The majority of builds do not include HTE, so compile out hte
functionality unless CONFIG_HTE is selected.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Combine the polarity_change flag, struct line eflags, and hte enable
flag into a single flag variable.

The combination of these flags describes the configuration state
of the edge detector, so formalize and clarify that by combining
them into a single variable, edflags, in struct line.

The edflags is a subset of the GPIO_V2_LINE_FLAGsb relevant to
the edge detector, and is also a superset of the eflags it replaces.
The eflags name is still used to describe the subset of edflags
corresponding to the rising/falling edge flags where edflags is
masked down to that subset.

This consolidation reduces the number of variables being passed,
simplifies state comparisons, and provides a more extensible
foundation should additional edge sources be integrated in the
future.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Reorganise line event identification code to reduce code duplication,
and replace if-else initializers with a helper function to improve
readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Improve readability by replacing if-else chains with switch
statements.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Improve readability by using the GPIO_V2_LINE_FLAG_EDGE_BOTH instead
of combining the rising and falling edge flags.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Dipen Patel <dipenp@nvidia.com>
Tested-by: Dipen Patel <dipenp@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The edge detector is only ever started after the line desc has been
determined, so move edge_detector_stop() inside the line desc check,
and merge the two checked regions into one.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Dipen Patel <dipenp@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Remove checkpatch warnings. No functional changes.
Signed-off-by: Aakash Sen Sharma <aakashsensharma@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The SAMA5D2 PIOBU is only present on some AT91/Microchip SoCs.  Hence
add a dependency on ARCH_AT91, to prevent asking the user about this
driver when configuring a kernel without AT91/Microchip SoC support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

We should use of_node_get() when a new reference of device_node
is created. It is noted that the old reference stored in
'mm_gc->gc.of_node' should also be decreased.

This patch is based on the fact that there is a call site in function
'qe_add_gpiochips()' of src file 'drivers\soc\fsl\qe\gpio.c'. In this
function, of_mm_gpiochip_add_data() is contained in an iteration of
for_each_compatible_node() which will automatically increase and
decrease the refcount. So we need additional of_node_get() for the
reference escape in of_mm_gpiochip_add_data().

Fixes: a19e3da5 ("of/gpio: Kill of_gpio_chip and add members directly to gpio_chip")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Convert gpio-tpic2810 bindings to yaml format and remove outdated
bindings in .txt format.
Signed-off-by: Aparna M <a-m1@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Getting rid of checkpatch findings. No functional changes.
Signed-off-by: Shinyzenith <aakashsensharma@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Merge tag 'intel-gpio-v5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into TEST_MERGE

intel-gpio for v5.20-1

* Clean up the GPIO driver of Intel EG20 PCH

The following is an automated git shortlog grouped by driver:

pch:
 -  Change PCI device macros
 -  Use dev_err_probe()

Instead of open coding, use device_match_of_node() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Sort header inclusion alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

It's wrong to use defined string literal for three semantically different
cases, i.e.:
1) compatible string, which is part of ABI and has to have specific format;
2) I2C ID, which is user space visible and also ABI;
3) driver name, that can be changed.

Drop the define and use appropriate string literals in place.

While at it, drop comma at terminator entry of OF ID table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

There is nothing directly using of specific interfaces in this driver,
so lets not include the headers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add V2.1 rockchip gpio controller type, which is part of the
RK3588 SoC.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>

Allow usage of gpio-ranges with the rockchip gpio controller. The driver
already had support for this since it has been added to the mainline kernel
in the first place.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The PCA9571 very similar to the PCA9570, it only differs in the
number of GPIOs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

This patch adds device tree bindings for the NXP PCA9571,
a 8-bit I2C GPIO expander.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so chip is never NULL.

Also note that returning an error code from a remove callback doesn't
result in the device staying bound. It's still removed and devm
callbacks are called.

This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

priv cannot be NULL because brcmstb_gpio_probe() calls
platform_set_drvdata() with a non-NULL argument, so the check for !priv can
be dropped.

Also remove the variable ret that is only used to hide a bit that in the
end zero is returned.

This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

There is no user of these callbacks. The motivation for this change is
to stop returning an error code from the remove callback.

This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Returning a non-zero value in a platform driver's remove callback only
results in an error message ("remove callback returned a non-zero value.
This will be ignored.", see platform_remove()), and then the device is
removed anyhow.

As there was just a WARN_ON triggered, return 0 to drop the follow up
warning. The latter output is hardly relevant after the big WARN splat.

This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

There is no machine providing a teardown callback, so drop the unused
code.

This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Despite the name, R-Car V3U is the first member of the R-Car Gen4
family.  Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add support for system suspend/resume PM hooks, save the
register context of all the required gpio registers on suspend
and restore context on the resume.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The offset and marvell,pwm-offset properties weren't in the old binding.
Add them based on the existing usage in the driver and board DTS when
the marvell,armada-8k-gpio compatible is used.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Commit 5f79c651 ("arm: mvebu: use global interrupts for GPIOs on
Armada XP") the marvell,armadaxp-gpio compatible obsolete.

The driver code still exists to handle the armadaxp behaviour but all
the in-tree boards use the marvell,armada-370-gpio.  Document the
marvell,armadaxp-gpio compatible as deprecated.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Convert the existing device tree binding to DT schema format.

The old binding listed the interrupt-controller and related properties
as required but there are sufficiently many existing usages without it
that the YAML binding does not make the interrupt properties required.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The last user, which in fact was a dead code, has gone a year ago,
previous one 3 years ago. On top of that we want to drop away the
legacy GPIO APIs in the kernel, so take a chance to get rid of
unused devm_gpio_free() and accompanying stuff.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Pull intel drm build fix from Rodrigo Vivi:
 "Our 'dim' flow has a problem with fixes of fixes getting missed. We
  need to take a look on that later.

  Meanwhile, please allow me to quickly propagate this fix for the
  32-bit build issue here upstream"

* tag 'drm-intel-fixes-2022-07-17' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/ttm: fix 32b build

Merge tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix SIGSEGV when processing syscall args in perf.data files in 'perf
   trace'

 - Sync kvm, msr-index and cpufeatures headers with the kernel sources

 - Fix 'convert perf time to TSC' 'perf test':
     - No need to open events twice
     - Fix finding correct event on hybrid systems

* tag 'perf-tools-fixes-for-v5.19-2022-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf trace: Fix SIGSEGV when processing syscall args
  perf tests: Fix Convert perf time to TSC test for hybrid
  perf tests: Stop Convert perf time to TSC test opening events twice
  tools arch x86: Sync the msr-index.h copy with the kernel sources
  tools headers cpufeatures: Sync with the kernel sources
  tools headers UAPI: Sync linux/kvm.h with the kernel sources

Since segment_pages is no longer a compile time constant, it looks the
DIV_ROUND_UP(node->size, segment_pages) breaks the 32b build. Simplest
is just to use the ULL variant, but really we should need not need more
than u32 for the page alignment (also we are limited by that due to the
sg->length type), so also make it all u32.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: aff1e0b0 ("drm/i915/ttm: fix sg_table construction")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220712174050.592550-1-matthew.auld@intel.com
(cherry picked from commit 9306b2b2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Pull perf fix from Borislav Petkov:

 - A single data race fix on the perf event cleanup path to avoid
   endless loops due to insufficient locking

* tag 'perf_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix data race between perf_event_set_output() and perf_mmap_close()

Pull x86 fixes from Borislav Petkov:

 - Improve the check whether the kernel supports WP mappings so that it
   can accomodate a XenPV guest due to how the latter is setting up the
   PAT machinery

  - Now that the retbleed nightmare is public, here's the first round of
    fallout fixes:

      * Fix a build failure on 32-bit due to missing include

      * Remove an untraining point in espfix64 return path

      * other small cleanups

* tag 'x86_urgent_for_v5.19_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Remove apostrophe typo
  um: Add missing apply_returns()
  x86/entry: Remove UNTRAIN_RET from native_irq_return_ldt
  x86/bugs: Mark retbleed_strings static
  x86/pat: Fix x86_has_pat_wp()
  x86/asm/32: Fix ANNOTATE_UNRET_SAFE use on 32-bit

Pull gpio fix from Bartosz Golaszewski:

 - fix a configfs attribute of the gpio-sim module

* tag 'gpio-fixes-for-v5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix the chip_name configfs item