This patch adds Adreno 618 entry and its associated properties
to the gpulist entries.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

At the moment, the MSM DSI driver calls drm_panel_enable() rather early
from the DSI bridge pre_enable() function. At this point, the encoder
(e.g. MDP5) is not enabled, so we have not started transmitting
video data.

However, the drm_panel_funcs documentation states that enable()
should be called on the panel *after* video data is being transmitted:

  The .prepare() function is typically called before the display controller
  starts to transmit video data. [...] After the display controller has
  started transmitting video data, it's safe to call the .enable() function.
  This will typically enable the backlight to make the image on screen visible.

Calling drm_panel_enable() too early causes problems for some panels:
The TFT LCD panel used in the Samsung Galaxy Tab A 9.7 (2015) (APQ8016)
uses the MIPI_DCS_SET_DISPLAY_BRIGHTNESS command to control
backlight/brightness of the screen. The enable sequence is therefore:

  drm_panel_enable()
    drm_panel_funcs.enable():
      backlight_enable()
        backlight_ops.update_status():
          mipi_dsi_dcs_set_display_brightness(dsi, bl->props.brightness);

The panel seems to silently ignore the MIPI_DCS_SET_DISPLAY_BRIGHTNESS
command if it is sent too early. This prevents setting the initial brightness,
causing the display to be enabled with minimum brightness instead.
Adding various delays in the panel initialization code does not result
in any difference.

On the other hand, moving drm_panel_enable() to dsi_mgr_bridge_enable()
fixes the problem, indicating that the panel requires the video stream
to be active before the brightness command is accepted.

Therefore: Move drm_panel_enable() to dsi_mgr_bridge_enable() to
delay calling it until video data is being transmitted.

Move drm_panel_disable() to dsi_mgr_bridge_disable() for similar reasons.
(This is not strictly required for the panel affected above...)
Tested-by: Jasper Korten <jja2000@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Fix max core clk rate during dt parsing in display driver.
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add scaler support for display driver.

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11260267/Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

mixer selection in the display topology is based on multiple
factors
1) mixers available in the hw
2) interfaces to be enabled
3) merge capability

change will pickup mixer as per the topology need.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add changes to setup display datapath on SC7180 target.

Changes in v1:
 - Add changes to support ctl_active on SC7180 target.
 - While selecting the number of mixers in the topology
   consider the interface width.

Changes in v2:
 - Spawn topology mixer selection into separate patch (Rob Clark).
 - Add co-developed-by tags in the commit msg (Stephen Boyd).

Changes in v3:
 - Fix kernel checkpatch errors in v2.

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11253747/Co-developed-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add display hw catalog changes for SC7180 target.

Changes in v1:
 - Configure register offsets and capabilities for the
   display hw blocks.

Changes in v2:
 - mdss_irq data type has changed in the dependent
   patch, accommodate the necessary changes.
 - Add co-developed-by tags in the commit msg (Stephen Boyd).

Changes in v3:
 - fix kernel checkpatch errors in v2

Changes in v4:
 - move documentation into seperate patch (Rob Herring).

This patch has dependency on the below series

https://patchwork.kernel.org/patch/11253647/Co-developed-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Co-developed-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
[rebase on hw catalog const'ification, and add more const's]
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add a compatible string to support sc7180 dpu version.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Current code assumes that all the irqs registers offsets can be
accessed in all the hw revisions; this is not the case for some
targets that should not access some of the irq registers.
This change adds the support to selectively remove the irqs that
are not supported in some of the hw revisions.

Changes in v1:
 - Add support to selectively remove the hw irqs that are not
   not supported.

Changes in v2:
 - Remove unrelated changes.

Changes in v3:
 - Remove change-id (Stephen Boyd).
 - Add colon in variable description to match kernel-doc (Stephen Boyd).
 - Change macro-y way of variable description (Jordon Crouse).
 - Remove unnecessary if checks (Jordon Crouse).
 - Remove extra blank line (Jordon Crouse).

Changes in v4:
 - Remove checkpatch errors.
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Hardware only natively supports BGR8888 UBWC.
UBWC support for RGB8888 can be had by pretending
that the buffer is BGR.
Signed-off-by: Fritz Koenig <frkoenig@google.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@chromium.org>

These structures look like a bunch of data tables that aren't going to
change after boot. Let's move them to the const RO section of memory so
that they can't be modified at runtime on modern machines.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Set the two interconnect paths for the GPU to maximum speed for now to
work towards getting the GPU working upstream. We can revisit a later
time to optimize this for battery life.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Set the two interconnect paths for the GPU to maximum speed for now to
work towards getting the GPU working upstream. We can revisit a later
time to optimize this for battery life.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Some A3xx and all A4xx Adreno GPUs do not have GMEM inside the GPU core
and must use the On Chip MEMory (OCMEM) in order to be functional.
There's a separate interconnect path that needs to be setup to OCMEM.
Add support for this second path to the GPU core.

In the downstream MSM 3.4 sources, the two interconnect paths for the
GPU are between:

  - MSM_BUS_MASTER_GRAPHICS_3D and MSM_BUS_SLAVE_EBI_CH0
  - MSM_BUS_MASTER_V_OCMEM_GFX3D and MSM_BUS_SLAVE_OCMEM
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Some A3xx and all A4xx Adreno GPUs do not have GMEM inside the GPU core
and must use the On Chip MEMory (OCMEM) in order to be functional.
There's a separate interconnect path that needs to be setup to OCMEM.
Let's document this second interconnect path that's available. Since
there's now two available interconnects, let's add the
interconnect-names property.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We can have two cases, when it comes to "zap" fw.  Either the fw
requires zap fw to take the GPU out of secure mode at boot, or it does
not and we can write RBBM_SECVID_TRUST_CNTL directly.  Previously we
decided based on whether zap fw load succeeded, but this is not a great
plan because:

1) we could have zap fw in the filesystem on a device where it is not
   required
2) we could have the inverse case

Instead, shift to deciding based on whether we have a 'zap-shader' node
in dt.  In practice, there is only one device (currently) with upstream
dt that does not use zap (cheza), and it already has a /delete-node/ for
the zap-shader node.

Fixes: abccb9fe ("drm/msm/a6xx: Add zap shader load")
Signed-off-by: Rob Clark <robdclark@chromium.org>

Previously, if the freq were overriden (ie. via sysfs), it would get
reset to max on resume.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>

This isn't an error.  Also the clk APIs handle the NULL case, so we can
just delete the check.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>

Pull RISC-V fixes from Paul Walmsley:
 "One important fix for RISC-V:

   - Redirect any incoming syscall with an ID less than -1 to
     sys_ni_syscall, rather than allowing them to fall through into the
     syscall handler.

  and two minor build fixes:

   - Export __asm_copy_{from,to}_user() from where they are defined.
     This fixes a build error triggered by some randconfigs.

   - Export flush_icache_all(). I'd resisted this before, since
     historically we didn't want modules to be able to flush the I$
     directly; but apparently everyone else is doing it now"

* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: export flush_icache_all to modules
  riscv: reject invalid syscalls below -1
  riscv: fix compile failure with EXPORT_SYMBOL() & !MMU

Pull /proc/locks formatting fix from Jeff Layton:
 "This is a trivial fix for a _very_ long standing bug in /proc/locks
  formatting. Ordinarily, I'd wait for the merge window for something
  like this, but it is making it difficult to validate some overlayfs
  fixes.

  I've also gone ahead and marked this for stable"

* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  locks: print unsigned ino in /proc/locks

Pull cifs fixes from Steve French:
 "One performance fix for large directory searches, and one minor style
  cleanup noticed by Clang"

* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Optimize readdir on reparse points
  cifs: Adjust indentation in smb2_open_file

An ino is unsigned, so display it as such in /proc/locks.

Cc: stable@vger.kernel.org
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>

This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.

Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.

I forgot to redirect any syscall below -1 to sys_ni_syscall.

With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
  .../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
  .../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here

Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).

Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.

Fixes: 6bd33e1e ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Pull SCSI fixes from James Bottomley:
 "Four fixes and one spelling update, all in drivers: two in lpfc and
  the rest in mp3sas, cxgbi and target"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target/iblock: Fix protection error with blocks greater than 512B
  scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
  scsi: lpfc: fix spelling mistakes of asynchronous
  scsi: lpfc: fix build failure with DEBUGFS disabled
  scsi: mpt3sas: Fix double free in attach error handling

Pull drm fixes from Dave Airlie:
 "Post-xmas food coma recovery fixes. Only three fixes for i915 since I
  expect most people are holidaying.

  i915:
   - power management rc6 fix
   - framebuffer tracking fix
   - display power management ratelimit fix"

* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
  drm/i915: Hold reference to intel_frontbuffer as we track activity
  drm/i915/gt: Ratelimit display power w/a
  drm/i915/pmu: Ensure monotonic rc6

Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:

 - rseq build failures fixes related to glibc 2.30 compatibility from
   Mathieu Desnoyers

 - Kunit fixes and cleanups from SeongJae Park

 - Fixes to filesystems/epoll, firmware, and livepatch build failures
   and skip handling.

* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  rseq/selftests: Clarify rseq_prepare_unload() helper requirements
  rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
  rseq/selftests: Turn off timeout setting
  kunit/kunit_tool_test: Test '--build_dir' option run
  kunit: Rename 'kunitconfig' to '.kunitconfig'
  kunit: Place 'test.log' under the 'build_dir'
  kunit: Create default config in '--build_dir'
  kunit: Remove duplicated defconfig creation
  docs/kunit/start: Use in-tree 'kunit_defconfig'
  selftests: livepatch: Fix it to do root uid check and skip
  selftests: firmware: Fix it to do root uid check and skip
  selftests: filesystems/epoll: fix build error

Pull power management fixes from Rafael Wysocki:
 "Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
  remove redundant Kconfig dependencies from multiple devfreq drivers
  (Leonard Crestez)"

* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / devfreq: tegra: Add COMMON_CLK dependency
  PM / devfreq: Drop explicit selection of PM_OPP

Pull io_uring fixes from Jens Axboe:

 - Removal of now unused busy wqe list (Hillf)

 - Add cond_resched() to io-wq work processing (Hillf)

 - And then the series that I hinted at from last week, which removes
   the sqe from the io_kiocb and keeps all sqe handling on the prep
   side. This guarantees that an opcode can't do the wrong thing and
   read the sqe more than once. This is unchanged from last week, no
   issues have been observed with this in testing. Hence I really think
   we should fold this into 5.5.

* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
  io-wq: add cond_resched() to worker thread
  io-wq: remove unused busy list from io_sqe
  io_uring: pass in 'sqe' to the prep handlers
  io_uring: standardize the prep methods
  io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
  io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
  io_uring: move all prep state for IORING_OP_CONNECT to prep handler
  io_uring: add and use struct io_rw for read/writes
  io_uring: use u64_to_user_ptr() consistently

Pull libata fixes from Jens Axboe:
 "Two things in here:

   - First half of a series that fixes ahci_brcm, also marked for
     stable. The other part of the series is going into 5.6 (Florian)

   - sata_nv regression fix that is also marked for stable (Sascha)"

* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
  ata: ahci_brcm: Add missing clock management during recovery
  ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
  ata: ahci_brcm: Fix AHCI resources management
  ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
  libata: Fix retrieving of active qcs

Pull block fixes from Jens Axboe:
 "Only thing here are the changes from Arnd from last week, which now
  have the appropriate header include to ensure they actually compile if
  COMPAT is enabled"

* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
  compat_ioctl: block: handle Persistent Reservations
  compat_ioctl: block: handle add zone open, close and finish ioctl
  compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
  compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
  pktcdvd: fix regression on 64-bit architectures

Pull GPIO fixes from Linus Walleij:
 "A set of fixes for the v5.5 series:

   - Fix the build for the Xtensa driver.

   - Make sure to set up the parent device for mpc8xxx.

   - Clarify the look-up error message.

   - Fix the usage of the line direction in the mockup device.

   - Fix a type warning on the Aspeed driver.

   - Remove the pointless __exit annotation on the xgs-iproc which is
     causing a compilation problem.

   - Fix up emultation of open drain outputs .get_direction()

   - Fix the IRQ callbacks on the PCA953xx to use bitops and work
     properly.

   - Fix the Kconfig on the Tegra driver"

* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: tegra186: Allow building on Tegra194-only configurations
  gpio: pca953x: Switch to bitops in IRQ callbacks
  gpiolib: fix up emulated open drain outputs
  MAINTAINERS: Append missed file to the database
  gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
  gpio: aspeed: avoid return type warning
  gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
  gpio: Fix error message on out-of-range GPIO in lookup table
  gpio: mpc8xxx: Add platform device to gpiochip->parent
  gpio: xtensa: fix driver build

Merge tag 'drm-intel-fixes-2019-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

i915 power and frontbuffer tracking fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87r20vdlrs.fsf@intel.com

The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.

Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.

Fixes: eb73390a ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.

This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.

We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.

Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.

This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.

As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.

The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.

Fixes: eba68f82 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This reverts commit 6bb86fef
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.

Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.

Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ata_qc_complete_multiple() is called with a mask of the still active
tags.

mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)

Since 28361c40 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.

This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.

This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.

Fixes: 28361c40 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>