slave CP110. Since that would add
   a lot of additional complexity for no good reason, and since the IP
   blocks are in fact really present in both CPs, we simply describe
   them in both CPs at the DT level.

 - the cp110-master and cp110-slave nodes are now named cpm and
   cps. We could have kept cp110-master and cp110-slave, but that
   would have required adding another CP110_xyz define, which didn't
   seem very useful.

Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.

[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf

[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.

As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.

In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.

[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This fixes the following DTC warning:

  <stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This fixes the following DTC warning:

  Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:

If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.

Fixes: bb16ea17 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Merge tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman:

This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG
family of Amlogic SoCs.

* tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-axg: add new reset DT node
  ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC
  ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC
  documentation: Add compatibles for Amlogic Meson AXG pin controllers
  arm64: dts: meson-axg: add clock DT info for Meson AXG SoC

Merge tag 'qcom-dts-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm Device Tree Changes for v4.16" from Andy Gross:

* Add uSD slot nodes on msm8974-FP2 board

* tag 'qcom-dts-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: msm8974-FP2: Add uSD slot nodes