- 18 Jan, 2006 13 commits
-
-
Stephen Hemminger authored
Don't need to inline quite so many routines, let the compiler decide Signed-off-by:
Stephen Hemminger <shemminger@osdl.org> Signed-off-by:
Jeff Garzik <jgarzik@pobox.com>
-
Stephen Hemminger authored
Can use kzalloc here. Signed-off-by:
-
Stephen Hemminger authored
Make sure and rate limit all the error messages that might occur. If a problem occurs then a few messages are enough. Signed-off-by:
-
Stephen Hemminger authored
Small optimization, if dma addresses are 32 bits, then high bits are always zero. Signed-off-by:
Stephen Hemminger <shemminger@osdl.or> Signed-off-by:
-
Stephen Hemminger authored
Don't need to zero out the status ring entries after processing. Signed-off-by:
-
Stephen Hemminger authored
Be more careful about memory barriers. The only place we really need them is before and after updating the chip's ring interface. Signed-off-by:
-
Stephen Hemminger authored
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from sk98lin driver. Change how the ram buffer is divided up, and make the math clearer. Also, set the thresholds where rx takes precedence. The threshold values are just guesses at this point, it might be worth tuning them later. Signed-off-by:
-
Stephen Hemminger authored
Version update. Signed-off-by:
-
Stephen Hemminger authored
Need to call pci_set_consistent_dma_mask in the case of 64 bit DMA. Signed-off-by:
-
Stephen Hemminger authored
Need to make sure that sky2 receive buffers are 64 bit aligned. Also, don't need to start off with GFP_ATOMIC on initial setup. Signed-off-by:
-
Jesse Brandeburg authored
e100: e100 whitespace fixes These are whitespace only fixes. Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
John Ronciak <john.ronciak@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
e100: Handle the return values from pci_* functions This is to resolve warnings during compile time. Signed-off-by:
-
Jesse Brandeburg authored
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue) Set the end of list bit to cause the hardware's transmit state machine to work correctly and not prevent management (BMC) traffic. Signed-off-by:
-
- 17 Jan, 2006 27 commits
-
-
Javier Achirica authored
-
Jeff Kirsher authored
Signed-off-by:
-
Jeff Kirsher authored
Signed-off-by:
-
Jeff Kirsher authored
Improves small packet performance with large amounts of reassembly being done in the stack. Signed-off-by:
-
Jeff Kirsher authored
This was to fix compilation warnings. Also added log messages when pci_enable_* functions return with an error. Signed-off-by:
-
Jeff Kirsher authored
This is two patches, the first is adding additional bus information for the 8257{1|2|3} controllers. The second patch was orginally a community patch to print bus type/speed/width, and enhanced by us. Signed-off-by: -
Jeff Kirsher authored
The EEPROM image version is reported as a firmware version for these controllers. Signed-off-by:
-
Jeff Kirsher authored
Added 82571 fiber to WOL fix for dual port adapters. Added support for 82546GB (Quad Copper). Added PCIe typedef for x2, igp cable length 115, and extended TX CTRL registers. Added parity error detection and PCIe CTRL registers. Added EEPROM config registers. Signed-off-by:
-
Jeff Kirsher authored
Signed-off-by:
-
Jeff Kirsher authored
Signed-off-by:
-
Jeff Kirsher authored
Fixed an issue netpoll would error out during communication, generating the following error: --netdump[14973]: Got toomany timeouts in handshaking, ... Even after a kernel panic, netpoll requires two way communication to successfully transfer the crash log to the remote server. Signed-off-by:
-
Jeff Kirsher authored
Simplified the logic used to assign the frame_size. Signed-off-by:
-
Jeff Kirsher authored
Fixed VLAN support by switching control over to the firmware. Signed-off-by:
-
Jeff Kirsher authored
Fixed by moving code to correct location (for 82572 and 82571 controllers). Signed-off-by:
-
Jeff Kirsher authored
Fixed the collision distance for 82543 controllers and newer. Signed-off-by:
-
Jeff Kirsher authored
Removed duplicate code, TXDCTL and TXDCTL_COUNT_DESC are the same bit and there is no need to set it twice. Signed-off-by:
-
Jeff Kirsher authored
These were two separate community submitted patches. Signed-off-by:
-
Jeff Kirsher authored
Fixed the TX timeout logic to use "end of packet" rather than "next to clean". Updated message log. Signed-off-by:
-
Jeff Kirsher authored
This patch contains two fixes. The first fix is to the tx and rx descriptor rings clean up process. The second fix is to jumbo frames, which cleans up the code logic and removes most of the fifo related limitations on jumbo frames. This is because the driver code now supports splitting a packet across multiple descriptors. Signed-off-by:
-
Jeff Kirsher authored
10/100 speeds seem to have some problems reporting false tx timeouts especially at half duplex. Fixed by using a timeout factor to attempt to mitigate the false timeouts. Signed-off-by:
-
Jeff Kirsher authored
Fixed flow control water marks based on PBA size. Store flow control state in original_fc in addition to fc. Signed-off-by:
-
Jeff Kirsher authored
Fixed read_eeprom logic to test use_eerd instead of testing for 82573 controllers. Signed-off-by:
-
Jeff Kirsher authored
Signed-off-by:
-
Jeff Kirsher authored
Fixed the loopback logic to work for the PCI express adapters. Signed-off-by:
-
Jeff Kirsher authored
Fixed stats when using multiple queues. When multiple queues are enabled, log a message in syslog. Fixed memory allocation for multiple queues. Signed-off-by:
-
Jeff Kirsher authored
Fix adapter structure to handle multiple queues and prepping the driver for full multiple queue support, some changes are ifdef'd our unless you define CONFIG_E1000_MQ. Signed-off-by:
-
Jeff Kirsher authored
Fixed adapter identification issue. Signed-off-by:
-
