- 10 Aug, 2023 40 commits
-
-
Hans de Goede authored
Move ipu-bridge.h to include/media/, so that it can also be used by the atomisp code. Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Hans de Goede authored
Add a parse_sensor_fwnode() callback to ipu_bridge_init(), so that ipu_bridge_init() can be used with other sensor fwnode parse functions then just ipu_bridge_parse_ssdb(). This will allow the ipu3-bridge code to also be used by the atomisp driver. Signed-off-by:
Andy Shevchenko <andy@kernel.org> Signed-off-by:
-
Hans de Goede authored
sensor->adev is no longer dereferenced before it is permanently set by: sensor->adev = acpi_dev_get(adev); So the early assignment with a borrowed reference can be dropped. Signed-off-by:
-
Hans de Goede authored
The code to go from ACPI sensor info to a fwnode-tree with connector nodes and endpoint properties is 99% the same for the atomisp2 and the IPU3. The main difference is that atomisp2 devices do not have a SSDB table with various info. Abstract out the parsing of the sensor's ACPI fwnode into a helper function and store the parsed results, rather then the raw SSDB in struct ipu_sensor. This is a preparation patch for making the ipu-bridge code more generic so that it can be shared with the atomisp driver. Reviewed-by:
Daniel Scally <dan.scally@ideasonboard.com> Signed-off-by:
-
Hans de Goede authored
There is no need to keep a reference to the PLD struct around, it is only used once the get the sensor orientation. Make ipu_bridge_parse_orientation() also get + put the PLD. This is a preparation patch for making the ipu-bridge code more generic so that it can be shared with the atomisp driver. Reviewed-by:
-
Hans de Goede authored
Store the dev pointer in struct ipu_bridge instead of passing it around 3 levels deep. This takes up slightly more memory but further patches in this series add more data which needs to be passed around making passing everything as arguments cumbersome and those further patches also add data to struct ipu_bridge. To be consistent with these upcoming patches also add the dev pointer to struct ipu_bridge. Reviewed-by:
-
Hans de Goede authored
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names() where it belongs. And make the initialization of nodes[SWNODE_VCM] unconditional, ipu_bridge_init_swnode_group() takes care of not registering it when there is no VCM. Reviewed-by:
-
Hans de Goede authored
Move initialization of node_names.vcm to ipu_bridge_init_swnode_names() where it belongs. And make the initialization of nodes[SWNODE_VCM] unconditional, ipu_bridge_init_swnode_group() takes care of not registering it when there is no VCM. Reviewed-by:
-
Hans de Goede authored
Commit 567f97bd ("media: ipu3-cio2: support multiple sensors and VCMs with same HID") introduced an on stack vcm_name and then uses this for the name field of the software_node struct used for the vcm. But the software_node struct is much longer lived then the current stack-frame, so this is no good. Instead extend the ipu_node_names struct with an extra field to store the vcm software_node name and use that. Note this also changes the length of the allocated buffer from ACPI_ID_LEN + 4 to 16. the name is filled with "<ipu_vcm_types[x]>-%u" where ipu_vcm_types[x] is not an ACPI_ID. The maximum length of the strings in the ipu_vcm_types[] array is 11 + 5 bytes for "-255\0" means 16 bytes are needed in the worst case scenario. Fixes: 567f97bd ("media: ipu3-cio2: support multiple sensors and VCMs with same HID") Cc: Bingbu Cao <bingbu.cao@intel.com> Reviewed-by:
-
Hans de Goede authored
When ipu_bridge_parse_rotation() and ipu_bridge_parse_orientation() run sensor->adev is not set yet. So if either of the dev_warn() calls about unknown values are hit this will lead to a NULL pointer deref. Set sensor->adev earlier, with a borrowed ref to avoid making unrolling on errors harder, to fix this. Fixes: 485aa3df ("media: ipu3-cio2: Parse sensor orientation and rotation") Cc: Fabian Wüthrich <me@fabwu.ch> Signed-off-by:
-
Sakari Ailus authored
Replace a goto-based loop by a while loop. Suggested-by:
-
Niklas Söderlund authored
Add support for C-PHY on R-Car V4H. While the V4H supports both D-PHY and C-PHY this patch only adds support for the C-PHY mode due to lack of documentation and hardware to test on. The V4H is the first Gen4 device that is enabled in the rcar-csi2 driver. There is much overlap with the Gen3 driver, the primary difference is in how the receiver is started. The V4H have a much larger register space and some addresses overlap with Gen3. [Sakari Ailus: Use div_u64() to divide a 64-bit integer.] Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Jacopo Mondi authored
The imx219_set_pad_format() function adjusts the media bus code provided through the v4l2_subdev_format parameter to a media bus code known to be supported by the sensor. The same exact operation is performed by the imx219_get_format_code() function which called by imx219_update_pad_format(), which is in the imx219_set_pad_format() call path. Remove the duplicated operation and simplify imx219_set_pad_format(). Signed-off-by:
Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Jacopo Mondi authored
The set_fmt and init_cfg functions both fills a v4l2_mbus_framefmt instance, passing in the mode and the media bus code. While set_fmt uses function helpers, init_cfg open-codes the assignments. Simplify the format initialization by moving it to a common helper. Signed-off-by:
-
Jacopo Mondi authored
Port the imx219 sensor driver to use the subdev active state. Move all the format configuration to the subdevice state and simplify the format handling, locking and initialization. Signed-off-by:
-
Jacopo Mondi authored
The IMX219 is a RAW sensor. Fix the colorspace configuration by using V4L2_COLORSPACE_RAW and adjust the quantization and transfer function values. Drop ycbcr_enc as it doesn't apply to RAW sensors. Signed-off-by:
-
Jacopo Mondi authored
Complete the default format initialization in init_cfg() filling in the fields for the colorspace configuration copied from imx219_set_default_format(). Signed-off-by:
-
Jean-Michel Hautbois authored
Use the init_cfg pad level operation instead of the internal subdev open operation to set default formats on the pads. Signed-off-by:
Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com> Signed-off-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by:
-
Jean-Michel Hautbois authored
The imx219 is using the name "codes" for the mbus formats array. The name is too generic and not easy to read and follow in the code. Change it to imx219_mbus_formats. Signed-off-by:
Tommaso Merciai <tomm.merciai@gmail.com> Signed-off-by:
-
Hans de Goede authored
The helpers in this header are not used anywhere anymore, they have been superseded by the new CCI register access helpers. Reviewed-by:
-
Hans de Goede authored
Use the new comon CCI register access helpers to replace the private register access helpers in the ov2680 driver. While at it also switch to using the same register address defines as the standard drivers/media/i2c/ov2680.c driver to make merging the 2 drivers simpler. Reviewed-by:
-
Hans de Goede authored
Use the new comon CCI register access helpers to replace the private register access helpers in the imx290 driver. [Sakari Ailus: Squashed the patch to address a merge issue in Kconfig] Reviewed-by:
-
Hans de Goede authored
Use the new comon CCI register access helpers to replace the private register access helpers in the ov5693 driver. [Sakari Ailus: Squashed the patch to address a merge issue in Kconfig] Reviewed-by:
-
Hans de Goede authored
The CSI2 specification specifies a standard method to access camera sensor registers called "Camera Control Interface (CCI)". This uses either 8 or 16 bit (big-endian wire order) register addresses and supports 8, 16, 24 or 32 bit (big-endian wire order) register widths. Currently a lot of Linux camera sensor drivers all have their own custom helpers for this, often copy and pasted from other drivers. Add a set of generic helpers for this so that all sensor drivers can switch to a single common implementation. These helpers take an extra optional "int *err" function parameter, this can be used to chain a bunch of register accesses together with only a single error check at the end, rather than needing to error check each individual register access. The first failing call will set the contents of err to a non 0 value and all other calls will then become no-ops. Link: https://lore.kernel.org/linux-media/59aefa7f-7bf9-6736-6040-39551329cd0a@redhat.com/Reviewed-by:
-
Tomi Valkeinen authored
It is often useful to see when streaming for a device is being enabled or disabled. Add debug prints for this to v4l2_subdev_enable_streams() and v4l2_subdev_disable_streams(). Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by:
-
Tomi Valkeinen authored
The routing parameter of v4l2_subdev_set_routing_with_fmt() is missing 'const'. Add it. Signed-off-by:
-
Tomi Valkeinen authored
Now that the kernel drivers have been fixed to initialize the stream field, and we have the client capability which the userspace uses to say it has initialized the stream field, we can drop the implicit zeroing of the stream field in the various check functions. Signed-off-by:
-
Sakari Ailus authored
Split lens drivers from camera sensor into a new section. This makes it easier to maintain the list. Also add documentation related files under the camera sensor entry. Add the word "CAMERA" to the subject as well since there are many other kinds of sensors. Signed-off-by:
-
Sakari Ailus authored
Add an entry for V4L2 async and fwnode frameworks, with myself as the maintainer. Signed-off-by:
-
Sakari Ailus authored
As selecting V4L2_FWNODE, MEDIA_CONTROLLER and VIDEO_V4L2_SUBDEV_API are now selected by the top level menu, they can be dropped from the individual drivers. Also dropped selecting V4L2_ASYNC for a single driver as this is already implied by V4L2_FWNODE. Similarly, the I2C dependency is now also in the top level menu, so remove it, as well as VIDEO_DEV which isn't needed by camera sensor drivers. Signed-off-by:
-
Sakari Ailus authored
Select V4L2_FWNODE and VIDEO_V4L2_SUBDEV_API for all sensor drivers. This also adds the options to drivers that don't specifically need them, these are still seldom used drivers using old APIs. The upside is that these should now all compile --- many drivers have had missing dependencies. The "menu" is replaced by selectable "menuconfig" to select the needed V4L2_FWNODE and VIDEO_V4L2_SUBDEV_API options. Also select MEDIA_CONTROLLER which VIDEO_V4L2_SUBDEV_API effectively depends on, and add the I2C dependency to the menu. Reported-by:
-
Laurent Pinchart authored
Enumeration of the minimum, maximum and step values for the image width does not take hardware constraints into account. Fix it. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl>
-
Lukas Bulwahn authored
Commit cd063027 ("media: imx: Unstage the imx8mq-mipi-csi2 driver") adds a file entry for the driver code to MEDIA DRIVERS FOR FREESCALE IMX7/8, but misses the number '2' suffix in that entry. Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a broken reference. Correct the file entry in MEDIA DRIVERS FOR FREESCALE IMX7/8. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by:
-
Guoniu.zhou authored
i.MX93 uses a different gasket which has different register definitions compared with i.MX8. Hence implement the gasket callbacks in order to add ISI support for i.MX93. Signed-off-by:
Guoniu.zhou <guoniu.zhou@nxp.com> Reviewed-by:
-
Guoniu.zhou authored
The i.MX93 includes an ISI instance compatible with the imx8-isi driver, but with a different gasket. To prepare for this, make the gasket configuration modular by moving the code to an ops structure. Signed-off-by:
-
Guoniu.zhou authored
Add the compatible string support for i.MX93 ISI. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Yang Yingliang authored
It should check 'xbar->inputs', when allocate memory for it. Cc: stable@vger.kernel.org Fixes: cf21f328 ("media: nxp: Add i.MX8 ISI driver") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
-
Laurent Pinchart authored
CONFIG_VIDEO_IMX_MEDIA isn't needed on arm64 platforms since commit 9f257f50 ("media: imx: Unstage the imx7-media-csi driver") which moved the last arm64 driver depending on that Kconfig symbol out of staging. Drop it from the arm64 defconfig. Fixes: 9f257f50 ("media: imx: Unstage the imx7-media-csi driver") Signed-off-by:
-
Laurent Pinchart authored
The VIDEO_IMX_MEDIA Kconfig symbol used to select helpers shared between independent drivers for different i.MX SoCs, and VIDEO_IMX_MEDIA then selects drivers specific to the i.MX5 and i.MX6. Now that i.MX7 and i.MX8 support has moved to drivers/media/ and doesn't depend on VIDEO_IMX_CSI, there's no need to have separate Kconfig options. Merge VIDEO_IMX_CSI into VIDEO_IMX_MEDIA. Signed-off-by:
-
Tomi Valkeinen authored
FPD-Link has an operating mode that used to be called "asynchronous" in the hardware documentation, but that has been changed to non-synchronous already quite a while back. The ub960 driver still had one instance of the old naming, so let's rename it. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
