- 11 Feb, 2022 14 commits
-
-
Linus Walleij authored
Instead of providing our own homebrewn thermal measurement code for an NTC and passing tables, we put the NTC thermistor into the device tree, create a passive thermal zone, and poll this thermal zone for the temperature. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com>
-
Linus Walleij authored
We should terminate charging when we reach the voltage_max_design_uv not overvoltage_limit_uv, this is an abuse of that struct member. The overvoltage limit is actually not configurable on the AB8500, it is fixed to 4.75 V so drop a comment about that in the code. Fixes: 2a5f4183 ("power: supply: ab8500: Standardize voltages") Signed-off-by:
-
Linus Walleij authored
The BATCTRL mode reads the temperature of the battery by enabling a certain probing current (7-20 mA) and then measure the voltage of the NTC mounted inside the battery. None of the AB8500 product or the reference designs use this mode. What we use is the so-called BATTEMP mode which enables an internal 230 kOhm pull-up to 1.8 V to the external NTC on pin BatTemp (N16) and then measures the voltage over the NTC using the ADC: 1.8V (VTVOUT) | [ ] 230 kOhm | BatTemp +---------------- ADC Pin N16 | _ |/ [/] NTC _/| | GND Cut out the BATCTRL code to clear the forest and stop maintaining code we can never test. The current inducing method is still used to probe for the battery type using the internal BTI (battery type indicator) on the BatCtrl (C3) pin in a separate code path. Signed-off-by: -
Andy Shevchenko authored
Use device_property_string_array_count() to get number of strings in a string array property. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Uwe Kleine-König authored
When ret is not zero there were already one or two error messages emitted about a problem (because rt9455_register_reset() emits a message in most cases then). Passing on that error code to the i2c core only results in another error message. Suppress that by returning zero unconditionally. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Christophe JAILLET authored
Use devm_bitmap_zalloc() instead of hand writing it. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Hans de Goede authored
Add a new battery driver for the uPI uG3105 battery monitor. Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead it is expected to be use in combination with some always on microcontroller reading its coulomb-counter before it can wrap (must be read every 400 seconds!). Since Linux does not monitor coulomb-counter changes while the device is off or suspended, the coulomb counter is not used atm. So far this driver is only used on x86/ACPI (non devicetree) devs (also note there is no of_match table). Therefor there is no devicetree bindings documentation for this driver's "upisemi,rsns-microohm" property since this is not used in actual devicetree files and the dt bindings maintainers have requested properties with no actual dt users to _not_ be added to the dt bindings. The property's name has been chosen so that it should not need to be changed if/when devicetree enumeration support gets added later, as it mirrors "maxim,rsns-microohm" from the "maxim,max17042" bindings. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
If the fwnode data as parsed by power_supply_get_battery_info() provides max values for ccc_ireg and cvc_vreg then do not allow the user to later set these to higher values then those specified by the firmware, otherwise the battery might get damaged. Signed-off-by:
-
Hans de Goede authored
So far the bq24190_charger driver has been relying on either the chips default constant_charge_current_max_ua and constant_charge_voltage_max_uv values, or on the BIOS or bootloader to program these for us. This does not happen on all boards, causing e.g. the wrong (too low) values to be used on Lenovo Yoga Tablet 2 830F/L and 1050F/L tablets. If power_supply_get_battery_info() provides us with values for these settings, then program the charger accordingly. And if the user later overrides these values then save the user-values so that these will be restored after a suspend/resume. Signed-off-by:
-
Hans de Goede authored
Store ichg-max and vreg-max in bq24190_dev_info once from bq24190_get_config() and drop the bq24190_charger_get_current_max() and bq24190_charger_get_voltage_max() helpers. This is a preparation patch for honoring the constant_charge_current_max_ua and constant_charge_voltage_max_uv values from power_supply_get_battery_info(). Signed-off-by:
-
Hans de Goede authored
power_supply_get_battery_info() now also supports getting battery_info on boards not using dt/of. Remove the of_node check. If neither of nor other battery-info is present the function will fail making this change a no-op in that case. Signed-off-by:
-
Hans de Goede authored
Turn off the 5V boost regulator on shutdown, there are 3 reasons for doing this: 1. It drains he battery if left on 2. If left on the device will not charge when plugged into a charger 3. If left on and the powered peripheral attached to a Type-C port is removed before the next boot, then the Type-C port-controller will see VBus being present while nothing is attached confusing the TCPM state-machine. Signed-off-by:
-
Hans de Goede authored
Add support to power_supply_get_battery_info() to read the properties from other fwnode types such as swnodes added by platform code on x86 devices. Signed-off-by:
-
Hans de Goede authored
Switch power_supply_get_battery_info() over to use the generic fwnode_property_*() property read functions. This is a preparation patch for adding support for reading properties from other fwnode types such as swnode properties added by platform code on x86 devices. Note the parsing of the 2d matrix "ocv-capacity-table-%d" and "resistance-temp-table" properties is not converted since this depends on the raw of_get_property() accessor function of which there is no fwnode_property_*() equivalent AFAICT. This means that these properties will not be supported in swnodes for now. Signed-off-by:
-
- 02 Feb, 2022 1 commit
-
-
Colin Ian King authored
There is a spelling mistake in a MODULE_PARM_DESC description. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Acked-by:
-
- 01 Feb, 2022 25 commits
-
-
Sebastian Reichel authored
Immutable branch between power-supply, mfd, i2c and extcon for for 5.18 This immutable branch fixes the charger setup on Xiaomi Mi Pad 2 and Lenovo Yogabook, which requires updates to multiple drivers throughout the tree. Signed-off-by:Sebastian Reichel <sre@kernel.org>
-
Hans de Goede authored
Make cht_wc_extcon_get_id() report RID_A for ACA adapters, instead of reporting ID_FLOAT. According to the spec. we should read the USB-ID pin ADC value to determine the resistance of the used pull-down resister and then return RID_A / RID_B / RID_C based on this. But all "Accessory Charger Adapter"s (ACAs) which users can actually buy always use a combination of a charging port with one or more USB-A ports, so they should always use a resistor indicating RID_A. But the spec is hard to read / badly-worded so some of them actually indicate they are a RID_B ACA even though they clearly are a RID_A ACA. To workaround this simply always return INTEL_USB_RID_A, which matches all the ACAs which users can actually buy. Acked-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Hans de Goede authored
The bq25890 used on the Yogabook YB1-X90 / -X91 models relies on the extcon-driver's BC-1.2 charger detection, and the bq25890 driver expect this info to be available through a parent power_supply class-device which models the detected charger (idem to how the Type-C TCPM code registers a power_supply classdev for the connected charger). Add support for registering the power_supply class-device expected by this setup. Acked-by:
-
Hans de Goede authored
This is a preparation patch for adding support for registering a power_supply class device. Setting usbsrc to "CHT_WC_USBSRC_TYPE_SDP << CHT_WC_USBSRC_TYPE_SHIFT" will make the following switch-case return EXTCON_CHG_USB_SDP just as before, so there is no functional change. Acked-by:
-
Hans de Goede authored
So far the extcon-intel-cht-wc code has only been tested on devices with a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support through a FUSB302 Type-C controller. Some devices with the intel-cht-wc PMIC however come with an USB-micro-B connector, or an USB-2 only Type-C connector without USB-PD. Which device-model we are running on can be identified with the new cht_wc_model intel_soc_pmic field. On models without a Type-C controller the extcon code must control the Vbus 5V boost converter and the USB role switch depending on the detected cable-type. Acked-by:
-
Hans de Goede authored
The CHT_WC_VBUS_GPIO_CTLO GPIO actually driving an external 5V Vboost converter for Vbus depends on the board on which the Cherry Trail - Whiskey Cove PMIC is actually used. Since the information about the exact PMIC setup is necessary in other places too, struct intel_soc_pmic now has a new cht_wc_model field indicating the board model. Only poke the CHT_WC_VBUS_GPIO_CTLO GPIO if this new field is set to INTEL_CHT_WC_GPD_WIN_POCKET, which indicates the Type-C (with PD and DP-altmode) setup used on the GPD pocket and GPD win; and on which this GPIO actually controls an external 5V Vboost converter. Acked-by:
-
Hans de Goede authored
The i2c-controller on the Cherry Trail - Whiskey Cove PMIC is special in that it is always connected to the I2C charger IC of the board on which the PMIC is used; and the charger IC is not described in ACPI, so the i2c-cht-wc code needs to instantiate an i2c-client for it itself. So far this was hardcoded to instantiate an i2c-client for the bq24292i, with all properties, etc. set to match how this charger is used on the GPD win and GPD pocket devices. There is a rudimentary check to make sure the ACPI tables are at least somewhat as expected, but this is far from accurate, leading to a wrong i2c-client being instantiated for the charger on some boards. Switch to the new DMI based intel_cht_wc_get_model() helper which is exported by the MFD driver for the CHT Whiskey Cove PMIC to help PMIC cell drivers like the i2c-cht-wc code reliably detect which board they are running on. And add board_info for the charger ICs as found on the other 2 known boards with a Whisky Cove PMIC. This has been tested on all 3 known boards. Acked-by:
Wolfram Sang <wsa@kernel.org> Reviewed-by:
-
Hans de Goede authored
Tablet / laptop designs using an Intel Cherry Trail x86 main SoC with an Intel Whiskey Cove PMIC do not use a single standard setup for the charger, fuel-gauge and other chips surrounding the PMIC / charging+data USB port. Unlike what is normal on x86 this diversity in designs is not handled by the ACPI tables. On 2 of the 3 known designs there are no standard (PNP0C0A) ACPI battery devices and on the 3th design the ACPI battery device does not work under Linux due to it requiring non-standard and undocumented ACPI behavior. So to make things work under Linux we use native charger and fuel-gauge drivers on these devices, re-using the native drivers used on ARM boards with the same charger / fuel-gauge ICs. This requires various MFD-cell drivers for the CHT-WC PMIC cells to know which model they are exactly running on so that they can e.g. instantiate an I2C-client for the right model charger-IC (the charger is connected to an I2C-controller which is part of the PMIC). Rather then duplicating DMI-id matching to check which model we are running on in each MFD-cell driver, add a check for this to the shared drivers/mfd/intel_soc_pmic_chtwc.c code by using a DMI table for all 3 known models: 1. The GPD Win and GPD Pocket mini-laptops, these are really 2 models but the Pocket re-uses the GPD Win's design in a different housing: The WC PMIC is connected to a TI BQ24292i charger, paired with a Maxim MAX17047 fuelgauge + a FUSB302 USB Type-C Controller + a PI3USB30532 USB switch, for a fully functional Type-C port. 2. The Xiaomi Mi Pad 2: The WC PMIC is connected to a TI BQ25890 charger, paired with a TI BQ27520 fuelgauge, using the TI BQ25890 for BC1.2 charger type detection, for a USB-2 only Type-C port without PD. 3. The Lenovo Yoga Book YB1-X90 / Lenovo Yoga Book YB1-X91 series: The WC PMIC is connected to a TI BQ25892 charger, paired with a TI BQ27542 fuelgauge, using the WC PMIC for BC1.2 charger type detection and using the BQ25892's Mediatek Pump Express+ (1.0) support to enable charging with up to 12V through a micro-USB port. Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Hans de Goede authored
Use the devm_regmap_field_bulk_alloc() helper function instead of open-coding this ourselves. Reviewed-by:
-
Yauhen Kharuzhy authored
Add a "linux,pump-express-vbus-max" property which indicates if the Pump Express+ protocol should be used to increase the charging protocol. If this new property is set and a DCP charger is detected then request a higher charging voltage through the Pump Express+ protocol. So far this new property is only used on x86/ACPI (non devicetree) devs, IOW it is not used in actual devicetree files. The devicetree-bindings maintainers have requested properties like these to not be added to the devicetree-bindings, so the new property is deliberately not added to the existing devicetree-bindings. Changes by Hans de Goede: - Port to my bq25890 patch-series + various cleanups - Make behavior configurable through a new "linux,pump-express-vbus-max" device-property - Sleep 1 second before re-checking the Vbus voltage after requesting it to be raised, to ensure that the ADC has time to sampled the new Vbus - Add VBUSV bq25890_tables[] entry and use it in bq25890_get_vbus_voltage() - Tweak commit message Signed-off-by:
Yauhen Kharuzhy <jekhor@gmail.com> Reviewed-by:
-
Hans de Goede authored
The bq25892 does not have builtin charger-type detection like the bq25980, there might be some external charger detection capability, which will be modelled as a power_supply class-device supplying the bq25892. Use the usb_type property value from the supplier psy-device to set the input-current-limit (when available). Reviewed-by:
-
Hans de Goede authored
The bq25890_charger code supports enabling/disabling the boost converter based on usb-phy notifications. But the usb-phy framework is not used on all boards/platforms. At support for registering the Vbus boost converter as a standard regulator when there is no usb-phy on the board. Also add support for providing regulator_init_data through platform_data for use on boards where device-tree is not used and the platform code must thus provide the regulator_init_data. Reviewed-by:
-
Hans de Goede authored
Add a bq25890_set_otg_cfg() helper function, this is a preparation patch for adding regulator support. Reviewed-by:
-
Hans de Goede authored
Drop the "if (!dev->platform_data)" check, this seems to be an attempt for allowing loading the driver on devices without devicetree stemming from the initial commit of the driver (with the presumed intention being the "return -ENODEV" else branch getting replaced with something else). With the new "linux,skip-init" and "linux,read-back-settings" properties the driver can actually supports devices without devicetree and this check no longer makes sense. While at it, also switch to dev_err_probe(), which is already used in various other places in the driver. Reviewed-by:
-
Hans de Goede authored
On boards where the "linux,skip-reset" boolean property is set we don't reset the charger; and on some boards where the fw takes care of initalizition F_CHG_CFG is set to 0 before handing control over to the OS. Explicitly set F_CHG_CFG to 1 on boards where we don't reset the charger, so that charging is always enabled on these boards, like it is always enabled on boards where we do reset the charger. Reviewed-by:
-
Hans de Goede authored
On most x86/ACPI devices there is no devicetree to supply the necessary init-data. Instead the firmware already fully initializes the bq25890 charger at boot. To support this, add support for reading back the settings from the chip through a new "linux,read-back-settings" boolean. So far this new property is only used on x86/ACPI (non devicetree) devs, IOW it is not used in actual devicetree files. The devicetree-bindings maintainers have requested properties like these to not be added to the devicetree-bindings, so the new property is deliberately not added to the existing devicetree-bindings. Reviewed-by:
-
Hans de Goede authored
On most x86/ACPI devices the firmware already fully initializes the bq25890 charger at boot, in this case it is best to not reset it at probe() time. At support for a new "linux,skip-reset" boolean property to support this. So far this new property is only used on x86/ACPI (non devicetree) devs, IOW it is not used in actual devicetree files. The devicetree-bindings maintainers have requested properties like these to not be added to the devicetree-bindings, so the new property is deliberately not added to the existing devicetree-bindings. Reviewed-by:
-
Hans de Goede authored
On most x86/ACPI devices there is no devicetree to supply the necessary init-data. Instead the firmware already fully initializes the bq25890 charger at boot. Factor out the current code to write all the init_data from devicetree into a new bq25890_rw_init_data() helper which can both write the data to the charger (the current behavior) as well as read it back from the charger into the init_data struct. This is a preparation patch for adding support for x86/ACPI device's where the init_data must be read back from the bq25890 charger. Reviewed-by:
-
Yauhen Kharuzhy authored
Take into account possible current reduction due to low-temperature when reading POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX. As described in the datasheet in cool (0-20° Celcius) conditions the current limit is decreased to 20% or 50% of ICHG field value depended on JEITA_ISET field. Also add NTC_FAULT field value to the debug message in bq25890_get_chip_state(). Changed by Hans de Goede: - Fix reading F_CHG_FAULT instead of F_NTC_FIELD for state->ntc_fault - Only read JEITA_ISET field if necessary - Tweak commit message a bit Signed-off-by:
-
Yauhen Kharuzhy authored
Rename the Input Current Limit field in the REG00 from IILIM to IINLIM accordingly with the bq2589x datasheet. This is just cosmetical change to reduce confusion. Signed-off-by:
-
Hans de Goede authored
Some (USB) charger ICs have variants with USB D+ and D- pins to do their own builtin charger-type detection, like e.g. the bq24190 and bq25890 and also variants which lack this functionality, e.g. the bq24192 and bq25892. In case the charger-type; and thus the input-current-limit detection is done outside the charger IC then we need some way to communicate this to the charger IC. In the past extcon was used for this, but if the external detection does e.g. full USB PD negotiation then the extcon cable-types do not convey enough information. For these setups it was decided to model the external charging "brick" and the parameters negotiated with it as a power_supply class-device itself; and power_supply_set_input_current_limit_from_supplier() was introduced to allow drivers to get the input-current-limit this way. But in some cases psy drivers may want to know other properties, e.g. the bq25892 can do "quick-charge" negotiation by pulsing its current draw, but this should only be done if the usb_type psy-property of its supplier is set to DCP (and device-properties indicate the board allows higher voltages). Instead of adding extra helper functions for each property which a psy-driver wants to query from its supplier, refactor power_supply_set_input_current_limit_from_supplier() into a more generic power_supply_get_property_from_supplier() function. Reviewed-by:
-
Hans de Goede authored
Some boards with an AXP288 fuel-gauge appear to have a broken (approx. 2 milli-ohm instead of 10) current sense resistor. This makes the coulomb-counter part of the fuel-gauge useless, but the OCV based capacity reporting is still working. Add a no_current_sense_res module_param to disable use of the coulomb-counter using parts of the fuel-gauge to allow users to work around this. Note this is a module parameter and not done through DMI quirks, since this seems to be a defect on some boards, not something which all boards of the same model share. Signed-off-by:
-
Hans de Goede authored
The valid flag is protected by the mutex, so code clearing it should take the mutex before cleating the valid flag. Signed-off-by:
-
Hans de Goede authored
Refactor the IRQ initialization code: * Move the looking up of the vIRQs to the beginning of probe(), failing probe early if this fails * Do the actual requesting of IRQs inline in probe() and properly abort probe() on errors * Use devm_request_threaded_irq(), completing the conversion of probe() to only use devm managed resources and remove the remove() driver function. Signed-off-by:
-
Hans de Goede authored
Use devm_power_supply_register() instead of power_supply_register(). Note as a side-effect this changes the release order so that now first the IRQs get free-ed and then the psy gets unregistered. This is actually a bug-fix since this fixes the IRQ possibly trying to reference the unregistered psy. Signed-off-by:
-
