So far no error is returned from a failing transmission. However it
might sometimes be useful, and particularly easy to use during sync
transfers (for certain MLME commands). Let's create an internal variable
for that, global to the device. Right now only success are registered,
which is rather useless, but soon we will have more situations filling
this field.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220407100903.1695973-4-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

There are more codes than already listed, let's be a bit more
exhaustive. This will allow to drop device drivers local definitions of
these codes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220407100903.1695973-3-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Let's keep these definitions as close to the specification as possible
while they are not yet in use. The names get slightly longer, but we
gain the minor cost of being able to search the spec more easily.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220407100903.1695973-2-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

The core now knows how to set the symbol duration in a few cases, when
drivers correctly advertise the protocols used on each channel. For
these drivers, there is no more need to bother with symbol duration,
lifs and sifs periods so just drop the duplicated code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-5-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

As depicted in the IEEE 802.15.4 specification, modulation/bands are
tight to a number of page/channels so we can for most of them derive the
durations automatically.

The two locations that must call this new helper to set the variou
symbol durations are:
- when manually requesting a channel change though the netlink interface
- at PHY creation, once the device driver has set the default
  page/channel

If an information is missing, the symbol duration is not touched, a
debug message is eventually printed. This keeps the compatibility with
the unconverted drivers for which it was too complicated for me to find
their precise information. If they initially provided a symbol duration,
it would be kept. If they don't, the symbol duration value is left
untouched.

Once the symbol duration derived, the lifs and sifs durations are
updated as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-4-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Tdsym is often given in the spec as pretty small numbers in microseconds
and hence was reflected in the code as symbol_duration and was stored as
a u8. Actually, for UWB PHYs, the symbol duration is given in
nanoseconds and are as precise as picoseconds. In order to handle better
these PHYs, change the type of symbol_duration to u32 and store this
value in nanoseconds.

All the users of this variable are updated in a mechanical way.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-3-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with the symbol_duration in order to get these
values in microseconds.

Fixes: ded845a7 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220201180629.93410-2-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Merge tag 'ieee802154-for-davem-2022-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next

Stefan Schmidt says:

====================
pull-request: ieee802154-next 2022-02-10

An update from ieee802154 for your *net-next* tree.

There is more ongoing in ieee802154 than usual. This will be the first pull
request for this cycle, but I expect one more. Depending on review and rework
times.

Pavel Skripkin ported the atusb driver over to the new USB api to avoid unint
problems as well as making use of the modern api without kmalloc() needs in he
driver.

Miquel Raynal landed some changes to ensure proper frame checksum checking with
hwsim, documenting our use of wake and stop_queue and eliding a magic value by
using the proper define.

David Girault documented the address struct used in ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2022-02-09

This series contains updates to ice driver only.

Brett adds support for QinQ. This begins with code refactoring and
re-organization of VLAN configuration functions to allow for
introduction of VSI VLAN ops to enable setting and calling of
respective operations based on device support of single or double
VLANs. Implementations are added for outer VLAN support.

To support QinQ, the device must be set to double VLAN mode (DVM).
In order for this to occur, the DDP package and NVM must also support
DVM. Functions to determine compatibility and properly configure the
device are added as well as setting the proper bits to advertise and
utilize the proper offloads. Support for VIRTCHNL_VF_OFFLOAD_VLAN_V2
is also included to allow for VF to negotiate and utilize this
functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

1) Conntrack sets on CHECKSUM_UNNECESSARY for UDP packet with no checksum,
   from Kevin Mitchell.

2) skb->priority support for nfqueue, from Nicolas Dichtel.

3) Remove conntrack extension register API, from Florian Westphal.

4) Move nat destroy hook to nf_nat_hook instead, to remove
   nf_ct_ext_destroy(), also from Florian.

5) Wrap pptp conntrack NAT hooks into single structure, from Florian Westphal.

6) Support for tcp option set to noop for nf_tables, also from Florian.

7) Do not run x_tables comment match from packet path in nf_tables,
   from Florian Westphal.

8) Replace spinlock by cmpxchg() loop to update missed ct event,
   from Florian Westphal.

9) Wrap cttimeout hooks into single structure, from Florian.

10) Add fast nft_cmp expression for up to 16-bytes.

11) Use cb->ctx to store context in ctnetlink dump, instead of using
    cb->args[], from Florian Westphal.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
  netfilter: ctnetlink: use dump structure instead of raw args
  nfqueue: enable to set skb->priority
  netfilter: nft_cmp: optimize comparison for 16-bytes
  netfilter: cttimeout: use option structure
  netfilter: ecache: don't use nf_conn spinlock
  netfilter: nft_compat: suppress comment match
  netfilter: exthdr: add support for tcp option removal
  netfilter: conntrack: pptp: use single option structure
  netfilter: conntrack: remove extension register api
  netfilter: conntrack: handle ->destroy hook via nat_ops instead
  netfilter: conntrack: move extension sizes into core
  netfilter: conntrack: make all extensions 8-byte alignned
  netfilter: nfqueue: enable to get skb->priority
  netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY
====================

Link: https://lore.kernel.org/r/20220209133616.165104-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit
   9652dc2e ("tcp: relax listening_hash operations")

removed the need to disable bottom half while acquiring
listening_hash.lock. There are still two callers left which disable
bottom half before the lock is acquired.

On PREEMPT_RT the softirqs are preemptible and local_bh_disable() acts
as a lock to ensure that resources, that are protected by disabling
bottom halves, remain protected.
This leads to a circular locking dependency if the lock acquired with
disabled bottom halves is also acquired with enabled bottom halves
followed by disabling bottom halves. This is the reverse locking order.
It has been observed with inet_listen_hashbucket::lock:

local_bh_disable() + spin_lock(&ilb->lock):
  inet_listen()
    inet_csk_listen_start()
      sk->sk_prot->hash() := inet_hash()
	local_bh_disable()
	__inet_hash()
	  spin_lock(&ilb->lock);
	    acquire(&ilb->lock);

Reverse order: spin_lock(&ilb2->lock) + local_bh_disable():
  tcp_seq_next()
    listening_get_next()
      spin_lock(&ilb2->lock);
	acquire(&ilb2->lock);

  tcp4_seq_show()
    get_tcp4_sock()
      sock_i_ino()
	read_lock_bh(&sk->sk_callback_lock);
	  acquire(softirq_ctrl)	// <---- whoops
	  acquire(&sk->sk_callback_lock)

Drop local_bh_disable() around __inet_hash() which acquires
listening_hash->lock. Split inet_unhash() and acquire the
listen_hashbucket lock without disabling bottom halves; the inet_ehash
lock with disabled bottom halves.
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/12d6f9879a97cd56c09fb53dee343cbb14f7f1f7.camel@gmx.de
Link: https://lkml.kernel.org/r/X9CheYjuXWc75Spa@hirez.programming.kicks-ass.net
Link: https://lore.kernel.org/r/YgQOebeZ10eNx1W6@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf-next 2022-02-09

We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).

The main changes are:

1) Add custom BPF allocator for JITs that pack multiple programs into a huge
   page to reduce iTLB pressure, from Song Liu.

2) Add __user tagging support in vmlinux BTF and utilize it from BPF
   verifier when generating loads, from Yonghong Song.

3) Add per-socket fast path check guarding from cgroup/BPF overhead when
   used by only some sockets, from Pavel Begunkov.

4) Continued libbpf deprecation work of APIs/features and removal of their
   usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
   and various others.

5) Improve BPF instruction set documentation by adding byte swap
   instructions and cleaning up load/store section, from Christoph Hellwig.

6) Switch BPF preload infra to light skeleton and remove libbpf dependency
   from it, from Alexei Starovoitov.

7) Fix architecture-agnostic macros in libbpf for accessing syscall
   arguments from BPF progs for non-x86 architectures,
   from Ilya Leoshkevich.

8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
   of 16-bit field with anonymous zero padding, from Jakub Sitnicki.

9) Add new bpf_copy_from_user_task() helper to read memory from a different
   task than current. Add ability to create sleepable BPF iterator progs,
   from Kenny Yu.

10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
    utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.

11) Generate temporary netns names for BPF selftests to avoid naming
    collisions, from Hangbin Liu.

12) Implement bpf_core_types_are_compat() with limited recursion for
    in-kernel usage, from Matteo Croce.

13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
    to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.

14) Misc minor fixes to libbpf and selftests from various folks.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
  selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
  bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
  libbpf: Fix compilation warning due to mismatched printf format
  selftests/bpf: Test BPF_KPROBE_SYSCALL macro
  libbpf: Add BPF_KPROBE_SYSCALL macro
  libbpf: Fix accessing the first syscall argument on s390
  libbpf: Fix accessing the first syscall argument on arm64
  libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
  selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
  libbpf: Fix accessing syscall arguments on riscv
  libbpf: Fix riscv register names
  libbpf: Fix accessing syscall arguments on powerpc
  selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
  libbpf: Add PT_REGS_SYSCALL_REGS macro
  selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
  bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
  bpf: Fix leftover header->pages in sparc and powerpc code.
  libbpf: Fix signedness bug in btf_dump_array_data()
  selftests/bpf: Do not export subtest as standalone test
  bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
  ...
====================

Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In the commit c504e5c2 ("net: skb: introduce kfree_skb_reason()")
drop reason is introduced to the tracepoint of kfree_skb. Therefore,
drop_monitor is able to report the drop reason to users by netlink.

The drop reasons are reported as string to users, which is exactly
the same as what we do when reporting it to ftrace.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220209060838.55513-1-imagedong@tencent.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Sitnicki says:

====================

Following the recent split-up of the bpf_sock dst_port field, apply the same to
technique to the bpf_sk_lookup remote_port field to make uAPI more user
friendly.

v1 -> v2:
- Remove remote_port range check and cast to be16 in TEST_RUN for sk_lookup
  (kernel test robot)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Extend the context access tests for sk_lookup prog to cover the surprising
case of a 4-byte load from the remote_port field, where the expected value
is actually shifted by 16 bits.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220209184333.654927-3-jakub@cloudflare.com

remote_port is another case of a BPF context field documented as a 32-bit
value in network byte order for which the BPF context access converter
generates a load of a zero-padded 16-bit integer in network byte order.

First such case was dst_port in bpf_sock which got addressed in commit
4421a582 ("bpf: Make dst_port field in struct bpf_sock 16-bit wide").

Loading 4-bytes from the remote_port offset and converting the value with
bpf_ntohl() leads to surprising results, as the expected value is shifted
by 16 bits.

Reduce the confusion by splitting the field in two - a 16-bit field holding
a big-endian integer, and a 16-bit zero-padding anonymous field that
follows it.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220209184333.654927-2-jakub@cloudflare.com

VFs by default are able to see all tagged traffic regardless of trust
and VLAN filters. Based on legacy devices (i.e. ixgbe, i40e), customers
expect VFs to receive all VLAN tagged traffic with a matching
destination MAC.

Add an ethtool private flag 'vf-vlan-pruning' and set the default to
off so VFs will receive all VLAN traffic directed towards them. When
the flag is turned on, VF will only be able to receive untagged
traffic or traffic with VLAN tags it has created interfaces for.

Also, the flag cannot be changed while any VFs are allocated. This was
done to simplify the implementation. So, if this flag is needed, then
the PF admin must enable it. If the user tries to enable the flag while
VFs are active, then print an unsupported message with the
vf-vlan-pruning flag included. In case multiple flags were specified, this
makes it clear to the user which flag failed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently there is only support for 802.1Q port VLANs on SR-IOV VFs. Add
support to also allow 802.1ad port VLANs when double VLAN mode is
enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In order for the driver to support 802.1ad VLAN filtering and offloads,
it needs to advertise those VLAN features and also support modifying
those VLAN features, so make the necessary changes to
ice_set_netdev_features(). By default, enable CTAG insertion/stripping
and CTAG filtering for both Single and Double VLAN Modes (SVM/DVM).
Also, in DVM, enable STAG filtering by default. This is done by
setting the feature bits in netdev->features. Also, in DVM, support
toggling of STAG insertion/stripping, but don't enable them by
default. This is done by setting the feature bits in
netdev->hw_features.

Since 802.1ad VLAN filtering and offloads are only supported in DVM, make
sure they are not enabled by default and that they cannot be enabled
during runtime, when the device is in SVM.

Add an implementation for the ndo_fix_features() callback. This is
needed since the hardware cannot support multiple VLAN ethertypes for
VLAN insertion/stripping simultaneously and all supported VLAN filtering
must either be enabled or disabled together.

Disable inner VLAN stripping by default when DVM is enabled. If a VSI
supports stripping the inner VLAN in DVM, then it will have to configure
that during runtime. For example if a VF is configured in a port VLAN
while DVM is enabled it will be allowed to offload inner VLANs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In order to support configuring the device in Double VLAN Mode (DVM),
the DDP and FW have to support DVM. If both support DVM, the PF that
downloads the package needs to update the default recipes, set the
VLAN mode, and update boost TCAM entries.

To support updating the default recipes in DVM, add support for
updating an existing switch recipe's lkup_idx and mask. This is done
by first calling the get recipe AQ (0x0292) with the desired recipe
ID. Then, if that is successful update one of the lookup indices
(lkup_idx) and its associated mask if the mask is valid otherwise
the already existing mask will be used.

The VLAN mode of the device has to be configured while the global
configuration lock is held while downloading the DDP, specifically after
the DDP has been downloaded. If supported, the device will default to
DVM.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add support for the VF driver to be able to request
VIRTCHNL_VF_OFFLOAD_VLAN_V2, negotiate its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS, add/delete VLAN filters, and
enable/disable VLAN offloads.

VFs supporting VIRTCHNL_OFFLOAD_VLAN_V2 will be able to use the
following virtchnl opcodes:

VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS
VIRTCHNL_OP_ADD_VLAN_V2
VIRTCHNL_OP_DEL_VLAN_V2
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING_V2
VIRTCHNL_OP_ENABLE_VLAN_INSERTION_V2
VIRTCHNL_OP_DISABLE_VLAN_INSERTION_V2

Legacy VF drivers may expect the initial VLAN stripping settings to be
configured by the PF, so the PF initializes VLAN stripping based on the
VIRTCHNL_OP_GET_VF_RESOURCES opcode. However, with VLAN support via
VIRTCHNL_VF_OFFLOAD_VLAN_V2, this function is only expected to be used
for VFs that only support VIRTCHNL_VF_OFFLOAD_VLAN, which will only
be supported when a port VLAN is configured. Update the function
based on the new expectations. Also, change the message when the PF
can't enable/disable VLAN stripping to a dev_dbg() as this isn't fatal.

When a VF isn't in a port VLAN and it only supports
VIRTCHNL_VF_OFFLOAD_VLAN when Double VLAN Mode (DVM) is enabled, then
the PF needs to reject the VIRTCHNL_VF_OFFLOAD_VLAN capability and
configure the VF in software only VLAN mode. To do this add the new
function ice_vf_vsi_cfg_legacy_vlan_mode(), which updates the VF's
inner and outer ice_vsi_vlan_ops functions and sets up software only
VLAN mode.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently the driver only supports 802.1Q VLAN insertion and stripping.
However, once Double VLAN Mode (DVM) is fully supported, then both 802.1Q
and 802.1ad VLAN insertion and stripping will be supported. Unfortunately
the VSI context parameters only allow for one VLAN ethertype at a time
for VLAN offloads so only one or the other VLAN ethertype offload can be
supported at once.

To support this, multiple changes are needed.

Rx path changes:

[1] In DVM, the Rx queue context l2tagsel field needs to be cleared so
the outermost tag shows up in the l2tag2_2nd field of the Rx flex
descriptor. In Single VLAN Mode (SVM), the l2tagsel field should remain
1 to support SVM configurations.

[2] Modify the ice_test_staterr() function to take a __le16 instead of
the ice_32b_rx_flex_desc union pointer so this function can be used for
both rx_desc->wb.status_error0 and rx_desc->wb.status_error1.

[3] Add the new inline function ice_get_vlan_tag_from_rx_desc() that
checks if there is a VLAN tag in l2tag1 or l2tag2_2nd.

[4] In ice_receive_skb(), add a check to see if NETIF_F_HW_VLAN_STAG_RX
is enabled in netdev->features. If it is, then this is the VLAN
ethertype that needs to be added to the stripping VLAN tag. Since
ice_fix_features() prevents CTAG_RX and STAG_RX from being enabled
simultaneously, the VLAN ethertype will only ever be 802.1Q or 802.1ad.

Tx path changes:

[1] In DVM, the VLAN tag needs to be placed in the l2tag2 field of the Tx
context descriptor. The new define ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN was
added to the list of tx_flags to handle this case.

[2] When the stack requests the VLAN tag to be offloaded on Tx, the
driver needs to set either ICE_TX_FLAGS_HW_OUTER_SINGLE_VLAN or
ICE_TX_FLAGS_HW_VLAN, so the tag is inserted in l2tag2 or l2tag1
respectively. To determine which location to use, set a bit in the Tx
ring flags field during ring allocation that can be used to determine
which field to use in the Tx descriptor. In DVM, always use l2tag2,
and in SVM, always use l2tag1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add a new outer_vlan_ops member to the ice_vsi structure as outer VLAN
ops are only available when the device is in Double VLAN Mode (DVM).
Depending on the VSI type, the requirements for what operations to
use/allow differ.

By default all VSI's have unsupported inner and outer VSI VLAN ops. This
implementation was chosen to prevent unexpected crashes due to null
pointer dereferences. Instead, if a VSI calls an unsupported op, it will
just return -EOPNOTSUPP.

Add implementations to support modifying outer VLAN fields for VSI
context. This includes the ability to modify VLAN stripping, insertion,
and the port VLAN based on the outer VLAN handling fields of the VSI
context.

These functions should only ever be used if DVM is enabled because that
means the firmware supports the outer VLAN fields in the VSI context. If
the device is in DVM, then always use the outer_vlan_ops, else use the
vlan_ops since the device is in Single VLAN Mode (SVM).

Also, move adding the untagged VLAN 0 filter from ice_vsi_setup() to
ice_vsi_vlan_setup() as the latter function is specific to the PF and
all other VSI types that need an untagged VLAN 0 filter already do this
in their specific flows. Without this change, Flow Director is failing
to initialize because it does not implement any VSI VLAN ops.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Current operations act on inner VLAN fields. To support double VLAN, outer
VLAN operations and functions will be implemented. Add the "inner" naming
to existing VLAN operations to distinguish them from the upcoming outer
values and functions. Some spacing adjustments are made to align
values.

Note that the inner is not talking about a tunneled VLAN, but the second
VLAN in the packet. For SVM the driver uses inner or single VLAN
filtering and offloads and in Double VLAN Mode the driver uses the
inner filtering and offloads for SR-IOV VFs in port VLANs in order to
support offloading the guest VLAN while a port VLAN is configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The current vf->port_vlan_info variable is a packed u16 that contains
the port VLAN ID and QoS/prio value. This is fine, but changes are
incoming that allow for an 802.1ad port VLAN. Add flexibility by
changing the vf->port_vlan_info member to be an ice_vlan structure.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There are multiple places where VLAN 0 is being added. Create a function
to be called in order to minimize changes as the implementation is expanded
to support double VLAN and avoid duplicated code.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add functions to configure Tx VLAN antispoof based on iproute
configuration and/or VLAN mode and VF driver support. This is needed
later so the driver can control when it can be configured. Also, add
functions that can be used to enable and disable MAC and VLAN
spoofcheck. Move spoofchk configuration during VSI setup into the
SR-IOV initialization path and into the post VSI rebuild flow for VF
VSIs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

On ppc64le architecture __s64 is long int and requires %ld. Cast to
ssize_t and use %zd to avoid architecture-specific specifiers.

Fixes: 4172843e ("libbpf: Fix signedness bug in btf_dump_array_data()")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220209063909.1268319-1-andrii@kernel.org

Provide generic selftest support. Tested with LAN9500 and LAN9512.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

do_div() does a 64-by-32 division.
When the divisor is u64, do_div() truncates it to 32 bits, this means it
can test non-zero and be truncated to zero for division.

fix do_div.cocci warning:
do_div() does a 64-by-32 division, please consider using div64_u64 instead.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we can use the enetc_cbd_alloc_data_mem() to replace complicated DMA
data alloc method and CBDR memory basic seting.
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate the CBDR data memory alloc standalone. It is convenient for
other part loading, for example the ENETC QOS part.
Reported-and-suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To replace the dma_map_single() stream DMA mapping with DMA coherent
method dma_alloc_coherent() which is more simple.

dma_map_single() found by Tim Gardner not proper. Suggested by Claudiu
Manoil and Jakub Kicinski to use dma_alloc_coherent(). Discussion at:

https://lore.kernel.org/netdev/AM9PR04MB8397F300DECD3C44D2EBD07796BD9@AM9PR04MB8397.eurprd04.prod.outlook.com/t/

Fixes: 888ae5a3 ("net: enetc: add tc flower psfp offload driver")
cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add support for software TSO

This series adds support for driver level TSO in the dpaa2-eth driver.

The first 5 patches lay the ground work for the actual feature:
rearrange some variable declaration, cleaning up the interraction with
the S/G Table buffer cache etc.

The 6th patch adds the actual driver level software TSO support by using
the usual tso_build_hdr()/tso_build_data() APIs and creates the S/G FDs.

With this patch set we can see the following improvement in a TCP flow
running on a single A72@2.2GHz of the LX2160A SoC:

before: 6.38Gbit/s
after:  8.48Gbit/s
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Once we added support in the dpaa2-eth for driver level software TSO we
observed the following situation: if the EQCR CI (consumer index) is
read from the cache-enabled area we sometimes end up with a computed
value of available enqueue entries bigger than the size of the ring.

This eventually will lead to the multiple enqueue of the same FD which
will determine the same FD to end up on the Tx confirmation path and the
same skb being freed twice.

Just read the consumer index from the cache inhibited area so that we
avoid this situation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for driver level TSO in the enetc driver using
the TSO API.

There is not much to say about this specific implementation. We are
using the usual tso_build_hdr(), tso_build_data() to create each data
segment, we create an array of S/G FDs where the first S/G entry is
referencing the header data and the remaining ones the data portion.

For the S/G Table buffer we use the same cache of buffers used on the
other non-GSO cases - dpaa2_eth_sgt_get() and dpaa2_eth_sgt_recycle().

We cannot keep a DMA coherent buffer for all the TSO headers because the
DPAA2 architecture does not work in a ring based fashion so we just
allocate a buffer each time.

Even with these limitations we get the following improvement in TCP
termination on the LX2160A SoC, on a single A72 core running at 2.2GHz.

before: 6.38Gbit/s
after:  8.48Gbit/s
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now, the __dpaa2_eth_tx function used a single FD on the stack
to construct the structure to be enqueued. Since we are now preparing
the ground work to add support for TSO done in software at the driver
level, the same function needs to work with an array of FDs and enqueue
as many as the build_*_fd functions create.

Make the necessary adjustments in order to do this. These include:
keeping an array of FDs in a percpu structure, cleaning up the necessary
FDs before populating it and then, retrying the enqueue process up till
all the generated FDs were enqueued or until we reach the maximum number
retries.

This patch does not change the fact that only a single FD will result
from a __dpaa2_eth_tx call but rather just creates the necessary changes
for the next patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>